Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for IDTECK SRK101V
- Page 1 User Manual RFID Reader...
-
Page 2: Table Of Contents
Table of contents ............Table of contents . - Page 3 ............13 1 WIEGAND output .
-
Page 4: Safety Information
Safety Information CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit. - Page 5 5. When installing the controller, fasten it securely and firmly. The fall of controller may cause personal injury. 6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled with water on top of the controller. Doing so may cause personal injury due to fire, electric shock, or falling objects.
-
Page 6: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. -
Page 7: Product Introduction
Product introduction Features This model is an elegant-looking proximity reader that is featured by the capacitive touch-sensing keypad. The back-lighted keypad is useful especially for night operation, and its epoxy adhesion and aluminium case relieve you of worries about the rain or any other challenging weather conditions. -
Page 8: What's Included
What's included Check if the following items are included in the product package. At a glance Front / Rear Figure 2-1 rf10structure 1. LED Displays the status of the system operation. Product introduction... -
Page 9: Cable Color Scheme
2. Keypad Used to enter the ID/password. 3. Tamper Switch A tamper switch to detect falling from the wall. 4. Connection Cable Used to connect to the power or I/O cable. 5. Buzzer Piezo buzzer. 6. Fixing Hole Fixing hole for wall-mounting. Cable color scheme Item Cable color... -
Page 10: Installation And External Connection
Installation and external connection Installation 1. See [Figure 1] to drill 6-32” holes and 1/2” holes (totally 4) into the wall. 2. Tighten the four screws to secure the product to the wall. 3. With the provided 3mm hex wrench, fix the outer case to the product. -
Page 11: Precautions On Installation
Precautions on installation If installing on a metal wall If you install the reader on a metal wall, the read range may be reduced. To avoid this problem, it is recommended to insert the spacer between the metal wall and the reader as shown below. -
Page 12: External Connection
External connection Wiring Diagram Item Cable Wiring Power Supply Unit Connect the DC+12V to the red line. Connect GND to the black line. Wiegand Connection Connect the green line of the product to the Wiegand D0 input port of the Installation and external connection... - Page 13 Item Cable Wiring controller. Connect the white line of the product to the Wiegand D1 input port of the controller. LED Control Enables you to turn on or off the LED indicators. To control green indicator, connect the yellow line to the controller’s output (relay).
-
Page 14: Initialization
Initialization Basic operations Initial state (when the power is supplied) When you apply power to the product, it will sound beep three times before entering Standby with the red indicator turned on. Using the card Present the card to the product until you hear a beep and the green indicator turns on. The reader keeps the green indicator turned on while transferring the card data to the controller. -
Page 15: Buzzer Control
You can turn on/off the indicators according to the I/O settings of the controller, which can be applied to various situations. For more information about the I/O settings of the controller, refer to the user manual of the controller. To control the orange indicator, connect the gray line to NC of the controller. Buzzer Control Connect the buzzer control input line (blue) to the NO port of the controller relay output, and GND to the COM port. -
Page 16: Output Format
Output format WIEGAND output Timing Diagram Data Format (34-bit) Bit 1 : Even Parity (bit 2 ~ bit 17) ● Bit 2~Bit33 : 4-byte ID Number ● Bit 34 : Odd Parity (bit 18 ~ bit 33) ● p.13... -
Page 17: Rs-232 Output
RS-232 output Output waveform Data type START (0X02H) DATA (10 Char) END (0x03H) START(0X02H) DATA (10 Char) END (0x03H) Check the following settings: Baud Rate : 9600bps Data Bit : 8 Parity Bit : None Stop Bit : 1 LRC: This is the result of XOR operation of each byte from Start to End. p.14 Output format... -
Page 18: 8 Bit Burst Output Format
8 bit burst output format 8 bit burst output format Keypads Binary Hexa Keypads Binary Hexa 11110000 10010110 11100001 10000111 11010010 01111000 11000011 01101001 10110100 01011010 10100101 01001011 Output format p.15... -
Page 19: Troubleshooting
Troubleshooting Troubleshooting If the product does not function properly, please see the below for trouble shooting. Problem Solution My card is not read 1) Check the rated voltage specified in the user manual and the catalog. properly. 2) Ensure that you are using an ISO14443 Type A card. - Cards of 125 kHz format can not be used. - Page 20 Problem Solution 2) If you encounter a different read range for each card that is made by the same manufacturer, please contact the nearest customer service. Troubleshooting p.17...
-
Page 21: Product Specifications
Product specifications Product specifications Item SRK101-V Power / Current DC 12V / Max.150mA Reading Time (Card) 30ms Input Port 2ea : External LED Control, External Buzzer Control Output Port 34bit Wiegand, 8bit Burst for PIN LED Indicator 3 LED Indicators (Red, Green and Orange) Beeper Piezo Buzzer Keypad...