Table of Contents
Advertisement
55" LCD TV
Service
Service
Service
Description
Table of Contents........................................................1
Important Safety Notice...............................................2
Revision List........................................................3
1. General Specification..................................................4
2. Operating Instructions.........................................5
2.1 Remote Control..................................................5
2.2 OSD Menus.......................................................8
2.3 Panel Control And Rear Terminal Control............20
3. Input/Output Specification.....................................24
4. Mechanical Instructions........................................28
5. Repair Flow Chart .............................................30
6. PCB Layout .....................................................37
6.1 Main Board .....................................................37
6.2 Power Board .................................................40
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS
AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING
ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING
Table of Contents
Page Description
6.3 IR Board.............................................. ..........43
6.4 KeyBoard..................................................43
6.5 Converter Board ....................................... 44
7. Adjustment..............................................................47
7.1 WB Adjustment..............................................47
7.2 Firmware and DDC Instruction..............................48
8. Block Diagram........................................................49
9. Wiring Diagram.......................................................51
10. Schematic Diagram.........................................52
10.1 Main Board...................................................52
10.2 Power Board.................................................70
10.3 IR Board.......................................................74
10.4 Key Board..................................................75
10.5 Converter Board ....................................... 76
SAFETY NOTICE
1
LE55B7500U
Page
Advertisement
Table of Contents
Related Manuals for Haier LE55B7500U
Summary of Contents for Haier LE55B7500U
-
Page 1: Table Of Contents
55″ LCD TV LE55B7500U Service Service Service Table of Contents Description Page Description Page Table of Contents..……........…..1 6.3 IR Board………….……………..……….…... ……..43 Important Safety Notice........……..2 6.4 KeyBoard……..…………………...…….…..43 Revision List………………………………………………..3 6.5 Converter Board …………...…………………… 44 1. General Specification........………..4 7. Adjustment..............47 2. Operating Instructions..………………….……...……..5 7.1 WB Adjustment..........47... -
Page 2: Important Safety Notice
Important Safety Notice Proper service and repair is important to the safe, reliable operation of all Haier Company Equipment. The service procedures recommended by Haier and described in this service manual are effective methods of performing service operations. Some of these service operations require the use of tools specially designed for the purpose. -
Page 3: Revision List
Revision List Version Release Date Revision Instructions Customer Model Model March-2-2015 Initial release LE55B7500U E55E91NCHDH6NNZ... -
Page 4: General Specification
1. General Specification Model Name LE55B7500U 3840×2160 Resolution 16：9 Aspect Ratio TV System PAL B/G Video Signal System PAL/SECAM/NTSC Receiving Channel 1-255 Input Power Voltage AC 100-240V 50/60Hz Power consumption 160W Audio Output Power（THD≤7%） 2×10W YCb (Pb )Cr (Pr)×1 USB2.0×2 USB3.0×1... -
Page 5: Operating Instructions
2. Operating Instructions 2.1 Remote Control... - Page 6 (POWER) Press to turn the TV on or off. (This key used IR transmission, not RF protocol). 2. SOURCE Press to open Input Source list (reverse) Press to rewind playback in multi-media mode. (play/pause) Press to play/pause playback in multi-media mode 5.
- Page 7 a. Press to navigate OSD menu. b. Press to change setting value in options items. 22. Voice No used Press to adjust the volume level. Press to open (SmartTV) launcher mode. 25. Mute Press to turn the sound on or off. 26.
-
Page 8: Osd Menus
2.2 OSD Menus Video Setup Items Description Picture Mode Select picture mode User, Vivid, Natural, Sports, Lightness, Standard, Soft. Backlight Control the brightness of the backlight. Brightness To brighten the dark parts of the picture. Contrast To sharpen the picture quality. Sharpness To improve details Saturation... - Page 9 Audio Setup Items Description Sound Mode Select sound mode User, Standard, Music, Movie, News. Create vivid and connotation-rich surround sound experience through speakers. Provide ON Digital Surround and OFF setup. Adjust the volume of the left and right speakers. 120Hz, 500Hz, 1.5KHz, 5KHz, 10KHz: Adjust the frequency so that the sound quality is adapted to your favorite.
