Monacor VIEWEX-640 Instructions page 2

VIEWEX-640
Order number 18.7610
VIEWEX-650
Order number 18.7620
VIEWEX-670WDR
Order number 18.7630
ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS
GB Surveillance Camera
These operating instructions are intended for the
installer of the camera. Please read the operating
instructions carefully prior to installation and keep
them for later reference.
1 Applications
This colour camera is especially designed for video sur-
veillance systems (CCTV). It is equipped with a lens with
variable focal length and features automatic day/ night
switching. Due to its weatherproof housing (IP 66), the
camera is also suited for outdoor applications. During
darkness, the infrared LEDs illuminate the surveillance
area.
2 Safety Notes
The camera corresponds to all relevant directives of the
EU and is therefore marked with .
G
The camera housing is weatherproof, but not ab-
solutely watertight. Therefore, do not immerge the cam-
era into water.
G
Protect the camera against extreme temperatures (ad-
missible ambient temperature range: -10 °C to +50 °C).
G
Never touch the lens with your fingers. For cleaning the
lens, only use optical lens cleaners.
G
For cleaning the housing, never use aggressive deter-
gents or chemicals.
G
No guarantee claims for the camera and no liability for
any resulting personal damage or material damage will
be accepted if the camera is used for other purposes
than originally intended, if it is not correctly installed or
if it is not repaired in an expert way.
If the camera is to be put out of operation defin-
itively, take it to a local recycling plant for a dis-
posal which is not harmful to the environment.
®
MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany
VIEWEX-850
VIEWEX-870WDR
3 Installation
1) To find the optimum place of mounting, make a test run.
2) At the location of mounting, drill four holes for fixing the
base (4) and, if necessary, drill a hole for the connec-
tion cable (the cable can also be guided through the
cable inlet at the side of the base). Fasten the base at
the place of mounting with screws. If necessary,
loosen the setscrews (3) of the base and the camera
support, using the hex key supplied.
3) Connect the BNC inline jack (10) via a 75 Ω coaxial
cable to the video input of a monitor. Observe the cor-
rect 75 Ω termination on the monitor or, in case of
series connection, on the last monitor. For a cable
length of more than 100 m, a video amplifier should be
inserted between camera and cable to compensate
level loss.
4) Connect a regulated 12 V power supply with a suffi-
cient permanent current rating ( chapter 5) to the
inline jack (9). A low-voltage plug 5.5 / 2.1 mm (exterior/
interior diameter) is re quired. Make absolutely sure to
observe the correct polarity (centre contact = +).
CAUTION The infrared LEDs switch on in case of
darkness. When setting up the camera, never look
directly into the lit infrared LEDs from a close range.
The infrared light may cause eye irritation. However,
the infrared radiation is far below the emission limit
and rated risk-free according to EN 62471.
5) Please observe the following for outdoor installations:
The connections (9 – 10) and the cable splitter (5) are
not weatherproof and must be protected accordingly.
6) Switch on the monitor connected and align the camera
by means of the monitor image: Loosen the setscrews
(3), using the hex key supplied, and position the cam-
era as desired. Then tighten the screws again. Protect
the lens against direct sunlight; otherwise the CCD
chip may be damaged. To move the sunshield (1),
loosen the setscrew (2).
Use the zoom screw (7) to adjust the angle of view
and the focus screw (8) to focus the image on the
monitor.
4 Adjustments via the On-screen Menu
Camera models featuring an on-screen menu are
equipped with a control lever (6) at the cable splitter. To
display the on-screen menu, press the control lever. The
main menu or will appear:
Order number 18.7650
Order number 18.7660
SETUP
SETUP MENU
LENS LENS
EXPOSURE ↵ SHUTTER/AGC
WHITE BAL. WHITE BAL
BACKLIGHT BACKLIGHT
DAY&NIGHT PICT ADJUST ↵
DPC ↵ D-WDR
SPECIAL ↵ DAY/NIGHT
RESET ↵ LANGUAGE
EXIT NEXT ↵
EXIT ↵ SAVE ALL
To select a menu item, tilt the lever vertically ? ; to change
the value or to select an option, tilt the lever horizontally
↵
? . When the symbol appears behind a menu item or
option, the lever can be pressed to call up a submenu or
to activate a function.
All adjustment options can be found in the menu table
or . To save any changes you may have made: in menu
SAVE ALL
, select the item and press the lever; in menu
, the changes are automatically saved when the menu
is exited.
To exit the menu, select the item EXIT.
5 Specifications
Image sensor: . . . . . . . . . CCD chip, 8.5 mm ( 1
Number of pixels / Resolution
VIEWEX-640: . . . . . . . 500 × 582 / 420 lines
VIEWEX-650/850: . . . . 752 × 582 / 540 lines
VIEWEX-670/870WDR: 752 × 582 / 700 lines
Copyright © by MONACOR INTERNATIONAL. All rights reserved.
Lens
VIEWEX-640/650,
VIEWEX-670WDR: . . . 4 – 9 mm/ 1 : 1.2
VIEWEX-850/870WDR: 6 – 15 mm/ 1 : 1.2
Minimum illumination (colour)
VIEWEX-640: . . . . . . . 0.1 lx
VIEWEX-650/670WDR,
VIEWEX-850/870WDR: 0.5 lx
Video output: . . . . . . . . . . PAL, 1 Vpp/75 Ω
S / N ratio: . . . . . . . . . . . . . > 48 dB (AGC off)
IR LEDs, range
VIEWEX-640/650,
VIEWEX-670WDR: . . . 42 LEDs, 40 m
VIEWEX-850/870WDR: 36 LEDs, 50 m
Power supply
VIEWEX-640: . . . . . . . 12 V , 430 mA
VIEWEX-650/670WDR: 12 V , 450 mA
VIEWEX-850/870WDR: 12 V , 540 mA
Admissible temperature: . −10 to +50 °C
IP rating: . . . . . . . . . . . . . IP 66
⁄ ")
3
Dimensions, weight
VIEWEX-640/650,
VIEWEX-670WDR: . . . 90 × 88 × 160 mm, 500 g
VIEWEX-850/870WDR: 110 × 100 × 187 mm, 700 g
Subject to technical modification.
A-1633.00.01.01.2015