NN-SE995S / NN-SD985S / NN-ST965S 2 DESCRIPTION OF OPERATING SEQUENCE 2.1. Variable power cooking 2.3. Inverter defrost control When the Auto Control feature is selected and the Start pad is tapped: High Voltage Inverter Power Supply (U) controls output power 1.
NN-SE995S / NN-SD985S / NN-ST965S Explanation of the Auto Sensor Cooking process NOTE: 1. During the first 10 second period there is no microwave When "More" or "Less" pad is selected, the K factor varies activity. When calculating the T2 time by using the resulting in T2 time to be increased or decreased.
NN-SE995S / NN-SD985S / NN-ST965S 3 CAUTIONS TO BE OBSERVED WHEN TROUBLESHOOTING Unlike many other appliances, the microwave oven is a high voltage, high current device. It is free from danger in ordinary use, though extreme care should be taken during repair.
NN-SE995S / NN-SD985S / NN-ST965S Discharging the high voltage capacitors 3.6. Verification after repair WARNING 1. After repair or replacement of parts, make sure that the There is high voltage present with high current capabilities screws of the oven, etc. are neither loosen or missing.
NN-SE995S / NN-SD985S / NN-ST965S 4 DISASSEMBLY AND PARTS REPLACEMENT PROCEDURE 4.1. Magnetron 4.2. Digital programmer circuit (D.P.C) 1. Discharge high voltage charge. 2. Remove 1 screw holding air guide A on the oven cavity. CAUTION: 3. Remove 1 screw holding air guide B.
NN-SE995S / NN-SD985S / NN-ST965S 4.3. Low voltage transformer 4.5. Door assembly and/or power relays RL1 1. Remove door C from door E by carefully pulling outward, starting from upper right hand corner using a flat blade CAUTION: screwdriver. Be sure to ground any static electric charge built up in 2.
NN-SE995S / NN-SD985S / NN-ST965S 4.6. Turntable motor 4.7. Steam sensor 1. Remove the motor cover by breaking off at the 8 spots 1. Disconnect connector CN2 from digital programmer circuit indicated by arrows with a cutter or the like.
NN-SE995S / NN-SD985S / NN-ST965S 4.8. Inverter power supply 6. Press 1 encircled locking tab and then slide 4 locking tabs of Inverter bracket at the bottom of the base in direction of CAUTIONS arrows. 1. Always leave the grounding plate in place.
NN-SE995S / NN-SD985S / NN-ST965S 5 COMPONENT TEST PROCEDURE 5.3. Magnetron WARNING 1. High voltage is present at the output terminals of the High Voltage Inverter (U) including aluminum heat sink during any cook cycle. Continuity checks can only indicate an open filament or a 2.
NN-SE995S / NN-SD985S / NN-ST965S 5.4. Inverter power supply (U) 4. Program DPC. For SD985S model DO NOT try to REPAIR H.V. Inverter power supply (U). a. Press Timer/Clock button twice. Replace complete H.V. Inverter(U) Unit. b. Press Start button once.
NN-SE995S / NN-SD985S / NN-ST965S 6 MEASUREMENTS AND ADJUSTMENTS 6.1. Adjustment of primary interlock switch, secondary interlock switch and interlock monitor switch. 1. Mount the Primary Interlock Switch, the Secondary Interlock 6.2. Measurement of microwave Switch and the Interlock Monitor Switch to the door hook output assembly as shown in illustration.
NN-SE995S / NN-SD985S / NN-ST965S 7 PROCEDURE FOR MEASURING MICROWAVE ENERGY LEAKAGE 7.2.1. Measurement with the outer panel removed. Whenever you replace the magnetron, measure for radiation leakage before the outer panel is installed and after all necessary components are replaced or adjusted. Special care should be taken in measuring around the magnetron.