- Page 10 Items Description TV automatically searches for the channel in the available frequency band and stores sequentially. Select TV menu. Auto Scan Select Auto Scan and press OK key to tune channels automatically and store. During auto searching Press BACK/ key to stop search. Scan the channels manually and store it to the desired channel number.
- Page 11 Manual Scan description 1. Select TV Menu 2. Select Manual Scan and press OK key to get into Sub-Menu 3. Select Search and press key to manual scan previous/next available Channel. 4. Press Back key to exit manual search scan and back to previous menu. Computer Setup This setup function is available in VGA mode.
- Page 12 Smart TV 1. Connect your TV to ethernet. Parts of TV function will not work without network. 2. Press key on remote control to enter smart TV screen. Screen description:...
- Page 13 Android 1. If you need to install the android software, you can download the android applications on the Internet to a USB drive or SD card, and then select from MyFun installation. 2. Choose to place directory software, and select "Install" to start the installation. You can open in AllApps check you have installed the android applications, or open the software.
-
Page 14: Network Setting
Network connection Wired network connection This machine supports network function, be sure to correctly connect the network first. The following are two network connection modes, and you can select the most suitable connection mode according to the actual situation. Connect to a wired routher, so as to connect to the Internet via a wall mounted LAN port. Wireless network connection Connect to the Internet via a wireless router. - Page 15 Ethernet setting If LAN cable is connected and DHCP (automatically set up) is supported, the Internet Protocol (IP) setting will be automatically configured. If you want to manually set up the IP, operate according to the following steps: 1. Press the OK key to select connection so as to automatically obtain an IP address. 2.
-
Page 16: Viewing Photos
3. Select the Media type (All/Picture/Music/Video) to be viewed and press OK key to enter into USB Media and when USBdrive is detected by the TV, USB drive is displayed as a folder on the screen as shown below. 4. Press OK key to view subfolder or files in the USB driver. 5. - Page 17 Multimedia settings for Photo Slide show Press OK key to get following Menu setup shown above. Play/Pause photo play. 2. [Zoom in]: Zoom in the Photo with scale factor (1×/2×/4×/8×). Playing Music files 1. Thumbnail of the available music files will be displayed on the screen. If no files are displayed then select the floder containing the music files.
- Page 18 Multimedia settings for Video play Following Menu setup shown above. (Play/Pause): Play/Pause movie play. (Rewind/Fast Forward): Rewind/Fast Forward video play. (Repeat): Select the repeat mode as Repeat One, Repeat All. (Settings): Enter the settings of Menu. AB (AB Repeat): Press it to enable or disable A-B section period to repeat video content playback. Do not support "Repeat", "Settings"...
- Page 19 10. USB 3.0 port supports USB 3.0 and USB 2.0 devices, but doesn't support USB 1.1 device. USB 2.0 port supports USB 2.0 and USB 1.1 devices, but doesn't support USB3.0 device. * Haier is not responsible for any quality problems or data loss of the external digital storage devices.
-
Page 20: Panel Control And Rear Terminal Control
2.3 Panel Control and Rear Terminal Control Front Panel 1. Remote control sensor. 2. Indicator LED: LED OFF POWER ON STANDBY 3. Key board Back side Power switch 1. Turn on the power switch on the side of the TV. 2. - Page 21 KEYBOARD 1. SOURCE: Display the input source menu. 2. MENU: Display main MENU. 3. VOL+/ VOL- : Adjust sound level. In Menu mode, press "VOL+" or "VOL-" to adjust the item that you selected. 4. CH / CH In TV mode, press CH or CH to change the channel up and down.
- Page 22 Antenna STEPS: Be sure both the TV and computer are Power off. 1. Connect VGA and audio cable. 2. Connect power cord. 3. Power on the TV switch to PC mode. 4. Power on the PC. This sequence is very important. Note: Appearance in the book is a schematic diagram, please buy the real.
