Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Jet JCT-1600
- Page 1 Pneumatic Sand Rammer #550600, JCT-1600 #550601, JCT-1601 #550602, JCT-1602 #550603, JCT-1603 #550604, JCT-1604 #550605, JCT-1605 JCT-1605 JCT-1600 Operation & Parts Manual M-550600 Edition 2 05/2017 427 New Sanford Road LaVergne, TN 37086 Ph.: 800-274-6848 www.jettools.com Copyright © 2017 JET...
-
Page 2: Safety Warnings
10. The air tool must be properly lubricated before operating. Do not use this tool for other than its intended use. If used for other purposes, JET disclaims 11. Never start a percussion type air tool (chipper, any real or implied warranty and holds itself breaker, buster, etc.) without securing the... - Page 3 • Use common sense: Avoid prolonged 33. Do not lubricate the tool with combustible use of the sand rammer, and take breaks liquids, such as kerosene, diesel or jet fuel. when needed, especially if symptoms of fatigue, numbness excessive 34.
-
Page 4: About This Manual
As with any tool operation, safety of operator and bystanders should be first priority. If there are questions or comments, please contact your local supplier or JET. JET can also be reached at our web site: www.jettools.com. -
Page 5: Tool Specifications
Specifications were current at time of publication, but because of our policy of continuous improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring obligations. - Page 6 41-47/64~47-5/8 in. 42-1/2~49-1/4 in. Housing material steel steel steel Net weight 8.27 lb. (3.75 kg) 17.64 lb. (8 kg) 21.58 lb. (9.79 kg) Shipping weight 9.27 lb. (4.2 kg) 19 lb. (8.6 kg) 23.5 lb. (10.7 kg) JCT-1600 series Sand Rammers...
-
Page 7: Setup And Assembly
Add a leader hose and install any quick- change couplings farther down the line. Any missing parts or damage should be reported ® immediately to your JET distributor. Do not use a Assume balanced position with your feet damaged tool. Read this instruction manual clear of the butt. -
Page 8: User Maintenance
Tool Pressure Air system requirements JET Air Tools operate on 70-to-100 psi (pounds Use proper air hose size (refer to tool per square inch) air pressure measured at the tool specifications). The hose should be just long when the tool is operating. - Page 9 Use a light oil containing rust inhibitors, such as When using multiple hoses, air hoses should be SAE #10. Many JET air tools have integral oil larger than leader hose. Join multiple hoses reservoirs, which should be kept filled when in-line directly, rather than with quick connect fittings oilers are not used.
- Page 10 Troubleshooting JCT-1600 series Sand Rammers Any disassembly of the tool should be done by qualified service personnel. For problems not addressed below, contact JET technical service at 800-274-6846. Problem Possible cause Remedy Tool will not start. Air valve closed or obstructed.
-
Page 11: Replacement Parts
Non-proprietary parts, such as fasteners, can be found at local hardware stores, or may be ordered from JET. Some parts are shown for reference only, and may not be available individually. - Page 12 #550600, JCT-1600 Benchtop Sand Rammer Index Part No. Description Index Part No. Description JCT1600-01 Butt 1-11/16 in. 12 JCT1600-12 Main valve JCT1600-02 Clamp nut 13 JCT1600-13 Main valve case JCT1600-03 Lock nut 14 JCT1600-14 Valve seat JCT1600-04 Leather ring 15 JCT1600-15...
- Page 13 #550601, JCT-1601 Benchtop Sand Rammer Index Part No. Description Index Part No. Description JCT1601-01 Butt 13 JCT1601-13 Valve JCT1601-02 Clamp nut 14 JCT1601-14 Valve seat JCT1601-03 Lock nut 16 JCT1601-16 Handle body JCT1601-04 Piston bushing 17 130604022 Spring pin 4x22mm JCT1601-05 Leather ring 18 JCT1601-18...
- Page 14 10 JCT1602-10 Lock nut 23 JCT1602-23 Throttle lever 11 JCT1602-11 Front valve seat 24 JCT1602-24 Lever 12 JCT1602-12 Valve pin 6x29.8mm 25 JCT1601-24 Coupling 3/8in. PT JCT1602-RPK, Repair Kit, contains #1,4,5(5),6,18,19,20,21 JCT1602-RBK, Rebuild Kit, contains #11,12(2),13,14 JCT-1600 series Sand Rammers...
- Page 15 #550603, JCT-1603 Floor Sand Rammer Index Part No. Description Index Part No. Description JCT1601-01 Butt 14 JCT1601-14 Valve seat JCT1601-02 Clamp nut JCT1603-HA Handle Assembly (#15-22) JCT1601-03 Lock nut 15 JCT1603-15 Throttle lever JCT1601-04 Piston bushing 16 JCT1603-16 Handle body JCT1601-05 Leather ring 17 130604022...
- Page 16 11 JCT1602-11 Front valve seat 23 JCT1604-23 Coupling M24 12 JCT1602-12 Valve pin 6x29.8mm 24 JCT1604-24 Pipe 13 JCT1602-13 Valve 25 JCT1604-25 14 JCT1602-14 Valve seat JCT1604-RPK, Repair Kit, contains #1,4,5(5),6,18,19,20,21 JCT1602-RBK, Rebuild Kit, contains #11,12(2),13,14 JCT-1600 series Sand Rammers...
- Page 17 #550605, JCT-1605 Floor Sand Rammer Index Part No. Description Index Part No. Description JCT1605-01 Butt JCT1604-HA Handle assembly (#15-22) JCT1605-02 Clamp nut 15 JCT1604-15 Throttle lever JCT1605-03 Lock nut 16 JCT1604-16 Handle body JCT1605-04 Piston bushing 16A JCT1604-16A Lever catch JCT1605-05 Leather ring 17 JCT1604-17...
-
Page 18: Warranty And Service
Accessories; Shop Tools; Warehouse & Dock products; Hand Tools; Air Tools NOTE: JET is a division of JPW Industries, Inc. References in this document to JET also apply to JPW Industries, Inc., or any of its successors in interest to the JET brand. - Page 19 This page intentionally left blank.
- Page 20 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.com JCT-1600 series Sand Rammers...