1. Manuals
  2. Brands
  3. Han-Bond Manuals
  4. Cutter
  5. H8-120
  6. User manual

Han-Bond H8-120 User Manual

H8 plus series vertical ink jet cutting machine
Hide thumbs
Table of Contents

Advertisement

Quick Links

www.han-bond.com
Vertical ink jet cutting machine
User manual

Advertisement

Table of Contents
loading

Related Manuals for Han-Bond H8-120

Summary of Contents for Han-Bond H8-120

  • Page 1 Vertical ink jet cutting machine User manual...

  • Page 2: Preface

    Preface Thank you for choosing Han-Bond H8 Plus series vertical ink jet cutting machine. H8 series vertical jet cutting machine unique shape design that is exquisite, the reasonable structure save display space, can be widely used in drawing, cutting large format clothing mark, luggage, engineering drawings, models, graph cut drawing quality reach the international first-class effect.

  • Page 3: Table Of Contents

    Preface............................. 1 catalog............................2 Safety instruction........................5 Matters needing attention...................... 7 Other matters........................7 Basic performance index....................10 Computer system requirements..................11 Chapter 1 assembly....................... 12 1.1 Open box and check components................12 1.2 machine installation....................13 1.3 machine connection....................14 1.3.2 connection USB data line..............14 1.3.1 connection of power cord..............
  • Page 4 1.5.1 assemble and disassemble knife holder ........19 1.5.2 knife holder assemble diagram ............20 1.5.3 The use of knife holder ..............21 1.5.4 Han-bond blade ..................21 1.6 install printing / cutting papers ................22 Chapter 2 installation drive ....................23 2.1load driver (for example : win7 64 bit computer operating system)23...
  • Page 5 5.1 offset calibration ..................... 42 5.1.1 calibration nozzle dislocation ............42 5.1.2 calibration of row spacing dislocation ........43 5.1.3 calibration cartridge tilt misalignment ........44 5.2 precision calibration ....................44 Chapter 6 failure analysis ...................... 53 6.1 control panel error and solution ................53 6.1.1 X encoder error ..................

  • Page 6: Safety Instruction

    Safety instruction Please carefully read all the following instructions before using the vertical jet cutting machine:  Place the machine on the level ground, avoid putting it on an unstable surface caused unnecessary fault.  It is forbidden to connect the machine to the attachment with non rated voltage.
  • Page 7  When you do not use the machine for a long time, pull the plug from the power outlet  Unplug the power plug before cleaning the machine.  Do not drop the liquid into a vertical jet cutting machine, otherwise it will cause the circuit board of the machine to short circuit and destroy the component.

  • Page 8: Matters Needing Attention

    Matters needing attention Although you may be familiar with the H8 series vertical ink jet cutting machine, please read the following carefully before you operating the machine: Machine usage environment  The machine works and storage temperature: 10-35 degrees Celsius, do not store or use it in a strong light irradiation, radiation or heat.
  • Page 9  Before you connect or disconnect the power supply, make sure the machine is in a shutdown state.  When you end the use of machine, please keep the machine with dust cover well to prevent dust from entering.
  • Page 10 Introduction Thank you for choosing Han-bond H8 series vertical ink jet cutting machine. H8 series vertical ink jet cutting all in one machine adopts double feeding paper system (white paper and kraft paper can be loaded at the same time), and can be used to drawing, cutting large format of clothing mark, luggage break the pattern, engineering drawings, model etc., graph cut drawing quality reached the...

  • Page 11: Basic Performance Index

    1800mm 2000mm 2300mm width Loading paper mode Wheel feeding paper , automatic feeding paper (double feeding paper system) Transmission mode Han-Bond printing system+USB2.0 Original coordinate Can self set base point setting Knife standard diameter Cutting material Suitable for a variety of clothing special paper (60-350g)

  • Page 12: Computer System Requirements

    Computer system requirements System Microsoft Windows XP Intel Core i5 Memory hard disk 500G CD-ROM 4 times above CD-ROM USB2.0 port...

  • Page 13: Chapter 1 Assembly

    Chapter 1 assembly 1.1 Open box and check components List of components: main machine x1, tripod beam x1, left foot rack x1, right foot rack x1, universal casters x4, paper collection roller X1 article, send paper drum X2, clutch paper cone x4, paper pressing rod X2, hp45 ink cartridge X2,...

  • Page 14: Machine Installation

    1.2 machine installation Figure 1 machine parts drawing Name of all parts of the machine 1 the right side board 2 left and right foot plate 3 right tripod 4 left tripod 7 ink frame connecting plate 8 H8 slide...

  • Page 15: Machine Connection

    15 Sensor holder 19 idler wheel group 21 collect and press paper bar group 22 paper collection roller group 35 paper feeding motor 36 roller base 44 universal caster 1.3 machine connection 1.3.2 connection USB data line First to turn off the machine power, and the USB data line and machine connection point need to use "can stick type fixed seat"...

