CHAPTER 1 GENERAL ADJUSTMENTS SAFETY INSTRUCTIONS WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAU- TION” AND “PRODUCT SAFETY NOTICE” INSTRUCTIONS BELOW. X-RAY RADIATION PRECAUTION 1. Excessive high voltage can produce potentially hazardous 2. The only source of X-RAY RADIATION in this TV receiver X-RAY RADIATION.
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAU- TION” AND “PRODUCT SAFETY NOTICE” ON PAGE 3 OF SERVICE MANUAL. SET-UP ADJUSTMENT ■ The following adjustments should be made when a complete realignment is required or a new picture tube is installed. Perform the adjustments in order as follows : 1.
Page 5
(5)Adjust the sub-4-pole magnets only in case there is any deviation of Xv bow-shaped convergence. (To be usually set at the initial position) Align both sides with the sub-4-pole magnets and minimize the deviation of blue and red with the main 4-pole magnets. Xv bow-shaped deviation of convergence red/blue blue...
SERVICE MODE 1. ENTERING TO SERVICE MODE 1) Press o button once on 2) Press o button again to 3) While pressing the o button, Remote Control. keep pressing. press MENU button on TV set. Item Data or Sound Mute (Service mode display) 2.
Page 7
4. SELECTING THE ADJUSTING ITEMS 1)Every pressing of CHANNEL s button in the service mode changes the adjustment items in the order of table-2. (t button for reverse order) Refer to table-2 for preset data of adjustment mode. (See SETTING & ADJUSTING DATA on page 27) 5.
Page 8
The diagnosis will begin to check if interface among IC’s are executed properly. 2) During diagnosis, the following displays are shown. JH9_000 34JH9UH Firmware: Version information of microprocessor In case of file name : JH9 and Version : 1.00 indicates[JH9_100].
DESIGN MODE 1. ENTERING TO DESIGN MODE 3) The following displays 1) Select the Service mode. 2) While pressing CALL button on Remote and press MENU button on TV. are shown on the screen Press Press JH9_039 (Design mode) Version information of microprocessor Main tuner information Sub tuner information...
ELECTRICAL ADJUSTMENTS ITEM ADJUSTMENT PROCEDURE FOCUS VR ADJ 1. Enter the service mode, then select any register item. 2. Press the TV/VIDEO button on the Remote until the black cross-bar pattern ap- pears on the screen. 3. Adjust the FOCUS control (on T461) for well defined scanning lines on the picture screen.
Page 11
ITEM ADJUSTMENT PROCEDURE WIDTH 1. Call up the adjustment mode display, then select the item WID. (WID) 2. Press the ; – /+ button to get the picture so the left and rightedges of raster begins to lack. 3. Press the ; – /+ button to advance the data by 7 steps. Note : Check the horizontal picture position is correct.
Page 12
V/C system adjustment ADJUSTING ITEMS ADJUSTMENT PROCEDURE REMARKS AND POINTS Cutoff adjustment and 1) Setting to horizontal alignment, turn the screen VR to No outside lighting shall be allowed. white balance adjust- stop where the brightness lines are slightly luminous. Measurement shall be ment (Adjustment shall be made so that they look almost...
Page 13
Circuit Adjustment (Procedure Manual for Deflection Adjustment) ADJUSTING ITEMS ADJUSTMENT PROCEDURE AND POINTS Focus Adjustment (1) Conditions : PAL RETMA ch Static (main): T461 Screen Size : Wide Dynamic : T461 Presentation Mode : Dynamic Only for 34-inch model Adjustment Procedure: 1) Turn the static VR knob to the “MIN.”...
Page 14
Horizontal adjustment * Deflection adjustment shall be made from PAL/100 Hz/WIDE mode. ADJUSTING ITEMS ADJUSTMENT PROCEDURE AND POINTS Hori- For PAL/100 Hz/WIDE <Adjustment condition> zontal Horizontal amplitude Horizontal adjusment shall be made using E-12CH Philips pattern and DY- (WID) NAMIC image mode. Side pin distortion (PARA) <Adjustment procedure>...
Page 15
Vertical adjustment ADJUSTING ITEMS ADJUSTMENT PROCEDURE AND POINTS Verti- For PAL WIDE 1) With E-12ch, WIDE mode, DYNAMIC and 100 Hz, adjust the vertical screen posi- Vertical amplitude tion (VPOS) and amplitude (HIT) as shown in the following figure: (HIT) Flags shall just be blinded.
Page 16
Geomagnetic compensation (chassis adjustment) ADJUSTING ITEMS ADJUSTMENT PROCEDURE AND POINTS Output voltage control Conditions: User control for geomagnetic compensation: 0 (GMF) Geomagnetic compensation coil: Unconnected Perform voltage measurement at both ends of RJ06 and adjust the volt- age to the following adjustable value with GMF of data adjustment mode: 0 ±...
