1. Manuals
  2. Brands
  3. iVision Manuals
  4. Security Camera
  5. IV-WP866PL
  6. User manual

iVision IV-WP866PL User Manual

Ir low speed dome camera
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
IR Low Speed Dome Camera
User's Manual
●
●
Please read the manual carefully before installing and using the unit.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IV-WP866PL and is the answer not in the manual?

Questions and answers

Related Manuals for iVision IV-WP866PL

Summary of Contents for iVision IV-WP866PL

  • Page 1 IR Low Speed Dome Camera User’s Manual ● ● Please read the manual carefully before installing and using the unit.

  • Page 2: Table Of Contents

    Table of the Contents I. Introduction………………………………………………………………..……………………….………………………………..……………………….. 3 II. Technical Data…………………………………………………………..…………………………………..……………………….……………………….3 III. Characteristics……………………………………………………………..……………………………………………………..……………………….….8 IV. Description of Functions……………………………………………………………………………………..……………………….…..………………..8 V. Installation and Connection of the Device……………………………………………………………………..……………………….……..………….11 ………………………………..………………………. 5.1 Outer-shape and Dimension………………………………………………… ……………………………………11 ………………………………..………………………. 5.2 Preparation for the Installation……………………………………………………………… ..………….…..11 ………………………………..………………………. 5.3 Installation of Wall-mount IR Low-speed Dome Camera………………………………………. ….………..11 ………………………………..……………………….

  • Page 3: Important Safeguards

    Important Safeguards 1. During the course of transportation and storage, the product should be avoided from incorrect operations such as heavy pressing, strong vibration, soaking etc, which may cause damage to the unit. 2. The product is designed for Wall-mount and Pendant-mount installation, so it can not be installed upside-down. And the module should be handled properly so as not to bring about mechanical problems affecting the integrative functions of it.

  • Page 4: I. Introduction

    I. Introduction Adopting latest technological achievements and cutting-edge manufacturing techniques, the IR Low-speed Dome Camera is created with many years of accumulated experience. Equiped with a high performance DSP camera module with zooming lens, integrating built-in Pan/tilt and digital decoder, it represents the future trend of hi-tech monitoring products.
  • Page 5 2.2 Specification for camera modules optional (4 types Available): Item JCO- 4481 Image sensor 1/4 inch Exview HAD CCD Horizental resolution 480TVL Signal system Zomm ratio 22X Optical Focal length 3.9~85.8mm IR feature Electronic dual light-filter, day&night Color 0.2LUX/ Min. Illumination B&W 0.05LUX S/N ratio ≥48dB...
  • Page 6 Item JCO- 4B22 Image sensor 1/4 inch SONY HAD CCD Horizental resolution 480TVL Signal system 22X Optical Zomm ratio 16X Digital Focal length 3.9~85.8mm IR feature Dual light-filter, day&night: auto-switch, switch linkage Color 0.12LUX/ Min. Illumination B&W 0.05LUX S/N ratio ≥48dB Synchronization Internal...
  • Page 7 Item JCO- 4C22 1/4" Super HAD Image sensor CCD II Horizental resolution 540TVL Signal system 22X Optical Zomm ratio 12X Digital Focal length 3.3~73mm IR feature Dual light-filter, day&night: auto-switch, switch linkage Color 0.3LUX/ Min. Illumination B&W 0.05LUX S/N ratio ≥50dB Synchronization internal/external...
  • Page 8 JCO- 4B35 Item Image sensor 1/4 inch Exview HAD CCD Horizental resolution 480TVL Signal system 35X Optical Zomm ratio 16X Digital Focal length 3.6~126mm IR feature Dual light-filter, day&night: auto-switch, switch linkage Color 0.12LUX/ Min. Illumination B&W 0.05LUX S/N ratio ≥48dB Synchronization Internal...

  • Page 9: Iii. Characteristics

    III. Characteristics  Latest LED Array technology adopted for IR lamps, LED Array has higher brightness, longer visible distance (over 150m), more evenly distributed light field and much longer lifespan.  In-built module programme can automatically identify multiple brands of camera modules including LG, SONY, HITACHI, CNB etc.
  • Page 10 through adjusting the focal length. In the default Auto-focus, Auto Iris state, following the movement of the pan/tilt, the lens will quickly adjust itself to get clear image according to the change of the object. 3. Automatic Adjustment of Focal Length/Movement Speed When the focus is long and the unit is in under manual operation, due to the high sensitivity of the IR Low-speed Dome Camera, even the slightest movement of the joystick would make the image move quickly, which causes image losses.
  • Page 11 Users can adjust the Focal-length through controlling the keyboard to get panoramic view or close view that they desire. Focus Control The system takes auto-focus as the default. While moving, the camera module can automatically focus on the center of the object view to get clear image. Under special circumstances, the user can manually adjust the focus to achieve desired image effect.