- Page 23 AV EQUIPMENT This TV provides two group of AV, one group of YPbPr for convenient connection to VCR, DVD or other video equipment. Please refer to the owner's manual of the equipment to be connected as well. You can use the input terminals on TV set rear as follows. It can be connected to the following appliances: VCR, multi disc player, DVD, camcorder, video game or stereo system, etc...
-
Page 24: Input/Output Specification
3. Input/Output Specification 3.1 Input Signal Connector D-SUB Pin No. Description Pin No. Description +5V (supply from PC) Green Sync GND Blue Bi-directional data (SDA) H-sync Red GND V-sync (vclk) Green GND Data clock (SCL) Blue GND HDMI Pin No. Description Pin No. - Page 25 3.2 Input Signal Timing PC Input Signal Reference Table Connect a computer to your TV set and set up the computer output signal in accordance with table below. Default computer mode Item Resolution Horizontal Frequency (kHz) Vertical Frequency(Hz) 31.469 59.94 640 ×...
- Page 26 DVI/ PC HDMI Input Signal Reference Table When DVI port is being used: connect the DVI port of video device to your TV set with a DVI-to-HDMI line and set up the output signal of the video device in accordance with table below. When HDMI port is being used: connect the HDMI ports of your computer and TV set with one HDMI wire and set up the output signal of the video device in accordance with table below.
- Page 27 Video Input Signal Reference Table Connect the component signal or HDMI port of video device to your TV set and set up the output signal of the video device in accordance with table below. If your computer display card supports signals of video format then you can set up following output signal. Default Component or HDMI Mode Standard Resolution...
-
Page 28: Mechanical Instructions
4. Mechanical Instructions Step1. Remove the BASE. Step2. Remove the REAR COVER. Step3. Remove the Main Board、Power Board、Converter Board 、BKT IO、SPEAKER. - Page 29 Step4. Remove the BKT_STAND. Step5. Remove the Wifi Board 、DECO. Step6. PANEL...
-
Page 30: Repair Flow Chart
5. Repair Flow Chart 1. No power No power (LED “Off”) Check the AC input and Power “On” the power is “ON”? Power board output=5V? Replace the power board Check the IR board and LED Replace the IR board Replace the main board... - Page 31 2. Can’t start Can’t start（LED Blue） Replace the power board Power board output＝12V? Replace the key board Check the power key is under control? Replace the IR board Check the IR receiver is normal? Replace the main board Replace the Power board...
- Page 32 3. Abnormal Display Abnormal Display Reset the source Check the source Enter factory mode to do “EEPROM initial”&“Reset” Replace the main board Check the main board Check the LVDS cable Replace the LVDS cable Check the panel Replace the panel...
- Page 33 4. No display No display (LED Red) Check TV is under control and power Replace the main board on/off by remote control and power key? Check the backlight is “On”? Check the LVDS cable Check the B/L signal is available? Reinsert or replace the LVDS cable Replace main board...
- Page 34 5. Sound problem No sound or sound abnormal Check the audio source connection and the TV system are correct? Reinsert the audio cable or change the TV system Check the TV is muted, adjust the volume or enter the menu to reset? Enter factory mode to do “Reset”...
- Page 35 6. Remote control malfunction Remote Control malfunction Check the remote control battery is Replace the battery not properly placed or no power? Use the other remote controls Replace the remote control Whether the IR board is Replace the IR board abnormal? Replace the main board...
- Page 36 7. OSD is unstable or can’t work normally OSD is unstable or can’t work normally Reconnect the key board Key board connected properly? Replace the button function Buttons are OK? Replace the key board Key board is OK? Enter factory mode to do “Reset” Replace the main board...
