Specifications - Kenwood KR-A5050 Instruction Manual

Specifications (FortheU.S.A. a ndCanada)
L!i Caution: Read this page carefully to
ensure safe operation.
[AUDIO section]
Rated power output (FTC)
STEREO MODE
100 watts per channel minimum RMS, both channels
driven, at 8 il from 20 Hz to 20,000 Hz with no more
than 0.06 % total harmonic distortion.
Total harmonic distortion
0.03 % (1 kHz, 50 W, 8 il)
Signal to noise ratio
(lHF'66)
PHONO (MM) 73 dB
LINE (CD,TAPE, VIDEO) 100 dB
Input sensitivity / impedance
PHONO (MM) 2.5 mV / 47 kil
LINE (CD, TAPE, VIDEO) 200 mV /47 kil
Tone control
BASS :!: 10 dB (at 100 Hz)
TREBLE :!: 10 dB (at 10 kHz)
Loudness control (volume at -30 dB level)
" + 9 dB (100 Hz)
[FM tuner section]
Tuning frequency range 87.5 MHz - 108 MHz
Usable sensitivity (MONO at 75 il) ..0.95 !l V /10.8 dBf
50 dB quieting sensitivity (at 75Q)
MONO 2.0 !l V /17.2 dBf
STEREO 25.0 !l V / 39.2 dBf
Total harmonic distortion (at 1 kHz)
MONO 0.4 % (65 dBf input)
STEREO
""""""""""""""""""'" 0.5
% (65 dBf input)
Signal to noise ratio (at 1 kHz)
MONO
"""""""""""""""""""'"
78 dB (65 dBf input)
STEREO 73 dB (65 dBf input)
Stereo separation
1 kHz... 45 dB
Selectivity (:!:400 kHz) 50 dB
Frequency response (30 Hz
-
15 kHz)
+ 0.5 dB, -2.0 dB
[AM tuner section]
Tuning frequency range .." 530 kHz - 1,700 kHz
Usable sensitivity 16 !l V / (400 !l V/m)
Signal to noise ratio (at 30% mod. 1mV input) 50 dB
Total harmonic distortion
" 0.5
%
Selectivity 23 dB
[General]
Power consumption 2,5 A
AC outlet
SWITCHED
"
2: (Total 150W max.)
Dimensions W: 440 mm (17-5/16")
H : 129 mm (5-1/16")
D : 379 mm (14-15/16")
Weight (Net) 10.2 kg (22,5 Ib)
For the U.S.A.
FCC WARNING:
This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference
unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment ifan
unauthorized change or modification is made.
-
NOTE:
This equipment has been tested and found to comply with the limits for a Class Bdigital device, pursuant to Part 15 of the FCCRules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause
harmful interference to radio communications, if it is not installed and used in accordance with the instructions. However, there is no
guarantee that interference willnot occur in a particular installation. Ifthis equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- - Reorient or relocate the receiving antenna.
- - Increase the separation between the equipment and receiver.
- - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- - Consult the dealer or an experienced radiolTVtechnician for help.
Note:
KENWOOD followsa policyof continuous advancements in development. For this reason specifications may be changed without notice.
,,- . -~-~ ,--, 1Q