Advertisement
Quick Links
Advertisement
Summary of Contents for Sparklan OA200
-
Page 1: Quick Installation Guide
OA200 Outdoor 802.11ag AP Quick Installation Guide Version 1.0... -
Page 2: Table Of Contents
Content 1. Introduction ............3 2. Operating Mode............ 4 3. Hardware Installation........... 6 4. Quick Setup Guide..........11 5. Waterproof RJ-45 Connector Assembly ... 15... -
Page 3: Introduction
OA200 designs to support large areas. This unit is built-in high power RF module. Installation OA200 is very easy to install and set up. Power over Ethernet support offers the power for this unit and decreases most effort on installation. -
Page 4: Operating Mode
In AP mode, it can connect multiple wireless clients to a wired network. 2.2 AP Repeater mode AP Repeater mode allows OA200 to communicate with other 802.11ag APs while functioning in AP mode, and to extend your Wireless Network coverage. -
Page 5: Wds Mode
For building-to-building wireless connection, each building should implement one OA200 as WDS. In this case, the OA200 can act as a wireless bridge between the two wired and wireless networks. Please fill in remote AP’s MAC address in “WDS links”... -
Page 6: Hardware Installation
3. Hardware Installation 3.1 LED Description There are 3 LEDs on the right side of OA200. 1. LInk LED Off: No LAN connection available On: LAN connection OK 2. 11g LED Off: no activity Blinking: sending and receiving data 3. 11a LED... - Page 7 Assemble the back of the OA200 housing to the bracket subsequently. 3. If you are mounting the OA200 to a pole, first install the bracket and the clip of the mounting kit to a strong pole. Assemble the rear of the OA200 housing to the bracket subsequently.
- Page 8 3.3 Power over Ethernet Installation 1. Connect the Ethernet cable from the OA200 to PoE hub (LAN out). 2. Connect a second Ethernet cable from the LAN-IN port of the PoE adapter to a free port of a switch or hub within the local network. Please refer to the...
- Page 9 3.4 Hardware Reset to default settings You can reset the wireless bridge unit’s settings to factory defaults by pushing reset button using reset bar. The reset button is located and hidden inside of the rear panel as above figure. Please refer to the following steps to perform the Hardware Reset.
- Page 10 3.5 Antenna installation on OA200 OA200 is one 11ag AP series with external antenna.The cable with male to male antenna inside box, so the external antenna is necessary for this unit. Please N-type connector will be use to connect withOA-200 physical utility. The cable find the RP-SMA Antenna connector on the rear side of this box.
-
Page 11: Quick Setup Guide
4. Quick Setup Guide AP Default Settings The default settings are shown as the following: User Password admin IP Address 192.168.1.250 Subnet Mask 255.255.255.0 RF ESSID A band: wlan-a G band: wlan-g Channel A band: Auto G band: 6 Mode G band: Mixed Encryption Disabled... - Page 12 Step1 START UP & LOGIN In order to configure the OA200, you must use your web browser and manually input http://192.168.1.250 into the Address Box and press Enter. The Main Page will appear. To start configure the OA200, you must input password “admin” on the password section.
- Page 13 Step2 Local Area Network: This is OA200 IP Address and Subnet Mask as seen on the internal LAN. The default value is 192.168.1.250 for IP Address and 255.255.255.0 for Subnet Mask. Please Click “Apply” button to save your settings once you have any change.
- Page 14 Step3 Please select the antenna for each band. After completed the setting and hardware installation, please adjust the direction of OA200 to remote site OA200 for a high quality transmission.
-
Page 15: Waterproof Rj-45 Connector Assembly
5. Waterproof RJ-45 Connector Assembly Recommendation: Please prepare one CAT-5 or better quality Ethernet cable then get through the parts of waterproof connector before this assembly. - Page 16 The equipment has been tested and found to comply with FCC and CE Rules.Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference received including interference that may cause undesired operation. REMARK: 5150MHz~5250MHz, 5250MHz ~ 5350MHz frequency will be disabled by firmware.
- Page 17 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The OA200 ( FCC ID: RYK-OA200 ) is limited in CH1~CH11 for 2.4 GHz by specified firmware controlled in U.S.A.
Need help?
Do you have a question about the OA200 and is the answer not in the manual?
Questions and answers