-
Page 37: Pcb Layout
6. PCB Layout 6.1 Main Board 715G6591M01002004K... -
Page 40: Power Board
6.2 Power Board 715G6100P06003002H... -
Page 43: Ir Board
6.3 IR Board 715G6721R01002004I 6.4 Key Board 715G6715K01002004I... -
Page 44: Converter Board
6.5 Converter Board 715G6432P01000002H... -
Page 46: Adjustment
7. Adjustment 7.1 WB Adjustment Turn on the TV, then press “Menu+8893”, it will achieve the factory mode. Current Source is "VGA", and then choose Color temp as Warm / Standard / Cool, use remote control to choose “WB Pattern” for 80 .Then choose the Gain bar to adjust the R/G/B value, the temperature adjustment meet to the required specification range. -
Page 47: Firmware And Ddc Instruction
7.2 Firmware and DDC Instruction FW Upgrade Step 1: Ready for F/W Upgrade 1.1 Prepare a FAT 32 format USB memory . 1.2 Copy the software (“HAIER_AP_LE50B7500U_BootUpgrade.bin”and”HAIER_AP_LE50B7500U_Upgrade.bin”) to USB flash disk (root directory). Step 2: F/W Upgrade 2.1 Plug the USB memory on the USB port on the side I/O port of TV. 2.2 AC on (Power plug) 2.3 TV will upgrade automatically, and the LED indicator is flicking during the process. -
Page 48: Block Diagram
8. Block Diagram NAND FLASH DDR3 DDR3 16Mb HDMI A VX1 8 Lanes HDMI C LVDS 4 Links INTERNAL USB 0 INTERNAL USB HUB USB 2 INTERNAL USB 1 INTERNAL USB 2 USB 3 INTERNAL USB 3 USB 3,0 MSD8590QV-YI SD/MMC AMBI-GLOW 1 TUNER... - Page 49 Power Board supper 5V / 12V / 24V Name V Range A (Typ) A (max) +24V +12V_Normal 5_12V 5_12V 4.5~5.5V 600mA (BUCK) (LDO) NC/FB710 NC/FB722 NC/U710 NC/FB718 U704 R708 +12V_Normal 10.8~13.2V 1400mA +5V_STANBY +3,3V_STANDBY TPS54528DDAR AP1117E33L-13-77 (5000mA) (1000mA) +24V 21.6~26.4V 1780mA VDDC 1.15V...
-
Page 50: Wiring Diagram
9. Wiring Diagram LE55B7500U Panel 14 Pin 14 Pin 12 Pin CN701 CN8101 CN9102 4 Pin CN8102 16 Pin CN106 CN9101 51 Pin CN407 Converter Board Main Board Power Board 16 Pin 4 Pin CN601 CN9100 13 Pin CN8101 13 Pin... -
Page 51: Schematic Diagram
10. Schematic Diagram 10.1 Main Board 715G6591M01002004K +5V_Normal => +1.5V_DDR +12V_Normal +12V_SW +5V_Standby +5V_Normal R736 33 OHM 1/16W R719 33 OHM 1/16W BL_ON PS_ON R737 33 OHM 1/16W R764 NC/33 OHM 1/16W 3D_EN_U 9,11 FB701 +1.5V_DDR 300R 4A 5_12V 600 mA. +3.3V_Normal FB705 300R 4A... -
Page 52: Power Interface
U11G Power interface VDDC DVDD_DDR VDDC AVDDL_MOD U11F VDDP_3318 +3.3V_Normal AVDDL_MOD VDDP_3318 (3.3V/1.8V) AVDD3.3V_ST AVDDL_PREDRV AVDDLV_USB AVDDLV_USB AVDD33_LAN DVDD_DDR AVDD_MOD (3.3V) DVDD_RX_1 AVDD_MOD (3.3V) DVDD_RX_2 AVDD_PLL AVDD_AU33 AVDDL_DVI_PC VDDP C441 DVDD_DDR_DECAP AVDD_AU33 AVDD3P3_DMPLL 100N 16V DVDD_RX2_DECAP VDDC VDDC AVDD3P3_DMPLL AVDD3.3V_ST AVDD3P3_MPLL VDDC VDDC... - Page 53 HDMI & LAN & USB & Front End HDMI Interface U11D USB0_D- RX0N DM_P0 USB0_D- 14 USB0_D+ RX0P DP_P0 USB0_D+ 14 USB1_D- RX1N DM_P1 USB1_D- 14 USB1_D+ RX1P DP_P1 USB1_D+ 14 USB2_D- RX2N DM_P2 USB2_D- 14 USB2_D+ RX2P DP_P2 USB2_D+ 14 RXCN RXCP DDCDA_CK...
