Introduction ........................4 2.2. SYSTEM COMPONENTS ....................5 Features ............................ 6 3.1. 2LINE-6..........................6 3.2. 2LINE-Sub ......................... 6 Applications ..........................7 4.1. Portable Stereo System ...................... 7 4.2. Single microphone with 2LINE System ................8 4.3. 2LINE System for Installation....................9 Set-up and Use of the 2LINE Sub ....................
3. This manual must be read and understood and ALL warnings must be followed. 4. Follow all instructions to insure optimal product performance. 5. The 2LINE-Sub is a convection-cooled device and requires at least 6 inches (152 mm) of clearance behind the enclosure to allow the heat sink to adequately cool the internal electronics.
2LINE-Sub powered cabinet, which features a solid wooden cabinet with 300w of amplification available for the 10” woofer. The amplifier also has a powered output, allowing the 2LINE-Sub to also power the 2LINE-6 column array with 300w of amplification. Together, the 2LINE system boasts 600w of power in a tiny package.
The 2LINE-6 also features switchable impedance for use in distributed systems. Standard column impedance is 4 ohms, for use with the 2LINE-Sub, but once the 16 ohm impedance is selected, up to 4 cabinets can be linked to either the 2LINE-Sub output channel or another 4 ohm stable amplifier.
Switchable 4 ohm or 16 ohm operation Multiple rigging accessories High power handling transducer elements 3.2. 2LINE-SUB 10” Actively Driven Subwoofer Enclosure Speaker Level Output for easy system set up Optimised for use with the 2LINE-6 Column Loudspeaker ...
4. APPLICATIONS 4.1. PORTABLE STEREO SYSTEM The combined 2LINE system is an ideal system for quick, easy set up at small events. The on board amplification ensures system cabling is kept to a minimum for discreet sound reinforcement at corporate events, wedding receptions and other events.
4.2. SINGLE MICROPHONE WITH 2LINE SYSTEM The XLR input on the 2LINE sub can be switched between microphone and line level sensitivity. The on board EQ pre-sets ensures that clear vocals can be achieved when set to the ‘Vocal’ pre-set. CHECK!
Up to 4 x 2LINE-6 cabinets may be linked when configured for 16 ohm nominal impedance. This is ideal for distributed fixed installation requirements when combined with the rigging accessories in the 2LINE system. For optimal sound balance it is recommended that 2 2LINE-6 cabinets are linked from each 2LINE-Sub whilst in 16 ohm configuration.
Prior to connecting the AC mains cable, ensure that the AC mains switch is in the OFF position. The 2LINE-Sub uses a standard IEC-type AC mains connector system. To mate the AC mains cable with the AC mains connector on the amplifier, simply align the plug with the panel’s connector and press the AC mains cable into place.
(or other source output) are reduced or muted prior to applying power. 5.2. AUDIO CONNECTIONS The image below illustrates the 2LINE-Sub input plate. The audio input and link output connectors are shown, along with the input sensitivity selector, pre-set selection knob and ground lift switch.
2LINE-Sub and the mid hi cabinet. The output from the 2LINE-Sub is on pins 1+/1- of the speakon connector. To insert the cable into the 2LINE-Sub, insert the connector until fully into the socket, then turn the connector clockwise until it clicks into position.
After all audio and power connections have been made, the gain control is at minimum, and all cables have been double checked, it is safe turn on the 2LINE-Sub. Press the switch from the ‘off’ to the ‘on’ position. Due to the soft start mechanism in the 2LINE-Sub amplifier, do not be alarmed if the audio takes a few seconds to radiate.
3. If AC Mains voltage is present, verify that the fuse is not blown. 4. Replace fuse with same type! 5. If the problem has not been fixed, please contact your local P.Audio distributor for service information. NOTE: IF THE FUSE IS BLOWN REPLACE ONLY WITH THE SAME TYPE OF FUSE.
Care should be exercised when disconnecting the amplifier module from both the woofer. Be sure to observe the wiring polarity of the woofer. 7.1. REPLACEMENT COMPONENTS Description Code 10” Speaker 2LINE F01011005611PAA 2LINE Amplifier Module R6001002701...
8.2. 2LINE-6 Specifications: Frequency Response 200Hz – 20kHz on axis Power Handling 150 watts continuous (600 peak) Sensitivity 94dB 1 watt at 1 meter Impedance (nominal) 4 ohms or 16 ohms (user switchable) Coverage 120 degrees horizontal 10 degrees min vertical Dimensions 380 x 62 x 102.9mm 15 x 2.4 x 4 inches...