Marco Beverage Systems filtro Operating And Maintenance Instructions

Auto-fill jug, flask & mini-flask versions

Advertisement

Quick Links

OPERATING AND MAINTANANCE INSTRUCTIONS
Auto-Fill Jug, Flask & Mini-Flask Versions
- (Jug - Dual Hot plate) 1000619; (Mini-flask) 1000622

INTRODUCTION

The information provided in this manual is intended to assist in the installation and
Maintenance of the Auto-Fill Filtro Filter coffee Brewer. Please read the instructions
carefully to prevent accidents and ensure an efficient installation.
This manual is not a substitute for any safety instructions or technical data affixed to the
machine or its packaging. All information in this manual is current at the time of
publication and is subject to change without notice.
Only technicians or authorised service providers should carry out maintenance of these
machines.
The company accepts no responsibility for any damage or injury caused by incorrect or
unreasonable installation and operation.

SAFETY INSTRUCTIONS

·
Read and keep these instructions.
·
To protect against electric shock do not immerse mains cord in water or other
liquid.
·
To prevent chafing of the cable, do not let the mains cord hang over the edge of a
table or counter; or touch hot surfaces.
·
Do not operate any product with a damaged cord, plugs, or after the machine
malfunctions or has been damaged in any manner. If the supply cord is damaged,
it must be replaced by the manufacturer or approved service agent in order to
avoid a hazard.
·
Switch off at the mains (unplug or disconnect from outlet). Allow to cool before
removing components.
·
The use of non-approved spares and/or accessories may cause damage and/or
injuries.
·
Do not use outdoors.
·
Do not use the product for anything other than its intended use.
·
Keep the outside of the coffee maker clean and dry at all times.

DURING OPERATION

!
Allow time for all the coffee to drain from the filter bowl before removing.
!
Protect the controls against grease and dirt.
!
Never use warm or hot water to fill the machine.
!
Risk of scalding. Beware of removing the filter basket/jug/flask when the
brewer is in operation. ALL users of this machine should be trained and should
be aware that the machine dispenses very hot beverages.
!
Do not place an empty glass jug on a hotplate when it is switched on except
immediately before brewing.
1900076
FILTRO
- P/N: (Jug) 1000617 ; (Flask) 1000618;
REV.1
Page 1 of 4

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the filtro and is the answer not in the manual?

Questions and answers

Summary of Contents for Marco Beverage Systems filtro

  • Page 1 INTRODUCTION The information provided in this manual is intended to assist in the installation and maintenance of the Auto-Fill Filtro Filter coffee Brewer. Please read the instructions carefully to prevent accidents and ensure an efficient installation. This manual is not a substitute for any safety instructions or technical data affixed to the machine or its packaging.
  • Page 2 TECHNICAL DETAILS Model Auto-Fill Jug Auto-Fill Flask 1000617 1000618 Supply voltage 230V 230V Frequency 50Hz 50Hz Power 2400W 2200W Dimensions 220x385x460 220x385x615 [WxDxH] mm [WxDxH] mm Empty Weight 6.8kg 7.8kg Capacity (per hr) Brew time 5 min 6.5 min Brew capacity 1.8L 2.2L INSTALLATION...
  • Page 3 OPERATION PRIMING This machine is self priming once it is connected to a mains water supply and turned on. N.B. An amount of water will always remain in the machine and this should be considered when moving the machine or leaving the machine unused for long periods. BREWING COFFEE ·...
  • Page 4 The coffee deposits in the coffee jugs/flasks and the filter can be cleaned with a suitable Jug/Urn Cleanser. The Filtro is designed with a spray head which can be easily removed by hand for cleaning or de-scaling - the bayonet type of fixing can be simply twisted in and out of position.

Table of Contents