- Page 54 RGB &CVBS & Audio EMI solution. LINE_IN_0L LINE_IN_0R LINE_IN_2L LINE_IN_2R AM_L AM_R Close to MST IC U11B with wide trace RIN0 RIN0 LINE_IN_0L R401 33 OHM 1/16W C405 47NF 16V C416 2.2U10V VGA-Rin RIN0P LINEIN_L0 HD_Lin 12 R402 33 OHM 1/16W C406 47NF 16V GIN0...
- Page 55 NAND & CI & TS & Front End U11C TS_MDO0 AH11 AG20 PCM_A0 iNAND FLASH TS_MDO0 PCM_A0 19 TS0_D[0] PCM_A[0] AH10 AH20 TS_MDO1 PCM_A1 TS_MDO1 PCM_A1 19 +3.3V_Normal TS0_D[1] PCM_A[1] TS_MDO2 AF12 AF20 PCM_A2 TS_MDO2 PCM_A2 19 TS0_D[2] PCM_A[2] TS_MDO3 AG11 AH19 PCM_A3...
- Page 56 U11A Connector +3.3V_Standby +5V_Standby +3.3V_Standby +3.3V_Normal PANEL_ON/OFF GPIO_PM0 11,20 PANEL_ON/OFF GPIO_PM[0] / (PANEL_ON/OFF) U_A0P TO IR/KEY BOARD AM_RESET GPIO_PM[1] / (PM_UART_TX) U_A0M MHL_CABLE_DET R440 MHL_CABLE_DET GPIO_PM[2] / (MHL_CDS) U_A1P MHL_VBUS_EN NC/1.5K +-1% 1/10W MHL_VBUS_EN GPIO_PM[3] / (MHL_VBUS_EN) U_A1M PWR-ON/OFF CN401 4,14,20 PWR-ON/OFF GPIO_PM[4] / (PWR_ON/OFF)
- Page 57 DDR3 4Gb 1866MHz +1.5V_DDR +1.5V_DDR Hynix H5TQ4G63AFR-RDC 356G0615004601 +1.5V_DDR Samsung K4B4G1646B-HCMA Nanya NT5CB256M16CP-EK MRP11 MRP21 A-DDR3-A0 A_DDR3_RASZ A-DDR3-RASZ B_DDR3_RASZ B-DDR3-RASZ A-DDR3-A1 A_DDR3_ODT A-DDR3-ODT B_DDR3_ODT B-DDR3-ODT A-DDR3-A2 U11E A-DDR3-A3 A-MVREFDQ VREF_DQ A_DDR3_A0 B_DDR3_A0 A-DDR3-A4 A-MVREFCA MRP13 MRP22 A_DDR3_A[0] B_DDR3_A[0] VREF_CA A_DDR3_A1 B_DDR3_A1 A_DDR3_CASZ A-DDR3-CASZ...
- Page 58 VbyOne TX 8 Lanes CN407 LVDS TX 4 Links CONN for INX 50 4K2K@60Hz for FHD@120Hz +PANEL_POWER Vertical 311GW200C30AAL / 311GW200C40AAL (TOP Right angle ) (TOP Vertical angle ) Right Angle 311GW200C40ABL CN413 NC/CONN +PANEL_POWER LVDS TX 2 Links INX NC for FHD@60Hz (TOP Vertical angle ) ACKP...
- Page 59 YPbPr & AV Input(Down) SPDIF OUT(Side) Side AV Input NC/RCA JACK Close to Mstar IC CO-layout with spdif PC & YPbPr & AV Audio-Input CN107 R137 SPDIF SPDIF_O CN103 NC/0R05 OHM RCA JACK R101 C7114 SCART-AV-IN 7 0R05 OHM C106 R109 NC/10PF 50V 75R 1/16W 1%...
