Safety Instructions - Makita 9227C Operating Instructions Manual

ENGLISH
1 Protrusion of loop handle
2 Matching hole in gear housing
3 Shaft lock
4 Loop handle
5 Bolts
6 Hex wrench
7 Wool pad
8 Sleeve 18

SAFETY INSTRUCTIONS

Warning! When using electric tools, basic safety
precautions should always be followed to reduce
the risk of fire, electric shock and personal injury,
including the following.
Read all these instructions before attempting to
operate this product and save these instructions.
For safe operation:
1. Keep work area clean
Cluttered areas and benches invite injuries.
2. Consider work area environment
Don't expose power tools to rain. Don't use power
tools in damp or wet locations. Keep work area
well lit. Don't use power tools in presence of
flammable liquids or gases.
3. Guard against electric shock
Prevent body contact with grounded surfaces
(e.g. pipes, radiators, ranges, refrigerators).
4. Keep children away
Do not let visitors contact tool or extension cord.
All visitors should be kept away from work area.
5. Store idle tools
When not in use, tools should be stored in dry,
high, or locked-up place, out of the reach of
children.
6. Don't force tool
It will do the job better and safer at the rate for
which it was intended.
7. Use right tool
Don't force small tools or attachments to do the
job of a heavy duty tool. Don't use tools for
purposes not intended; for example, don't use
circular saw for cutting tree limbs or logs.
8. Dress properly
Do not wear loose clothing or jewelry. They can be
caught in moving parts. Rubber gloves and non-
skid footwear are recommended when working
outdoors. Wear protective hair covering to contain
long hair.
9. Use safety glasses and hearing protection
Also use face or dust mask if cutting operation is
dusty.
10. Connect dust extraction equipment
If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used.
Explanation of general view
9 Backing pad
10 Spindle
11 Press
12 Wool bonnet
13 Lock nut
14 Rubber pad
15 Lock nut wrench
16 Loosen
11. Don't abuse cord
12. Secure work
13. Don't overreach
14. Maintain tools with care
15. Disconnect tools
16. Remove adjusting keys and wrenches
17. Avoid unintentional starting
18. Outdoor use extension cords
19. Stay alert
20. Check damaged parts
4
17 Tighten
18 Switch trigger
19 Lock button
20 Speed adjusting dial
21 Abrasive disc
22 Limit mark
23 Screwdriver
24 Brush holder cap
Never carry tool by cord or yank it to disconnect it
from receptacle. Keep cord from heat, oil and
sharp edges.
Use clamps or a vise to hold work. It's safer than
using your hand and it frees both hands to operate
tool.
Keep proper footing and balance at all times.
Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating
and changing accessories. Inspect tool cords
periodically and, if damaged, have repaired by
authorized service facility. Inspect extension cords
periodically and replace if damaged. Keep
handles dry, clean and free from oil and grease.
When not in use, before servicing, and when
changing accessories such as blades, bits and
cutters.
Form the habit of checking to see that keys and
adjusting wrenches are removed from tool before
turning it on.
Don't carry plugged-in tool with finger on switch.
Be sure switch is off when plugging in.
When tool is used outdoors, use only extension
cords intended for use outdoors and so marked.
Watch what you are doing. Use common sense.
Do not operate tool when you are tired.
Before further use of the tool, a guard or other part
that is damaged should be carefully checked to
determine that it will operate properly and perform
its intended function. Check for alignment of mov-
ing parts, binding of moving parts, breakage of
parts, mounting, and any other conditions that
may affect its operation. A guard or other part that
is damaged should be properly repaired or
replaced by an authorized service center unless
otherwise indicated elsewhere in this instruction
manual. Have defective switches replaced by and
authorized service center. Do not use tool if switch
does not turn it on and off.