Advertisement
Quick Links
Instruction Manual
Model:
Function:
Communication:
Input:
Output:
Power:
Serial #:
For Technical Assistance And Questions Call
USA: (231) 788-2900 CANADA: (905) 660-5336
RCI-200-XXX
Remote Control Signal Interface
XXX=SER: RS-232/485
XXX=MDM Modem Dial-Up
XXX=FSK: Leased Line
XXX=RF9: 900 Mhz Wireless
XXX=R
F150 150 MH
:
2 "Dry" Contacts and 2 Analog Inputs
2 Form 'C' Contacts and 2 Analog Outputs
117VAC, 50/60Hz
24 VDC
(If special or required)
Manufacturers of Process
Controls and Instrumentation
z Wireless
Advertisement
Related Manuals for Pribusin RCI-200-RF150
Summary of Contents for Pribusin RCI-200-RF150
- Page 1 Manufacturers of Process Controls and Instrumentation Instruction Manual Model: RCI-200-XXX Function: Remote Control Signal Interface Communication: XXX=SER: RS-232/485 XXX=MDM Modem Dial-Up XXX=FSK: Leased Line XXX=RF9: 900 Mhz Wireless XXX=R F150 150 MH z Wireless Input: 2 “Dry” Contacts and 2 Analog Inputs Output: 2 Form ‘C’...
-
Page 2: Restocking Policy
Restocking Policy All product returned to Pribusin Inc. in prime condition (not damaged, scratched or defaced in any way) within seven (7) months from the original date of shipment is subject to a 50% restocking charge. All product must be accompanied by a Return Authorization number (RA number) which must be obtained from Pribusin Inc. -
Page 3: Standard Features
Model: RCI-200-RF150 Remote Control Signal Interface Manufacturers of Process With 150MHz MURS Radio Frequency Link Controls and Instrumentation Standard Features: Bi-directional Communication using License-free 150MHz Radio Band 2 Watt selectable Radio Power Provides Reliable Communication 150MHz RF Band Does Not Require Line-Of-Sight... - Page 4 RCI-200-RF150 Enclosures & Dimensions: 12.25” 10.25” 6.5” Connection: Remote 1 Remote 2 2 Analog 2 Analog 2 Analog 2 Analog 2 Contact 2 Contact 2 Contact 2 Contact Remote 3 2 Analog 2 Analog 2 Contact 2 Contact 2 Analog...
- Page 7 RCI-200 Connections: The RCI-200 is the main board of an RCI-200-XXX Telemetry system. It provides the input and output signal connections as well as the power supply for the unit. A separate communications board is added to the RCI-200 to allow it to communicate with other units. This communications board may have its own configuration that is in a separate section of this manual.
- Page 8 A maximum of 20mA will flow in such a connection. Make sure to consult the field transmitter manual to determine how to connect it to the RCI-800. ..\Manuals\RCI-200-RF150 rev.B.doc Page 2 of 15...
- Page 9 If both jumpers are IN the analog and contact inputs are passed straight through to the analog and relay outputs. This may help in troubleshooting input and output signals. Make sure both jumpers are removed before resuming normal operation. ..\Manuals\RCI-200-RF150 rev.B.doc Page 3 of 15...
- Page 10 The test points read a voltage of 0-5V for a 0-100% adjustment. Output RampRate Volt Volt where, Output = 0-20 (mA) and Ramp Rate = 0-60 (seconds) (5 sec. minimum) ..\Manuals\RCI-200-RF150 rev.B.doc Page 4 of 15...
- Page 11 1 to 9 using a binary encoding scheme. SW2 assigns the Topology, Channel ID, Channel Numbers and Host/Remote Mode. The switches are located on the left side of the communications board. They are slide type switches that slide up for ON and down for OFF. ..\Manuals\RCI-200-RF150 rev.B.doc Page 5 of 15...
- Page 12 SW2-7. For shorter transmission ranges select the 1W range to limit the amount of ‘RF pollution’. Select the 2W setting if there is no communication at the 1W setting. SW2-7 RF Power 1 Watt 2 Watts ..\Manuals\RCI-200-RF150 rev.B.doc Page 6 of 15...
- Page 13 MURS radio systems. SW1-7 RF Test Mode Disabled Enabled NOTE: While the RF Test Mode is enabled, the RCI will NOT transmit any I/O signals. ..\Manuals\RCI-200-RF150 rev.B.doc Page 7 of 15...
- Page 14 Next, set the number of channels of the host using SW2-3, -4. An RCI-200 can at most have 2 channels. This is the number of channels that will be exchanged between the host and each remote. SW2-3 SW2-4 Channels on Host ..\Manuals\RCI-200-RF150 rev.B.doc Page 8 of 15...
- Page 15 Next, set the number of channels on this remote using SW2-1. One channel is considered 1 analog input/output plus 1 contact input/output. Hence an RCI-200 can have at most 2 channel. SW2-1 SW2-2 Channels on Remotes ..\Manuals\RCI-200-RF150 rev.B.doc Page 9 of 15...
- Page 16 Host Channels: 4 Interval: 10 sec. Remote Channels: 4 Interval: 10 sec. Number of Remotes: 1 MURS Channel: 1 Address: 1 MURS Channel: 1 Channels on Remotes: 4 Power: 1 Watt Power: 1 Watt ..\Manuals\RCI-200-RF150 rev.B.doc Page 10 of 15...
- Page 17 Host Channels: 8 Interval: 10 sec. Remote Channels: 8 Interval: 10 sec. Number of Remotes: 1 MURS Channel: 1 Address: 1 MURS Channel: 1 Channels on Remotes: 8 Power: 1 Watt PHP: 1 Power: 1 Watt ..\Manuals\RCI-200-RF150 rev.B.doc Page 11 of 15...
- Page 18 Remote Channels: 2 Remote Channels: 2 Number of Remotes: 2 Address: 1 Address: 2 Channels on Remotes: 2 MURS Channel: 3 MURS Channel: 3 MURS Channel: 3 Power: 1 Watt Power: 1 Watt Power: 1 Watt ..\Manuals\RCI-200-RF150 rev.B.doc Page 12 of 15...
- Page 19 RCI-200 (Remote 3) Remote Channels: 2 Remote Channels: 2 Remote Channels: 2 Address: 1 Address: 2 Address: 3 MURS Channel: 1 MURS Channel: 1 MURS Channel: 1 Power: 1 Watt Power: 1 Watt Power: 1 Watt ..\Manuals\RCI-200-RF150 rev.B.doc Page 13 of 15...
- Page 20 A higher power setting on the radio or a higher gain antenna can be used to increase signal strength and achieve more reliable operation of the radio system. Signal Strength LED 1 LED 2 LED 3 (dBm) -105 Flashing -100 Flashing Flashing ..\Manuals\RCI-200-RF150 rev.B.doc Page 14 of 15...
- Page 21 Placing them parallel to one another greatly diminishes the transmission between antennas. (YAGI-YAGI) (OMNI-OMNI) (OMNI-YAGI) We suggest you consult Pribusin Inc. or your local Sales Rep. to discuss your antenna and cable requirements. ..\Manuals\RCI-200-RF150 rev.B.doc Page 15 of 15...
Need help?
Do you have a question about the RCI-200-RF150 and is the answer not in the manual?
Questions and answers