NN-SE995S / NN-SD985S / NN-ST965S 8 TROUBLESHOOTING GUIDE DANGER: HIGH VOLTAGES 1. DO NOT RE-ADJUST PRESET CONTROL on the H.V.Inverter (U). It is very dangerous to repair or adjust without proper test equipment because this circuit generates very large current and high voltage. Operating a misaligned inverter circuit is dangerous.
NN-SE995S / NN-SD985S / NN-ST965S 8.1. (Troubleshooting) Oven stops operation during cooking SYMPTOM CAUSE CORRECTIONS 1. Oven stops in 3 seconds after No 120V AC is supplied to H.V.Inverter (U) 1. Interlock Switch pressing [Start] pad (button) CN702 terminals 2. Power relay RL1 3.
NN-SE995S / NN-SD985S / NN-ST965S 8.2. (Troubleshooting) Other problems SYMPTOM CAUSE CORRECTIONS 1. Oven is dead. 1. Open or loose lead wire harness Fuse is OK. 2. Open thermal cutout / thermistor Check thermal cutout is defective. No display and no operation at all.
H97, H98 and H99. First, you must program the DPC into TEST MODE, For NN-SE995S, ST965S models: press Clock button once → press Timer button once → press Start button once → press Power Level button once, For NN-SD985S model: press Timer/Clock button twice →...
NN-SE995S / NN-SD985S / NN-ST965S 8.4. Trouble related to Digital Programmer Circuit 8.4.1. NN-SE995S SYMPTOM STEP CHECK RESULT CAUSE/CORRECTIONS →Step2 No display when oven is first plugged Fuse pattern of D.P.C. Normal Open Replace D.P.C. or Fuse Pattern Low voltage transforment (L.V.T.) Abnormal 0V L.V.T.
Page 24
NN-SE995S / NN-SD985S / NN-ST965S 8.4.2. NN-ST965S SYMPTOM STEP CHECK RESULT CAUSE/CORRECTIONS →Step2 No display when oven is first plugged Fuse pattern of D.P.C. Normal Open Replace D.P.C. or Fuse Pattern Low voltage transforment (L.V.T.) Abnormal 0V L.V.T. secondary voltage →Step3...
Page 25
NN-SE995S / NN-SD985S / NN-ST965S 8.4.3. NN-SD985S SYMPTOM STEP CHECK RESULT CAUSE/CORRECTIONS →Step2 No display when oven is first plugged Fuse pattern of D.P.C. Normal Open Replace D.P.C. or Fuse Pattern Low voltage transforment (L.V.T.) Abnormal 0V L.V.T. secondary voltage →Step3...
NN-SE995S / NN-SD985S / NN-ST965S 8.5. SIMPLE WAY OF H.V. INVERTER/MAGNETRON TROUBLESHOOTING Purpose: Simple way (3/23 seconds rule) of identifying whether it’s Magnetron, Inverter or others. Set-up: The unit under question is connected through the Ammeter as shown below. Procedure: Follow the matrix table below to identify the problem source.
NN-SE995S / NN-SD985S / NN-ST965S 9.2. PARTS LIST NOTE: 1. When ordering replacement part(s), please use part number(s) shown in this part list. Do not use description of the part. 2. Important safety notice: Components identified by mark have special characteristics important for safety.
Page 30
NN-SE995S / NN-SD985S / NN-ST965S Ref. No. Part No. Part Name & Description Pcs/Set Remarks F04467D00RP FUNCTION LABEL SD985S F0445BP20AP PICTO LABEL SE995S F0007BP30SRP NAME PLATE SE995S F0007BP10SRP NAME PLATE SD985S F0007BQ40SRP NAME PLATE ST965S...
NN-SE995S / NN-SD985S / NN-ST965S 9.4. DOOR ASSEMBLY Ref. No. Part No. Part Name & Description Pcs/Set Remarks F30186P40AG DOOR KEY A F302ABP30SAP DOOR A (U) SE995S F302ABP10SRP DOOR A (U) SD985S F302ABQ50SAP DOOR A (U) ST965S F302KBK10AP DOOR E (U)