  • Page 16: Install Hp45 Cartridge

    1.4 install HP45 cartridge 1.4.1 cartridge type H8 series of vertical jet cutting machine use HP51645 model cartridge, in order to ensure the quality of printing, it is recommended to select the authentic cartridge, HP supplies store sales. 1.4.2 cartridge installation...

  • Page 17: Ink Exhaustion Mark

    1.4.3 ink exhaustion mark The ink of the cartridge during drawing process, the constant consumption; ink exhaust mark will gradually change from green to black; if the mark is changed to black completely, indicating that the cartridge has run out of ink, need to replace the cartridge (see Figure 4).
  • Page 18 1.4.5 cleaning cartridge If the printing graphics have some points or lines not printed (see Figure 5), you need cleaning cartridge.
  • Page 19 B use dry cotton cloth to wipe the ink cartridge side PCB (see Figure 7) to avoid damage to the PCB, should only be wiped once. C To clean nozzle by non-dust cloth or cotton with alcohol(see picture 8,9,10).

  • Page 20: Mounting Tool Holder

    Auto clean Press the "CLEAN" key in the standby mode, the nozzle can be cleaned automatically. 1.5 mounting tool holder 1.5.1 assemble and disassemble knife holder Unscrew the hand nut , then you can pull up.

  • Page 21: Knife Holder Assemble Diagram

    1.5.2 knife holder assemble diagram...

  • Page 22: The Use Of Knife Holder

    250g kraft paper cutting knife, Han-bond can be adjusted to "3" (adjust the blade length of about 0.297 mm). Note: due to the material density of different reasons, blade length adjustable there will be differences, and also with the blade loss degree and machine parameter settings.

  • Page 23: Install Printing / Cutting Papers

    1.6 install printing / cutting papers The print / cut paper instruction: weight: 40-300g, tube diameter 60~75 mm, fiber container quality is less than 50kg. H8 vertical ink jet cutting all in one machine, when the cutting mode is using...

  • Page 24: Chapter 2 Installation Drive

    D disk). Make sure the USB data line to be securely connected on the machine, and turn on the power switch of the machine, the computer will be prompted to "update driver software (Han-Bond Printer)", began to enter the installation process.
  • Page 25 Select "browse the computer to find the driver software (R)" Click “browse"...
  • Page 26 Select the "win7 64" folder in the first step copy path, open the "win7 64" folder that under "win7 64" folder , click “OK” after selected. Click "next"...
  • Page 27 Load in... Click "close" Installation process complete!
  • Page 28 After the successful installation of the Han-Bond Printer driver, turn on the power switch of the machine (the USB data line is in the connected state). Test methods: 'my computer' position with the right mouse button to choose "properties", open the "device manager", in the "universal serial bus controller"...

  • Page 29: Chapter 3 Installation And Use Of The Output Center

    Chapter 3 installation and use of the output center Note: when you select output center installation package, Windows XP, win7 32-bit computer operating system choice running the file "Han-Bond print system 32bit"; win7 64 bit or above computer operating system choice running the file "Han- Bond print system 64bit"!
  • Page 30 Click "next (NEXT)".
  • Page 31 Click "next (NEXT)". Click "Install".
  • Page 32 Installing...
  • Page 33 Install is completed and run Print Center Computer operating system for the installation of win7 64 can refer to the steps of the computer operating system windows XP! But the loaded file that need to select the file "Han-Bond Print System 64bit ".

  • Page 34: The Use Of The Output Center

    3.2 the use of the output center Han-Bond print system is a PC terminal software presented by Han-Bond company, its functions include graphics browsing, printing, as well as graphics editing and text notes, etc.. Before using, be sure to adjust the following settings options! 3.2.1 graphic direction setting...

  • Page 35: Page Settings

    3.2.2 page settings Open the page settings, to confirm that the scaling ratio is 100%. 3.2.3 page header and footer settings Header and footer: do not click the "use header print" and “use footer to print". (usually print clothing marker is not required for headers and footers,...

  • Page 36: Print Segment Length Settings

    3.2.5 print segment length settings When chose cutting function, the segment length is set to 300mm, before debugging pettifoggery coincidence it also needs to set the segment length to 300mm; In the selection of the drawing function, the segment length does not need...

  • Page 37: Print Preview

    3.2.6 Print Preview Open print preview, or click on preview the ready to print graphics. 3.2.7 print output Open the print options or click , and enter the required number of print, and then click OK".

  • Page 38: File Conversion And Save

    3.2.8 file conversion and save Han-Bond print system support Plt. Dwg. Dxf and other types of print file to save as conversion.

