Bosch WTW83260GB Instruction Manual page 2

Only when switched off!
Care and cleaning Installation
Heat exchanger
– Scope of delivery: dryer, operating and installation instructions, basket for woollens
The dryer's heat exchanger is cleaned automatically during drying. SELF CLEANING appears (depending on the model).
rolling in the display panel. Do not pull out the condensate container during the cleaning – Check the dryer for transport damage.
process.
– The dryer is very heavy. Do not attempt to lift it on your own.
Dryer housing, control panel
– Be careful to avoid sharp edges.
– Wipe with a soft, damp cloth. – Do not lift the dryer by protruding parts (e.g. the door) - risk of breakage.
– Do not set up in a room that is susceptible to frost.
– Do not clean with a water jet.
Freezing water may cause damage.
– Remove detergent and cleaning agent residue immediately.
– If in doubt, have the appliance connected by a specialist.
– Some water may collect between the window and the seal during drying.
This does not affect the proper operation of your dryer in any way.
1. Setting up the dryer
Filter in the condensate container – The mains plug must always be accessible.
– Ensure that the appliance is placed on a clean, level
The filter is cleaned automatically when the condensate container is emptied.
and firm surface.
However, the filter should still be cleaned regularly under running water This prevents
– Do not obstruct the air inlet on the dryer.
stubborn deposits/dirt from building up.
– Keep the area around the dryer clean.
1. Pull out the condensate container.
– Level the dryer using the threaded feet
and a spirit level.
Never remove the threaded feet!
Do not install the dryer behind a door
or sliding door which could prevent or
2. Pull the filter out of its snap-in lock. obstruct the dryer door from opening.
This will prevent children from locking
themselves in and risking their lives.
3. Clean the filter under running water or in the dishwasher.
2. For mains connection,
– Connect to an AC earthed socket. If in doubt have the socket checked by a specialist.
– The mains voltage and the voltage shown on the rating plate (
same.
– The connected load and necessary fuse protection are specified on the rating plate.
Frost protection
4. Refit the filter.
5. Insert the condensate container so that it locks into place.
Preparation
1. Empty the condensate container
Only operate the dryer with the filter inserted.
2. Select any programme using the programme selector.
3. Press the Start/Reload button
4. Wait several minutes or until the dryer stops, and then empty the condensate container
Moisture sensors again.
5 Turn the programme selector to Off.
The dryer is equipped with stainless steel moisture sensors.
Moisture sensors measure the moisture level of the laundry.
Transport
After sustained, repeated operation, a fine layer of limescale
may form on the moisture sensors.
– Prepare the dryer see Frost protection.
1. Open the door.
– Transport the dryer in a vertical upright position.
2. Clean the moisture sensors with a damp sponge which has a rough
– Following transportation, do not use the dryer for two hours.
surface.
The dryer contains residual water;
Do not use steel wool or abrasive agents!
this can flow out if the dryer is tilted.
8
Technical Data
Dimensions (DxWxH) 60 x 60 x 85 cm (height adjustable)
Weight approx. 51 kg
Max. capacity 8 kg
Condensate container 4.0 l
Connection voltage 220-240 V
Connected load 1000 W
Fuse protection 10 A
Ambient temperature 5 - 35°C
Product number Production number Inside of door
Take all accessory parts out
of the drum. The rating plate can be found on the back of the dryer.
The drum must be empty.
Power consumption when switched off 0.10 W
Power consumption when ready for use (left-on mode) 1.00 W
Drum interior light (depending on model): The drum lights up after the door is opened
and after the programme starts, and switches off automatically.
Consumption values table
Spin speed which
Programme is used for spinning Duration**
the laundry
Cottons 8 kg 4 kg
Cupboard Dry* 1400 rpm 179 min 111 min
1000 rpm 203 min 122 min
800 rpm 227 min 143 min
Iron Dry* 1400 rpm 125 min 75 min
Clean and level
1000 rpm 150 min 90 min
Make sure that the air inlet
800 rpm 176 min 106 min
remains unobstructed
Easy-Care 3.5 kg
see Safety instructions page 13. Cupboard Dry* 800 rpm 55 min
600 rpm 71 min
page 10) must be the * Programme setting for testing in accordance with the applicable EN61121 standard.
** The values may differ from those specified, depending on the type of fabric, composition of laundry to be dried, residual moisture in the fabric,
the degree of dryness that has been set, the amount of laundry being loaded and the environmental conditions.
Most efficient programme for cotton fabrics
Do not operate the dryer if
there is a risk of frost.
