NN-SE284S / NN-SE284B / NN-SE284W 2 DESCRIPTION OF OPERATING SEQUENCE 2.1. Variable power cooking 2.3. Inverter defrost control When the Auto Control feature is selected and the Start pad is tapped: High Voltage Inverter Power Supply (U) controls output power 1.
NN-SE284S / NN-SE284B / NN-SE284W Explanation of the Auto Sensor Cooking process 1. T1 time The total amount of time it takes the microwave oven to switch to T2 time. 2. T2 time When the steam escapes from the cooking...
NN-SE284S / NN-SE284B / NN-SE284W 3 CAUTIONS TO BE OBSERVED WHEN TROUBLESHOOTING Unlike many other appliances, the microwave oven is a high voltage, high current device. Though it is free from danger in ordinary use, extreme care should be taken during repair.
NN-SE284S / NN-SE284B / NN-SE284W WARNING DISCHARGE HIGH VOLATGE 1. This is mandatory. Refer to “measurements and CAPACITORS adjustments” for the location of these switches. For about 30 seconds after the oven is turned off, an 2. When replacing the fuse, confirm that it has the electric charge remains in the high voltage capacitors of the appropriate rating for these models.
NN-SE284S / NN-SE284B / NN-SE284W 4 COMPONENT TEST PROCEDURE 4.3. Magnetron WARNING 1. High voltage is present at the output terminals of the High Voltage Inverter (U) including aluminum heat sink during any cook cycle. Continuity checks can only indicate an open filament or a 2.
NN-SE284S / NN-SE284B / NN-SE284W 4.4. Inverter power supply (U) 5. Program oven at High power for 1 minute and press [Start] pad. DO NOT try to REPAIR H.V. Inverter power supply (U). a. After approximately 3 seconds, oven stops operating.
NN-SE284S / NN-SE284B / NN-SE284W 5 MEASUREMENTS AND ADJUSTMENTS 5.1. Adjustment of primary interlock switch, secondary interlock switch and interlock monitor switch. 1. Mount the Primary Interlock Switch, the Secondary Interlock 5.2. Measurement of microwave Switch and the Interlock Monitor Switch to the door hook output assembly as shown in illustration.
NN-SE284S / NN-SE284B / NN-SE284W 6 PROCEDURE FOR MEASURING MICROWAVE ENERGY LEAKAGE 6.2.1. Measurement with the outer panel removed. Whenever you replace the magnetron, measure for radiation leakage before the outer panel is installed and after all necessary components are replaced or adjusted. Special care should be taken in measuring around the magnetron.
NN-SE284S / NN-SE284B / NN-SE284W 7 TROUBLESHOOTING GUIDE DANGER: HIGH VOLTAGES 1. DO NOT RE-ADJUST PRESET CONTROL on the H.V.Inverter (U). It is very dangerous to repair or adjust without proper test equipment because this circuit generates very large current and high voltage. Operating a misaligned inverter circuit is dangerous.
NN-SE284S / NN-SE284B / NN-SE284W 7.1. (Troubleshooting) Oven stops operation during cooking SYMPTOM CAUSE CORRECTIONS 1. Oven stops 3 seconds after No 120V AC is supplied to H.V.Inverter (U) CN702 1. Interlock Switch pressing [Start] pad terminals 2. Power relay RY1 3.
NN-SE284S / NN-SE284B / NN-SE284W 7.2. (Troubleshooting) Other problems SYMPTOM CAUSE CORRECTIONS 1. Oven is dead. 1. Open or loose lead wire harness Fuse is OK. 2. Open thermal cutout / thermistor Check thermal cutout is defective. No display and no operation at all.
NN-SE284S / NN-SE284B / NN-SE284W 7.3. Trouble related to Digital Programmer Circuit SYMPTOM STEP CHECK RESULT CAUSE/CORRECTIONS →Step2 No display when oven is first plugged Fuse pattern of D.P.C. Normal Open Replace D.P.C. or Fuse Pattern Low voltage transforment (L.V.T.) Abnormal 0V L.V.T.
NN-SE284S / NN-SE284B / NN-SE284W 7.4. Troubleshooting of inverter circuit (U) and magnetron This oven is programmed with a self diagnostics failure code system which will help for troubleshooting. H95, H97, H98 and H99 are the provided failure codes to indicate magnetron and inverter circuit problem areas. This section explains failure codes of H95, H97, H98 and H99.
NN-SE284S / NN-SE284B / NN-SE284W 7.5. SIMPLE WAY OF H.V. INVERTER/MAGNETRON TROUBLESHOOTING Purpose: Simple way (3/23 seconds rule) of identifying whether it’s Magnetron, Inverter or others. Set-up: The unit under question is connected through the Ammeter as shown below. Procedure: Follow the matrix table below to identify the problem source.
NN-SE284S / NN-SE284B / NN-SE284W 8.2. PARTS LIST NOTE: 1. When ordering replacement part(s), please use part number(s) shown in this part list. Do not use description of the part. 2. Important safety notice: Components identified by mark have special characteristics important for safety.
NN-SE284S / NN-SE284B / NN-SE284W 8.3. DOOR ASSEMBLY Ref. No. Part No. Part Name & Description Pcs/Set Remarks F30186P40AG DOOR KEY A F302ABL60SCP DOOR A (U) SE284S F302ABL70BCP DOOR A (U) SE284B F302ABL70HCP DOOR A (U) SE284W F302K5H00AP DOOR E (U)