CIRCUIT CHECK HIGH VOLTAGE CHECK CAUTION: There is no HIGH VOLTAGE ADJUSTMENT on this chassis. Checking should be done following the steps below. 1. Connect an accurate high voltage meter to the second anode of the picture tube. 2. Turn on the receiver. Set the BRIGHTNESS and CONTRAST controls to minimum (zero beam current). 3.
LOCATION OF CONTROLS Front Press here to open r On-timer indicator the door. 7 POWER indicator f - 7 POWER switch Remote sensor a Input source selection Behind the door L/MONO VIDEO AUDIO S-VIDEO MENU MENU Channel position t s Headphone jack a (3) Video 3 input Menu...
PROGRAMMING CHANNEL MEMORY • First, use the Auto tuning feature to preset all the active channels in your area automatically. Then, arrange the preset channels with the Manual tuning feature so that you can tune in only desired channels. • Use the Channel search operation if desired channels cannot be preset with the Auto tuning or if you would like to preset channels to specific position numbers one by one.
Page 22
E. Channel search operation Press the button to search up the band or the button to search down the band. Press the button repeatedly until your desired channel is displayed. When a station/satellite is found, it will be displayed. F. Auto Fine Tuning Press the button to turn the Auto Fine Tuning option On “...
• The part number must be used when ordering parts, in order to assist in processing, be sure to include the Model number and Description. ∗ • The PC board assembly with mark is no longer available after the end of the production. Model : 34JH9UH Capacitors ..... CD Ceramic Disk : Plastic Film : Electrolytic Resistors ....
Page 24
Location Location Parts No. Description Parts No. Description C565 24092785 CERAMIC CHIP, 10V B 0.47UF K C814 24092563 CERAMIC DISC, AC250V B 220PF K C815 24092567 CERAMIC DISC, AC250V E 1000PF M C568 24014104 CERAMIC CHIP, 16V F 0.1UF Z C572 24014104 CERAMIC CHIP, 16V F 0.1UF Z...
Page 25
Location Location Parts No. Description Parts No. Description C4427 24092789 CERAMIC CHIP, 6.3V B 1UF K C8131 24092795 CERAMIC CHIP CK73B 6.3V 2.2UP K C4460 24092796 CERAMIC CHIP CK732B 50V 220000PF K C8132 24092795 CERAMIC CHIP CK73B 6.3V 2.2UP K C4461 24092796 CERAMIC CHIP CK732B 50V 220000PF K...
Page 26
Location Location Parts No. Description Parts No. Description CA54 24015104 CERAMIC CHIP CK73B 6.3V 100,000PF K CV11 24092731 CERAMIC CHIP, 16V B 1UF K CA55 24092621 CERAMIC CHIP, 10V B 1UF K CV12 24092731 CERAMIC CHIP, 16V B 1UF K CA56 24092621 CERAMIC CHIP, 10V B 1UF K...
Page 27
Location Location Parts No. Description Parts No. Description CX339 24015105 CHIP CERA CAP B 6.3V 105K CX605 24015105 CHIP CERA CAP B 6.3V 105K CX340 24015105 CHIP CERA CAP B 6.3V 105K CX606 24015105 CHIP CERA CAP B 6.3V 105K CX341 24092795 CERAMIC CHIP CK73B 6.3V 2.2UP K...
Page 28
Location Location Parts No. Description Parts No. Description CX945 24092795 CERAMIC CHIP CK73B 6.3V 2.2UP K CZ34 24013270 CERAMIC CHIP, 50V CH 27PF J CX946 24092795 CERAMIC CHIP CK73B 6.3V 2.2UP K CZ36 24015104 CERAMIC CHIP CK73B 6.3V 100,000PF K CX947 24092795 CERAMIC CHIP CK73B 6.3V 2.2UP K...
Page 29
Location Location Parts No. Description Parts No. Description R362 24012223 CHIP, METAL FILM, 1/16W 22K OHM J R572 24012562 METAL FILM CHIP 1005 1/16W 5R6K J R363 24012472 CHIP, METAL FILM, 1/16W 4.7K OHM J R601 24011333 CHIP, METAL FILM, 1/20W 33K OHM J R370 24872103 CHIP, 1/16W 10K OHM J...
SCHEMATIC DIAGRAM MODEL : 34JH9UH WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION", "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" ON THE MANUAL FOR THIS MODEL. CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
SPECIFICATIONS MODEL 34JH9UH Rated voltage g 220 – 240 V, 50 Hz Power consumption 200 W (at g 220 V, 50 Hz) Dimensions 829mm × 556mm × 689mm (Width × Depth × Height) Mass 75.5 kg Type 34, picture tube Picture tube 86 cm (dia.) overall picture tube...