Subscribe to Our Youtube Channel
Related Manuals for COMPANION Aquacube COMP827
Summary of Contents for COMPANION Aquacube COMP827
-
Page 1: Owners Manual
Owners Manual aQuaCuBe rV digital water heater Part No. ComP827 warning OutdOOr use OnlY ® AUSTRALIA ONLY SAI Global GAS SAFETY Cert. SAI - 400097 CERTIFICATION AS 2658 - 2008 OWNERS MANUAL Australia’s original Outdoor brand... -
Page 2: General Warnings
iMpOrtant: read these instructions for use carefully. Familiarise yourself with the appliance before connecting it to a gas container. Keep these instructions for future reference. GENERAL WARNINGS • This appliance shall only be used with a Propane Gas Cylinder certified to Standard AS2469 that is fitted with a POL valve and the 1500mm Propane Hose &... - Page 3 Owners Manual IMPORTANT • uSe OuTdOORS OnLy – The appliance must be used outdoors only and is to be operated no closer than 1000mm from the sides and 1000mm from above all combustible surfaces, fabrics and flammable materials. • CAuTIOn: Accessible parts may be very hot. Keep young children away. •...
-
Page 4: Safety Instructions
SAFETy INSTRUCTIONS This appliance shall only be used in an above ground open air situation with natural ventilation, without stagnant areas, where gas leakage and products of combustion are rapidly dispersed by wind and natural convection. any enclosure in which the appliance is used shall comply with one of the following: (a) An enclosure with walls on all sides, but with no overhead cover. -
Page 5: Carbon Monoxide Hazard
Owners Manual CARBON MONOXIDE HAZARD using this applianCe in an enClOsed spaCe MaY Cause death. dO nOt use in CaraVans, tents, Marine CraFt, Cars, MOBile hOMes Or siMilar lOCatiOns. ImPORTAnT – This appliance is designed to be used with a source water temperature of 20ºC or below, if the temperature of the outlet water exceeds 45º... - Page 6 UNDERSTANDING yOUR APPLIANCE carry HanDLe raIn coWL Front paneL moDe controL bUrner VIeW WInDoW Water controL controL 12V poWer LcD paneL SWItcH GaS InLet battery Water oUtLet (2 x "D" ceLL) not IncL. Water InLet ”d” Cell battery to power electronic ignition...
- Page 7 Owners Manual SETTING UP The COmP827 is designed to be positioned in a vertical position and is to be partly sheltered from the rain and the potential to be sprayed by the shower head whilst in operation. This appliance is not designed to be used as a permanent shower or supply of hot water.
- Page 8 step 6. Check that the power switch is in the “Off” position and Connect the cigarette lighter fitting to a suitable 12vdC power source step 7. Insert the 2 “d” Cell batteries (not included) in to the shower and lock the door step 8.
- Page 9 Owners Manual PACKING THE APPLIANCE step 1. disconnect the power and gas supply to the appliance. step 2. disconnect the pump and shower head checking the flow switch is in the “On” position, hold the hoses vertically until all the water has been drained.
-
Page 10: Technical Details
TECHNICAL DETAILS speCiFiCatiOns Part no: COmP827 Water flow: 3 litres per minute (Average) Inlet voltage: 12v dC - 5A Size: 290 x 153 x 550mm Weight: 6.54 Kgs Injector size: 0.60mm x 6 Consumption: 20.53 mj/hr CARE INSTRUCTIONS using warm soapy water with a mild detergent wipe down all surfaces and areas of the appliance, taking care not to allow water to enter the burner outlets. -
Page 11: Troubleshooting Guide
Owners Manual TROUBLE SHOOTING GUIDE dO nOt atteMpt tO repair Or MOdiFY the applianCe The guide should be followed in case of failure of the appliance to operate correctly. If symptoms persist contact Customer Service on 1300 555 197. ERROR CODES prOBleM Cause The appliance is fitted with operational &... - Page 12 Companion Brands bundoora victoria 3083 www.companionbrands.com.au...
Need help?
Do you have a question about the Aquacube COMP827 and is the answer not in the manual?
Questions and answers
burner will not ignite
The COMPANION Aquacube COMP827 burner may not ignite if the following steps are not followed correctly:
1. MODE control is not set to SUMMER.
2. GAS control is not set to LOW.
3. WATER FLOW is not set to HIGH.
4. SHOWER HEAD flow control switch is not turned ON or SPRAY PATTERN is not set to the OUTSIDE RING.
5. POWER SWITCH is not turned ON.
Also, ensure there is no obstruction in the primary air intakes and that gas connections are tight with no leaks.
This answer is automatically generated