The following "standard cottons programme" (identified with ) is suitable for drying normal, wet cotton laundry and is most efficient in terms of
its combined energy consumption for drying wet cotton laundry.
page 4,8/12. Standard programme for cottons in accordance with current EU regulation 932/2012
Energy
condensation is pumped into the container. Programme Load
consumption
Cottons Cupboard Dry
8 kg/4 kg 1.80 kWh/1.04 kWh
Programme setting for testing and energy labelling in accordance with Directive 2010/30/EU.
Optional accessories
(order from the after-sales service using the order number, depending on the model)
WTZ Washer-dryer stack connection set
The dryer can be placed on top of a suitable washing machine with the same width and depth to save space.
20410
The dryer must be fastened to the washing machine using this connection set.
WTZ 11400: with pull-out worktop.
Platform
WMZ
For easier loading and unloading. The basket contained in the drawer can be used to carry the laundry.
20500
Wollens basket
WMZ
For drying individual wollen fabrics, sports shoes and soft toys (see separate instructions for "Woollens
9 20600
basket").
Normal noises What to do if ...
During drying, the compressor and the pump generate some noise which is entirely normal.
The compressor in the dryer may
occasionally generate a humming noise.
The volume and pitch of this may vary
depending on the selected
programmes and the progress of the
drying.
Energy consumption**
The compressor in the dryer is ventilated
from time to time, which creates a whirring
8 kg 4 kg
sound.
1.57kWh 0.93 kWh
1.80 kWh 1.04 kWh
2.04 kWh 1.25 kWh
1.10 kWh 0.66 kWh
1.36 kWh 0.82 kWh
1.64 kWh 0.98 kWh
3.5 kg
0.51 kWh
0.66 kWh
The automatic cleaning process causes
a clicking noise.
Programme duration
203 min/122 min
The process of pumping the condensation
into the condensate container generates
pumping noises.
11
10
After-sales service
Turn the programme selector to Off and remove
the mains plug from the socket.
If you cannot rectify the fault yourself (e.g. switching off/on)
The Start/Reload indicator light does not light up. Mains plug plugged in? We will always find an appropriate solution and avoid unnecessary visits by engineers.
Programme selected?
The contact details of your local after-sales service can be found in the enclosed after-sales service directory.
Check the socket fuse.
Please provide the after-sales service the product number (E no.) and the production number (FD) of the appliance.
The display panel light and indicator lights (depending Energy-saving mode is activated see the separate Energy-saving mode instructions.
– GB 03 448 928 979 (Calls charged at local or mobile rate.)
on model) go out and the
– IE 01450 2655 (0.03 € per minute at peak. Off peak 0.0088 € per minute.)
Start/Reload indicator light flashes.
The display panel switches off. The appliance goes into the sleep mode after activating Finished in option page 5.
The (Condensate container) indicator light Empty the condensate container page 4.
Product number Production number
flashes. Press the Start/Reload button to reset the displayed indication and then press the Start/
Reload button again to restart the appliance if necessary.
Trust the expertise of the manufacturer. Contact us for assistance. In this way, you can rest assured that the repair will be carried
(Fluff filter) indicator light flashes. Clean the fluff filter page 4/8.
out by trained service technicians using original spare parts.
Press the Start/Reload button to reset the displayed indication and then press the Start/
Reload button again to restart the appliance if necessary.
Safety instructions
SELF CLEANING appears in the display panel. Not an error. Automatic cleaning of the heat exchanger.
Do not empty the condensate container.
Dryer does not start. Start/Reload button selected? Emergency – Pull the appliance plug out of the socket immediately or disconnect the fuse.
Door closed?
ONLY use the – in rooms inside the house.
Ambient temperature greater than 5°C? The optimum ambient temperature for drying is dryer... – to dry fabrics.
between 5 °C and 35 °C.
The dryer must – be used for purposes other than those described above.
Programme terminates shortly after starting. Is the appliance loaded with the laundry? NEVER... – be modified in terms of its technology or properties.
Load too small for selected programme?/Use timed programme page 6/7.
Hazards – The dryer must not be used by children or persons who have not been instructed in its use.
Loaded laundry dry?
– Do not leave children unsupervised near the dryer.
Water is leaking out. Make sure the dryer is level. – Keep pets away from the dryer.
– Remove all objects from pockets, and lighters in particular
– Do not lean or sit on the door
The door opens by itself. Push the door closed until you hear it engage.
Installation – Secure loose cables Risk of tripping.
– Do not operate a dryer if there is a risk of frost.
Creasing. Laundry load exceeded?