  • Page 12: Preparation For The Installation

    V. Installation and Connection of the device 5.1 Outer-shape and Dimension 5.2 Preparation for the Installation: 1. To avoid mistakes, installation must be done by qualified personnel conforming to related regulations. 2. Please check whether the attachments are all ready, and whether the installing location and style of installation are compatible.
  • Page 13 Wall Bracket Installation Dimensions B. Use an electrical drill to make four holes for M6 screws on the above-drawn positions, and drive in the expansion M6 screws; C．Fix the installation board of the bracket firmly on the wall with four M6 screw nuts and washers. D.
  • Page 14 Attention: The adaptor equiped can only be placed indoor or in water-proof box or other water-proof spaces, it can not be placed directly outdoor, otherwise water may seep in and damage the adaptor. F. Put up the wall bracket assembled with IR Low-speed dome on the ancillary hooks: Pull the power cable, video cable and controlling cable out through the wire-out-going hole of the bracket, then put the assembled on the two corresponding pegs on the installed peg-board, then push the bracket downward until it locks in place.

  • Page 15: Installation Of Pendant-Mount Ir Low-Speed Dome Camera

    c Use controlling device to control the IR Low-speed Dome Camera, checking whether it can perform the functions of the pan/tilt and the lens of the camera module. If not, please check the configuration of communication protocol, Baud rate and address, and the connection of 485 controlling cable. 5.4 Installation of Pendant-mount IR Low-speed Dome Camera 5.4.1 Installation of Pendant-mount Bracket Remarks: The ceiling for the selected installation location must be firm without peeling.

  • Page 16: Vi. Configure The System Of The Ir Low-Speed Dome Camera

    ---monitoring device negative Earth Connecting IR Low-speed dome Black cable connecting earth --- the earth port lightening proof When connecting, make sure the polarity of RS485 controlling cable is correct: A: RS485 positive, B: RS485 ◆ negative. If wrongly connected, the IR Low-speed Dome Camera will be out of control. ◆...

  • Page 17: Configure Baud Rate

    PELCO_D1 If the controlling device could only support the preset position numbers below 128, please use PELCO_D1 controlling protocol. 6.2 Configure Baud Rate DIP-3 and DIP-4 of the 4-button switch on the PCB board is used to configure Baudrate of communication, the default configuration is 4800BPS.
  • Page 18 00010111 00110110 01010101 00011000 00110111 01010110 00011001 00111000 01010111 00011010 00111001 01011000 00011011 00111010 01011001 00011100 00111011 01011010 00011101 00111100 01011011 00011110 00111101 01011100 00011111 00111110 01011101 87654321 87654321 87654321 01011110 01111101 10011100 01011111 01111110 10011101 01100000 01111111 10011110 01100001 10000000 10011111 01100010...

  • Page 19: Vii. Basic Functions Of The Ir Low-Speed Dome Camera

    11000011 11011010 11110001 11000100 11011011 11110010 11000101 11011100 11110011 11000110 11011101 11110100 11000111 11011110 11110101 11001000 11011111 11110110 11001001 11100000 11110111 11001010 11100001 11111000 11001011 11100010 11111001 11001100 11100011 11111010 11001101 11100100 11111011 11001110 11100101 11111100 11001111 11100110 11111101 11010000 11100111 11111110 11010001...

  • Page 20: Configure And Run Tour Group

    ◆ Manual focus approach can be adopted to configure preset positions for distant objects, that is, after adusting the lens to focus on distant place, control the keys “FOCUS+”and “FOCUS-”on the controlling keyboard to configure optimal focal image storage to avoid fuzzy images resulting from the interference of other distant objects. 7.2.2 Invoke Preset Positions The function enables the IR Low-speed Dome Camera to quickly return to the preset position.

  • Page 21: Configure And Start Left & Right Scan

    functions of the IR Low-speed Dome Camera may be not operational. 7.4 Configure and start Left & Right scan The IR Low-speed Dome Camera has Left/Right scan function. The user can configure the left and right limiting positions for the required left&right scanning area. When running the left&right scan, the unit will scan forwards and backwards between the left and right limiting positions consecutively.

  • Page 22: Configure, Activate And Idle The Default Position Function

    you can operate on the keyboard to stop the auto scan. Operation is as below: Input 138(108) Press PREVIEW key The Auto Scan can also be stopped by any operation on the joystick of the keyboard. 7.7 Configure, Activate and Idle the Default Position function The unit has default position function.

  • Page 23: Viv. Trouble Shooting Table

    Start Left & right scanning Enter menu of the camera Module Start Pan/tilt 360º scanning Exit menu of the camera Module Stop Pan/tilt auto-scanning Activate default position function Start tour configuration Idle default position function Exit tour configuration Configure default position function Start running a tour If preset position numbers larger than 128 could not be invoked on the controlling device, please choose PELCO-D1 protocol, functions operation table as below:...
  • Page 24 image but out of control Protocol configuration wrong Configure again RS485 bus bad connection Check RS485 bus connection Mechanical failure Repair Camera Module inclined Reinstall Abnormal self-check image Power supply not enough Replace, better to place the with motor noise adaptor nearby the IR Low-speed Dome Camera Bad connection of video cable...

Table of Contents