UNIVIEW MS8500-E Quick Manual

Media switch server
Hide thumbs Also See for MS8500-E:

Advertisement

Quick Links

MS8500‐E 
Media Switch Server
Quick Guide
Manual Version: P100‐20140307  
 
 

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MS8500-E and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for UNIVIEW MS8500-E

  • Page 1 MS8500‐E  Media Switch Server Quick Guide Manual Version: P100‐20140307      ...
  • Page 2 © 2014, Zhejiang Uniview Technologies Co., Ltd. and its licensors  All Rights Reserved  No part of this manual may be reproduced or transmitted in any form or by any means without prior  written consent of Zhejiang Uniview Technologies Co., Ltd.  Notice  The information in this manual is subject to change without notice. Every effort has been made in  the preparation of this manual to ensure accuracy of the contents, but all statements, information,  and recommendations in this manual do not constitute the warranty of any kind, express or implied.   Environmental Protection   This  product  has  been  designed  to  comply  with  the  environmental  protection  requirements.  The  storage, use, and disposal of this product must meet the applicable national laws and regulations.  Safety and Compliance Information  Conventions Used Symbol  The symbols in this chapter are shown in the following table. They are used to remind the reader of  the safety precautions during equipment installation and maintenance.  Safety Symbol  Description  Generic alarm symbol: To suggest a general safety concern.    ESD protection symbol: To suggest electrostatic‐sensitive equipment.    Electric shock symbol: To suggest a danger of high voltage.       Safety Information  WARNING!    Installation and removal of the unit and its accessories must be carried out by qualified personnel.
  • Page 3 To reduce the risk of fire or electrical shock, do not expose this product to rain or moisture.   This  installation  should  be  made  by  a  qualified  service  person  and  should  conform  to  all  the  local codes.   Please  install  blackouts  equipment  into  the  power  supply  circuit  for  convenient  supply  interruption.    The separate earthing terminal must be permanently connected to earth.  For AC supplied model: The plug‐socket combination must be accessible at all times as it serves  as the main disconnecting device.  Before the power cable is installed or removed, the power must be turned off.  To avoid heat accumulation, good ventilation is required for a proper operating environment.    Improper use or replacement of the battery may result in hazard of explosion. Please use the  manufacturer recommended battery type.    Caution: Fiber optic ports – optical safety.     ...
  • Page 4 LVD/EMC Directive    This  product  complies  with  the  European  Low  Voltage  Directive  2006/95/EC  and  EMC  Directive  2004/108/EC.   WEEE Directive–2002/96/EC    The product this manual refers to is covered by the Waste Electrical & Electronic Equipment (WEEE)  Directive and must be disposed of in a responsible manner. ...
  • Page 5: Table Of Contents

    Contents  1 Product Introduction  ∙ ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 1   Appearance  ∙ ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 1   Ports and Buttons ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 2   LEDs and Nixie Tubes ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 4   System Specifications∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 7   Factory Default Settings for Network Parameters  ∙ ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 7   2 Hardware Installation  ∙ ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 9   Installation Procedure  ∙ ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 9   Preinstallation Check ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 10   Removing the Front Panel ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 11   Installing the Device in a 19‐inch Cabinet  ∙ ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 11   Preinstallation Check  ∙ ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 11   Installation Procedure ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 11   Installing the Device on a Workbench ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 14  ...
  • Page 6 Copying and Extracting the Software Package  ∙ ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 26   Running the Upgrade Script ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 27   Software Uninstallation ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 27   Software Reinstallation  ∙ ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 28   6 FAQs ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 29   How to Replace a Hard Disk?  ∙ ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 29   Preinstallation Check  ∙ ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 29   Installation Procedure ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 30     ii ...
  • Page 7: Product Introduction

      1   Product Introduction  The  MS8500‐E  Media  Switching  server  (referred  to  as  MS8500‐E)  is  a  hardware/software  server  based  on  the  IP  Multimedia  Operating  System  (IMOS)  and  oriented  toward  IP‐based  video  surveillance systems. The MS8500‐E uses the Media Switch 3.0 (MS3.0) software.   Appearance  The actual appearance of the MS8500‐E may be different from the illustrations below.  Figure 1‐1 Front view      Figure 1‐2 Rear view      1 ...
  • Page 8: Ports And Buttons

      Ports and Buttons  Figure 1‐3 Ports and buttons on the rear panel  12 13   1: AC input (for PSU 0)  2: Power (for PSU 1)  3: Network Interface Card (NIC) slot  4: VGA video output  5: HDMI video output  6: USB (× 4)  7: Serial port 1 (RS‐232)  8: Serial port 2 (RS‐232)/Serial port 3 (RS‐485)  9: GE port 1  10: GE port 2  11: FE port  12: Power on/off button  13: Reset button   14: Grounding terminal    For detailed descriptions of the ports and buttons, refer to Table 1‐1.  Table 1‐1 Port and button descriptions  Port  Description  AC input  100 ‐ 240 V AC, 50 Hz/60 Hz  Standard: 1 slot  Extended power slot  Optional: 2 slots in 1+1 redundancy mode  Two options:  Extended NIC slot  NIC with 4  GE ports (RJ‐45)  NIC with 2  10GE ports (SFP+)  2 ...
  • Page 9   Port  Description  For connection to a VGA display device.  Supported solutions and screen refresh rates:  1920 × 1080, 50P  1920 × 1080, 60P  VGA output  1280 × 720, 50P  1280 × 720, 60P  1280 × 1024, 60 HZ  1024 × 768, 60 HZ   For connection to an HDMI display device.  Supported resolutions and screen refresh rates:  1920 × 1080, 50P  1920 × 1080, 60P  HDMI video output  1280 × 720, 50P  1280 × 720, 60P  1280 × 1024, 60 HZ  1024 × 768, 60 HZ   USBs  For connection to a USB device.  Serial port 1 (RS‐232)  RJ‐45 port for debugging and maintenance purposes.  Serial port 2  RJ‐45 port compatible with RS‐485 and RS‐232 ports.  (RS‐485/RS‐232)  10/100/1000  Mbit/s  adaptive  Ethernet  port  for  connection  to  a  service  GE port  network.  10/100 ...
  • Page 10: Leds And Nixie Tubes

