Table of Contents
Advertisement
Commercial Ice Machine
VPIM55/85
VPIM280
Valpro Commercial Refrigeration
5256 EagleTrail Drive Tampa, Florida 33634
Email: info@valpromail.com
http://www.valprorefrigeration.com
User's Manual
Model: VPIM55/85/280
Be sure the ice machine has been standing upright
for at least 24 hours prior to plug-in.
Advertisement
Table of Contents
Related Manuals for VALPRO VPIM55
Summary of Contents for VALPRO VPIM55
- Page 1 Commercial Ice Machine VPIM55/85 VPIM280 Valpro Commercial Refrigeration 5256 EagleTrail Drive Tampa, Florida 33634 Email: info@valpromail.com http://www.valprorefrigeration.com User’s Manual Model: VPIM55/85/280 Be sure the ice machine has been standing upright for at least 24 hours prior to plug-in.
-
Page 2: Probable Correction
Service and Installation Manual Problem Possible Cause Probable Correction The feet are not leveled. See Leveling the Ice Maker. Noise during operation Certain sounds are normal. See Normal Sounds. Reconnected the power The electricity is off. The icemaker supply line. stops suddenly Cut off the electricity;... -
Page 3: Table Of Contents
Service and Installation Manual TABLE OF CONTENTS Troubleshooting ICE MAKER SAFETY………………………....……………………..1 Before Calling for Service If the unit appears to be malfunctioning, read through the OPERATION section IMPORTANT SAFEGUARDS…………………………....………...2 of this manual first. If the problem persists, check the Troubleshooting Guide TECHNICAL INFORMATION………………………....……………5 below and on the following page. -
Page 4: Ice Maker Safety
Service and Installation Manual Service and Installation Manual When this LED is on, the unit is working in the cleaning mode. ICE MAKER SAFETY 6. Cleaning Recommended (White) LED: Cleaning Recommended indicator our safety and the safety of others are very important. light We have provided many important safety messages in this manual and on your When this LED is on green shows the water filter work well. -
Page 5: Important Safeguards
Service and Installation Manual Service and Installation Manual on. If you want to restart the ice-making process after cleaning, press the IMPORTANT SAFEGUARDS ICE button directly more than 3 seconds and the ice machine will Before the ice maker is used, it must be properly positioned automatically go into the ice-making process. - Page 6 Service and Installation Manual Service and Installation Manual an area protected from the elements, such as wind, rain, water spray or drips. Control Panel (located at middle of front bottom louver panel) The ice maker should not be located next to ovens, grills or other sources of •...
-
Page 7: Save These Instructions
Service and Installation Manual Service and Installation Manual light. Others LEDs will be off (Except the cleaning recommended indicator SAVE THESE INSTRUCTIONS light). 14. If you want to make ice cubes after cleaning, press the ICE button to start Electrical Connection the ice –making cycle. -
Page 8: Technical Information
Service and Installation Manual Service and Installation Manual Ice-Making System Cleaning Technical Information Minerals that are removed from water during the freezing cycle will eventually Model VPIM-55 VPIM85 VPIM280 form a hard, scaly deposit in the water system. Cleaning the system regularly 115VAC ~ 60Hz 115VAC ~ 60Hz 115VAC ~ 60Hz... -
Page 9: Component Locations
Service and Installation Manual Service and Installation Manual button to drain completely. Component Locations 6. Perform Water Sprinkler Cleaning procedure as follows. Back view The ice scoop should be washed regularly. Wash it just like any other food Door frame container. -
Page 10: Ice Maker Installation
Service and Installation Manual Service and Installation Manual What should be kept clean There are 4 things to keep clean: Water sprinkler 1. The exterior 2. The interior Water curtain axle 3. Water sprinkler 4. The ice-making system cleaning Silicone plug Drain outlet G3/4"... -
Page 11: Unpacking
Service and Installation Manual Service and Installation Manual Preparing the Ice Cube Machine for Long Storage Unpacking If the ice cube machine will not be used for a long time, or it is to be moved to Remove packaging materials another place, it will be necessary to drain the system of water. - Page 12 Service and Installation Manual Service and Installation Manual Installation clearance Evaporator Top view Side view 5 " Water Rear 5 " pump Water Hot gas valve tank (trough) Compressor Condenser motor 5 " 5 " Front To ensure proper ventilation for your ice maker, the front of the unit must be •...
-
Page 13: Electrical Requirements
Service and Installation Manual Service and Installation Manual Ice-making stage Ice harvest stage Bin full stage IT IS STRONGLY RECOMMENDED TO USE A WATER FILTER. A • IMPORTANT: FILTER, IF IT IS OF THE PROPER TYPE, CAN REMOVE TASTE AND Although the unit has been tested and cleaned at the factory, due to long-term •... -
Page 14: Leveling The Ice Maker
Service and Installation Manual Service and Installation Manual NOTICE: recommended that a separate circuit, serving only your ice maker, be provided. Use receptacles that cannot be turned off by a switch or pull chain. The fuse (or 1. The cleaning recommended indicator light will change from green, yellow circuit breaker) size should be 15 amperes. -
Page 15: Setting Initial Data Of Water Filter
Service and Installation Manual Service and Installation Manual Operation Final Check List before Operation 1. Have all packing materials and tape been removed from the interior and exterior of the ice maker? 2. Did you clean the ice storage bin? (See pages 19 - 23) 3. - Page 16 Service and Installation Manual Service and Installation Manual Water Supply Installation Types The water supply should be ready at the point of installation. The water supply This ice cube machine has been designed to be enclosed (as under a cabinet). It pressure should be a minimum of 20 psig with a static pressure not more than can also be free-standing or built-in (sealed to the floor).
Need help?
Do you have a question about the VPIM55 and is the answer not in the manual?
Questions and answers
Plug in ice maker and pump Turns on and Stand by button blinks no buttons let me change the pump