  • Page 39: Chapter 4 Control Panel

    Chapter 4 control panel 4.1 control panel The control panel is a human-computer interaction platform vertical spray machine cut, the current state through a liquid crystal display device can understand the machine; on the other hand, it is convenient for the operator to...
  • Page 40 【 】 —— draw back paper 【 】 —— paper feed 【 】 —— Left shift ink box group 【 】 —— right shift ink box group 【 】 —— Cancel the current print job 【 】 —— One key cutting paper function 【...
  • Page 41 Parameter setting check list: Parameter setting Ink jet speed MIDIUM Ink jet head split 0.00 Nozzle coincident 0.00 Row spacing split 0.00 Ink jet speed shift 13000 Row spacing join 0.0mm Nozzle selection Ink jet head selection Ink jet effect...
  • Page 42 Ink jet head maintenance OPEN Tool nose radius 0.00mm Cut paper CLOSED Collect paper motor OPEN Paper type Thick Language English Factory Reset Press OK 3”...

  • Page 43: Chapter 5 Calibration

    Chapter 5 calibration 5.1 offset calibration Shipped along with the machine there is a disk, select PLT test file "1000X1000.PLT" in the disk, and print. 图 7 1000X1000.PLT 5.1.1 calibration nozzle dislocation When the nozzle is dislocation to the right side (Fig. 8), increase parameter value in the 2nd item [nozzle dislocation] parameter, otherwise, decrease the value;...

  • Page 44: Calibration Of Row Spacing Dislocation

    Figure 8 sprinkler head dislocation 5.1.2 calibration of row spacing dislocation If row spacing dislocation is to the right side (for example, figure 9 left), increase the parameter value in the parameter set of 4th item [ spaced dislocation ], contrary to reduce numerical;...

  • Page 45: Calibration Cartridge Tilt Misalignment

    5.1.3 calibration cartridge tilt misalignment Ink box frame’s tilt lean to the left dislocation (FIG. 10 cases, right), tighten the spring adjusting screw on the left of the ink holder. (Before adjustment, the 2 fixed screws on the left of the ink box rack must be all unscrewed) Ink box frame’s tilt lean to the right dislocation (FIG.
  • Page 46 "Han-bond printing system" or "clothing CAD software” to realizing graphic precision correction. To correct "clothing CAD software", please consult the software company, following are the correction method of “Han-Bond printing system"! Note: the same software corresponding to the machine is with same...
  • Page 47 In Han-Bond printing system click "Settings"--> “ option. " Click on the right side of the “paper feeding direction “. Enter the design size and the actual size, and click "confirm"...
  • Page 48 Han-bond printing system automatically help you calculate the compensation coefficient of “feed direction"...
  • Page 49 The setting method of compensation coefficient in the” direction of the car “ is the same as above!!! 5.3 pettifoggery coincidence set Shipped along with the machine there is disk, select test file "H8 pettifoggery coincidence set " in the disk and print,...
  • Page 50 Start debugging pettifoggery coincidence. Note: before the operation, the segment length of the output center must be set to 300 mm Now to analyse the printed and cut file:...
  • Page 51 Figure 11 X/Y coincidence effect diagram ("---black line" is ink jet lines, "red line" is cutting line) Note: all of the following parameters must be adjusted during machine in the standby mode or during ink jet period. If it’s in the parameters of the adjustment during the cutting process are not valid.
  • Page 52 [Y axis coincidence set] the corresponding value, contrary to reduce numerical; Complete the debugging of X, Y axis of the coincidence set Again to print the file "H8 pettifoggery coincidence settings file, start debugging pettifoggery scaling. Note: reference E reference position, after adjusting the X/Y axis coincidence set, then you can to carry out this operation.
  • Page 53 The third step: take (Figure 12) "C reference position" as an example, when the cutting line in the right-hand of ink jet line, reducing the control panel item 18th [X-axis scaling] corresponding value, otherwise to increase the value. The fourth step: take (Figure 12) "D reference position" as an example,...

  • Page 54: Chapter 6 Failure Analysis

    Chapter 6 failure analysis 6.1 control panel error and solution 6.1.1 X encoder error Solution: 1．Check the sensor head in the dolly board and grating ruler’s assembly position, if grating ruler is not in the middle region of sensor groove, need to adjust it well.

  • Page 55: Display "Aaaaaa

    6.1.2 display "AAAAAA" Solution: 1. need password to unlock, please contact the dealer. 6.2 other issues analysis 7．each time to print file, the front section of the print blank or print is not clear, may be the indoor temperature is too low, indoor temperature is less than 10 degrees, it is recommended that the machine be moved to work in the studio with heating supply.

  • Page 56: Chapter 7 Contact Way

    Zone, Quan Jiao County, Chu Zhou City, Anhui Province, China , Zip Code 239500. Tel: 86-550-5185755/655 Fax: 86-550-5185500 Company website: www.han-bond.com Customer service Tel: 400-068-1698 Thank you for your selection of Han-Bond technology H8 ink jet cutting all in one machine.

This manual is also suitable for:

H8-170H8-220H8-190H8 plus

Table of Contents