- Page 60 +5V_Standby VGA Input (Down) R116 10K 1% R117 10K 1% CN105 VGA_5V VGA-Rin VGA-Rin 7 VGA_SDA PC_SDA VGA-Gin R144 R118 100R 1/16W 1% UART-TX VGA-Gin 7 0R05 OHM VGA_HSY NC PC_HSY NC VGA-Bin R119 100R 1/16W 1% VGA_HSY NC VGA-Bin 7 VGA_VSY NC PC_VSY NC R120...
- Page 61 +3.3V_Normal +5VUSB INTERNAL USB 0 INTERNAL USB 1 U101 NC/USB2514B-AEZC close cn106 FB114 NC/120R Upstream +5VUSB +3.3V_Normal CN106 FB116 NC/120R R199 NC/5.1R 1/16W USB0_D- 6 USBUP_DM FB113 120R CONN CN114 R157 NC/100K 1% VBUS_DET +5VUSB FB115 NC/120R NC/CONN R200 NC/5.1R 1/16W USB0_D+ 6 USBUP_DP R127 5.1R 1/16W...
- Page 62 trace : diffenentail 100 R CN112 U507 RJ45 15P TCT P1 MDI_TP MDI_TP TD+ P2 MDI_TN MDI_TN TD- P3 RD+ P4 MDI_RP MDI_RP RD- P5 MDI_RN MDI_RN RCT P6 NC P7 NC P8 FB105 NC P9 NC/120R NC P10 +5V_Normal NC P11 Y - P12 FB103...
- Page 63 HDMI? (Down) / ARC +HDMI2/5V HDMI ARC Function CN503 +HDMI2/5V R520 U504 10K 1% SHLD0 HDMI2_RX2P HDMI2_CLKN R551 0R05 OHM HDMI2-CLKN 6 TMDSD2+ HDMI2_CLKP R553 0R05 OHM HDMI2-CLKP 6 SHLD2 DSHLD0 HDMI2_RX2N HDMI_ARC C502 R523 HDMI-ARC HDMI-ARC 6 TMDSD2- HDMI2_RX1P HDMI2_RX0N R554 0R05 OHM...
- Page 64 ST29WN-20I-E TU101 +3.3V_Tuner +5V_Normal I2C address +1.2V_DM FB1404 260mA (typ) U707 +3.3V_Tuner Write U708 AP1117E33L-13-77 R733 11000000=0XC0 VOUT VOUT 120R 3A C746 SCL-T SDA-T C192 R213 +3.3V_Tuner ADCINN_DEMOD 6 R215 100R 1/16W 1% NC/0R05 1/16W IF-IN+ C208 VIFM VIFM C191 43mA(max) IF _P 100N 16V...
- Page 65 +AMP_12V D6003 2.0 CH +AMP_12V AD82588 FB6011 L601 R652 0R05 C607 HCB3216KF-121T30 22uH C602 AD83586 R653 0R05 2.1 CH 10UF 50V C603 100N 50V AD83586 470PF 50V C610 C611 C612 C613 C614 C615 C604 R605 10K 1/4W 10N 50V 100N 50V 100N 50V 100N 50V 100N 50V...
- Page 66 SD/MMC Card Reader PCMCIA +3.3V_Normal CN115 NC/SD Card Push Ty pe(II) HNC21 VCC-PCMCIA SD-D3 CD/DAT3 VCC-PCMCIA SD-CMD CN113 VSS1 PCM_CD1_N PCM_D3 PCM_D3 8 CD1# TS_MDO3 PCM_D4 SD-CLK PCM_D4 8 TS_MDO4 PCM_D5 PCM_D5 8 VSS2 TS_MDO5 PCM_D6 VCC-PCMCIA SD-D0 PCM_D6 8 DAT0 TS_MDO6 PCM_D7...
- Page 67 C1802 C1805 +1.8V_Normal DVDD3V3 Q1803 3.8A @ 70 C C1808 +12V_SW +1.8V_Normal FB1801 LED_PWR Q1801 LED_PWR F701 DVSS AVDD R1823 DVSS AVDD C1806 AM_RESET RESET GND_Sense U1802 GPIO/MFP5 R1822 R1829 7,9,18 I2S_MCLK MCLK 4.6A @ 70 C BCLK IN3_R WCLK IN3_L C1801 DVDD3V3...
