Digital Tuner - Philips AZ3300 Owner's Manual

DIGITAL TUNER

DIGITAL TUNER
Tuning to radio stations
1. Press POWER to on, then press CD•FM•MW•LW
(or TUNER on remote control) to select TUNER.
™ TU is displayed briefly and then the radio
station frequency, waveband and, if
programmed, a preset number are shown (See 3)
2. Press CD•FM•MW•LW ( or BAND on remote con-
trol) once or more to select your waveband.
3. Press and hold SEARCH ∞ or § until the
frequency in the display starts running.
™ The radio automatically tunes to a station of
sufficient reception. Display shows Srch
during automatic tuning.
4. Repeat step 2 if necessary until you find the
desired station.
• To tune to a weak station, press ∞ or § briefly
and repeatedly until you have found optimal
reception.
To improve radio reception:
• For FM, extend, incline and turn the telescopic
antenna. Reduce its length if the signal is too
strong.
• For MW or LW , the set uses a built-in aerial.
Direct this aerial by turning the whole set.
Programming radio stations
You can store up to a total of 30 radio stations
(20 FM, 5 MW and 5 LW) in the memory, manually or
automatically (Autostore).
DIGITAL TUNER
Manual programming
1. Tune to your desired station (see Tuning to radio
stations).
2. Press PROGRAM to activate programming.
™ PROGRAM flashes.
3. Press TUNER PRESET 4 ,3 once or more to select
a preset number.
• Remote control : Press PRESET 3, 4 once or
more to select a preset station.
4. Press PROGRAM to confirm.
5. Repeat steps 1-4 to store other stations.
Note : You can erase a preset station by storing
another frequency in its place.
Autostore
Autostore automatically starts programming radio
stations from preset 1. Available stations are
programmed in order if the station with sufficient
reception strength. Any previous presets e.g. manually
programmed will be erased.
• Press PROGRAM for 2 seconds or more to activa-
te autostore programming.
™ The display shows AUtO, PROGRAM blinks,
followed by the radio station details when
stored.
After all stations are stored, the first preset station
will then automatically play.
To listen to a preset station
• Press the TUNER PRESET 4 ,3 buttons once or
more until the desired preset station is displayed.
• Remote control : optionally, press PRESET 3, 4 to
select your preset station.
CD PLAYER
Playing a CD
This CD player plays Audio Discs including CD-
Recordables and CD-Rewritables.
1. Adjust the CD•FM•MW•LW to CD (or CD on
remote control)
2. Open the CD Door.
™ OPEN is displayed.
3. Insert a CD with the printed side facing up and
close the door.
™ no cd if no CD inserted/ CD dirty, incorrectly
inserted or damaged.
™ nF cd if you have inserted a non-finalized CD-
R(W).
4. Press 2; to start playback.
™ dAtA if your CD contains non-audio i.e. data
files.
5. To pause playback press 2;. Press 2; again to
resume play.
™ Display: B flashes during pause.
6. To stop CD playback, press the 9 button.
Note : CD play will also stop when:
- the CD door is opened
- the CD has reached the end
- you select FM / MW / LW function.
Selecting a different track
• Press SEARCH ∞ or § once or repeatedly to
select your track.
• In the pause / stop position, press.2; to start
playback.
CD PLAYER
Finding a passage within a track
1. Press and hold SEARCH ∞ or §.
– The CD is played at high speed and low volume.
2. When you recognize the passage you want,
release ∞ or § to resume normal playback.
Different play modes: SHUFFLE and REPEAT
You can select and change the various play modes
before or during playback, and combine the modes
with PROGRAM. (See 4)
SHUFFLE - tracks of the entire CD/ program
are played in random order
SHUFFLE REPEAT ALL - to repeat the
entire CD/ program continuously in random order
REPEAT ALL - repeats the entire CD/
program
REPEAT - plays the current track continuously
1. To select play mode, press MODE once or more.
2. Press 2; to start playback if in the stop position.
3. To select normal playback, press MODE
repeatedly until the various modes are no longer
displayed.
– You can also press the 9 button to cancel your
play mode.