Remove articles of clothing immediately after the end of the programme, hang up and pull Mains connection – Connect the dryer to an AC earthed socket according to specifications, otherwise it cannot be guaranteed that the
into shape. appliance is completely safe.
Unsuitable programme selected page 7. – The cable cross-section must be sufficient.
Laundry is not dried correctly or is still too damp. After the end of the programme, warm laundry feels damper than it actually is. Spread the – Only use earth-leakage circuit breakers with the following symbol:
laundry out and allow the heat to disperse. – The appliance plug and socket must be compatible.
– Do not use multiple plugs/connectors and/or extension cables.
Finely adjust the dryness level – this extends the drying time but does not increase the
– Do not touch or hold the appliance plug with wet hands
temperature. Your laundry will become drier.
– Never pull the appliance plug out of the socket by its cable.
Select a programme with a longer drying time or increase the drying level. This does not – Do not damage the mains lead
increase the temperature. Operation – Only load the drum with laundry. Check the contents before you switch the dryer on.
– Do not use the dryer if the laundry has been in contact with solvents, oil, wax, grease or paint (e.g. hair styling products,
Select a time programme for extended drying of laundry that is still damp.
nail varnish remover, stain remover, cleaning solvent, etc.)
– The tumble dryer is not to be used if industrial chemicals have been used for cleaning.
If you have exceeded the maximum load for the programme, the laundry may not be dried
correctly. – Dust (e.g. coal dust, flour) poses a danger: Do not use the dryer
– Do not turn off the dryer until the drying process ends, unless the laundry will be removed quickly and spread out, so
Clean the moisture sensor in the drum. A fine layer of limescale may adversely affect the that the heat can dissipate.
performance of the sensors and your washing will not dry properly.
– Do not put laundry containing foamed material/rubber in the dryer
be damaged due to possible deformation of the foamed material.
Drying has been interrupted as a result of a power cut, because the condensate container
– When cleaning the fluff filter, make sure that no foreign material (down or filling material) gets into the air duct opening.
is full or because the maximum drying time has been exceeded.
If necessary, clean the drum beforehand with a vacuum cleaner. If foreign material should still get into the air duct
Drying time too long. Clean the fluff filters under running water page 4/8. call the after-sales service
– Light things, such as long hair, may be sucked into the air inlet of the dryer
Insufficient supply of air Ensure that air can circulate.
– Final part of a tumble dryer cycle occurs without heat (cool down cycle), to ensure that the items are left at a
temperature that ensures that the items will not be damaged.
Air inlet possibly blocked Clear inlet page 9.
– Switch off the dryer once the programme has ended.
Ambient temperature higher than 35°C Ventilate the room. The optimum ambient – The water from condensation is not drinking water and may be contaminated with fluff.
temperature for drying is between 5 °C and 35 °C. Outside of this range, the drying time
Defect – Do not use the dryer if it is defective or if you suspect that it is.
may increase.
Repairs must only be carried out by the after-sales service.
One or more indicator lights are flashing. Clean the fluff filter page 4,8/12. – Do not use the dryer if the mains cable is defective. To avoid danger, only have the defective mains cable replaced by
the after-sales service.
Check the installation conditions page 9.
Switch off, allow to cool, switch back on and restart the programme.
Spare parts – For safety reasons, you must only use genuine spare parts and accessories.
Power failure. Remove the laundry from the dryer immediately and spread out. This allows the heat to Disposal – Pull out the appliance plug, then cut off the mains cable from the appliance.
dissipate. Be careful as the door, the drum and the laundry may be hot.
Dispose of the appliance at a municipal waste disposal facility.
– Heat exchangers contain a fluorinated greenhouse gas (R134a) in hermetically sealed equipment
Other intermittent noises and vibrations. Not an error.
Normal noises page 11. a proper manner. Capacity: 0.220 kg. Total GWP: 0.315 tCO
– Packaging: Keep all packaging out of reach of babies and children
Loud humming noise for several seconds. Has the condensate container been properly inserted?
– All materials are environmentally sound and can be reused.
Push the condensate container all the way in. 12 Dispose of them in an environmentally-responsible manner.
Not an error. Normal noises page 11.
What to do if..., page 12, please contact our after-sales service.
You can find this information: inside the door* / in the opened
service flap* and on the rear of the appliance.
*depending on the model
Risk of explosion.
Risk of tipping.
Risk of electric shock.
Risk of electric shock.
Risk of fire/explosion.
Risk of explosion.
elastic material may be destroyed and the dryer
Dryer
WTW83260GB
Risk of fire/explosion.
Risk of injury.
en Instruction manual
dispose of in
.
2
Risk of suffocation.
13