- Page 68 DVDD3V3 FB1815 DVDD3V3 LED_PWR LED_PWR LED_PWR C1830 R1830 C1828 C1829 M_SDA 9,11,17,18,20 R1826 M_SCL 9,11,17,18,20 CN1803 U1803 AMBI_B0 CN1804 AMBI_B1 AMBI_B2 AMBI_B3 AMBI_B6 TL_G TR_G AMBI_B4 AMBI_B5 TL_R TR_R LED0 FB1809 TL_R LED1 LED7 TL_B TR_B LED2 LED6 TL_G FB1810 LED3 LED5 LED4...
-
Page 69: Power Board
10.2 Power Board 715G6100P06003002H CN9903 CONN F9901 FB9901 FUSE BEAD RV9902 C9903 C9907 TS10K80-02 47pF 250V 220PF 250V BD9902 L9902 L9903 L9901 0.25mH RV9901 C9905 C9906 620V 470NF 275V 470NF 275V CN9902 14mH SOCKET C9904 14mH 47pF 250V C9902 220PF 250V NR9901 NR9902 Vsin... - Page 70 +24Va Max:4.5A D9103 T9101 FB9102 L9103 FCHS30A08 BEAD 1.1uH +24VLED R9113 R9114 R9115 FB9103 1M 1% 1/4W 1M 1% 1/4W 1M 1% 1/4W BEAD C9131 C9134 C9129 C9132 C9133 C9114 C9135 R9123 R9124 C9116 R9141 C9138 R9116 330UF 35V 330UF 35V 330UF 35V 330UF 35V 330UF 35V...
- Page 71 BD9801 KBP306G-05 C9817 100PF1KV L9801 300uH Vsin FB9801 D9802 FB9802 BEAD FMNS-1106S BEAD C9801 C9811 C9812 C9814 470PF 1UF 450V 56uF 500V 56uF 500V C9802 10NF R9805 20K 1/4W VCC1 IC9801 R9804 LD7591T 1M 1% 1/4W R9802 33R 1/8W 5% 10 OHM 1/8W R9803 COMP...
- Page 72 BEAD R9302 R9301 FB9301 T9301 47 OHM 1/4W 0.1R POWER X'FMR C9303 R9305 2.2NF 47 OHM 1/4W R9303 R9304 100K 1/4W 100K 1/4W Max:2A C9311 C9312 10NF D9302 FMW-2156 L9302 R9306 R9307 100K 1/4W 100K 1/4W R9308 4R7 1/4W 5% C9304 D9304 C9315...
-
Page 73: Ir Board
10.3 IR Board 715G6721R01002004I LED201 LED_R CN201 U201 Vout R201 15K 1/16W 5% TSOP75438TR CONN C201 2.2uF 10V T P V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL Size TPV MODEL 絬 隔 瓜絪 腹 02-IR&LED Key Component PCB NAME <... -
Page 74: Key Board
10.4 Key Board 715G6715K01002004I SW01 MENU 2.411V 27K 1/10W 1% TACT SW FWRD H1.5MM SW02 INPUT 1.985V 15K 1/10W 1% TACT SW FWRD H1.5MM SW03 VOL+ 1.497V 8K2 1/10W 1% TACT SW FWRD H1.5MM SW04 VOL- 1.070V 4K7 1/10W 1% TACT SW FWRD H1.5MM SW05 0.660V... -
Page 75: Converter Board
10.5 Converter Board 715G6432P01000002H ON/OFF 2D/3D CN8101 CN8102 D8101 VLED+ CONN L8101 VLED+ 300uH +12V +36V VLED_1- MBRF10150CT R8111 C8105 C8106 C8107 C8108 C8101 C8102 330UF 50V C8112 330UF 50V 100N 50V R8138 R8139 R8140 VLED_2- 100UF 160V 100UF 160V L8102 Q8101 C8116...