      LEDs and Nixie Tubes  Front Panel LEDs  Figure 1‐4 Front panel LEDs    1: System LED  2: Hard disk status LEDs    Rear panel LEDs and nixie tubes  Figure 1‐5 Rear panel LEDs and nixie tubes    4 ...
  • Page 11   1: Power module LED  2: Heartbeat LED  3: Alarm LED  4: Device status nixie tubes  6: GE port 2 LED  5: GE port 1 LED  7: FE port LINK LED  8: FE port ACT LED    LED and nixie tube descriptions   For descriptions of the LEDs, refer to  Table 1‐2. For descriptions of the nixie tubes, refer to Table 1‐3.  Table 1‐2 LED descriptions  LED  Color  Indication  • Steady green: The system is operating properly.  • Steady yellow: At least one hardware component is  System LED  Green/yellow  faulty.  LEDs SATA2‐SATA5 indicate status of hard disks in slots  2‐5:  • Off: The hard disk is powered off or not installed.  Hard disk status LED  Green  • Steady green: The hard disk is linked.  • Blinking  green:  The  hard  disk  is  reading  or  writing  data. ...
  • Page 12   LED  Color  Indication  • Off: No network connection.  • Steady green: A network connection is established,  and the data transfer rate is 1000 Mbit/s.  • Blinking  green:  The  data  transfer  rate  is  1000  Mbit/s,  and  the  port  is  transmitting  or  receiving  GE port LED  Green/yellow  data.  • Steady yellow: A network connection is established,  and the data transfer rate is 100Mbit/s.  • Blinking yellow: The data transfer rate is 100Mbit/s,  and the port is transmitting or receiving data.  LINK  • Off: No network connection.  Yellow  (Link status  •...
  • Page 13: System Specifications

      Status  Indication  dt blinks  According to S.M.A.R.T, the hard disk temperature is out of the normal  range. In this case, you need to check the dust filter.  System Specifications  NOTE!    The specifications are subject to change without prior notice.    Table 1‐4 System specifications  Item  Description  Height  2 U (86.1mm)  86.1 mm x 446 mm x 500 mm (excluding the mounting  Dimensions (H x W x D)  brackets and slide rails)  Number of fans   4   • Standard: <12 kg  Weight  • Maximum: <14 kg  Overall power consumption  Maximum: 200 W  Maximum number of hard disks  4   Hard disk type  SATA II  0°C to 40°C  Working temperature  Recommended range: 10°C to 35°C  Working humidity  20% to 80% (non‐condensing)  Storage temperature  ‐20°C to +60°C  Storage humidity ...
  • Page 14   Item  Description  IP address/subnet mask: 192.168.0.12/255.255.255.0  GE port 1  Default gateway: None. GE port 2  Obtains an IP address through DHCP.  Extended network  Obtains an IP address through DHCP.  port (optional)   Host name  The host name is “Localhost”.    8 ...
  • Page 15: Hardware Installation

      2   Hardware Installation  This chapter describes the hardware installation procedure.  Installation Procedure  Figure 2‐1 Installation flowchart  Begin Preinstallation check Requirements  met? Remove front panel Install the device Install hard disk Install front panel Install extended NIC Connect cables     9 ...
  • Page 16: Preinstallation Check

      Preinstallation Check  Checking device components  Check  the  device  model  and  accessories  delivered  along  with  the  package  to  ensure  that  all  the  device  components  are  complete  and  intact.  For  details  about  the  device  model,  and  types  and  quantities of accessories, see the packing list.  Checking installation tools  Prepare the following tools:  Straight screwdriver and cross screwdriver  Antistatic wrist strap or gloves  Checking the installation site  The device must be installed indoors, and the lightning protection and grounding requirements must ...
  • Page 17: Removing The Front Panel

      Removing the Front Panel  Figure 2‐3 Removing the front panel     Installing the Device in a 19‐inch Cabinet  Preinstallation Check  Check  the  grounding  and  stability  of  the  cabinet.  Ensure  that  the  cabinet  has  sufficient  weight‐bearing capacity for the device, and no obstacle is affecting the installation inside or around  the cabinet.  Before installing the device in a standard 19‐inch cabinet, check that:  The cabinet is properly grounded and stabilized.  The weight‐bearing capacity of the cabinet is sufficient to support the device, and no obstacle  inside or around the cabinet will affect the device installation.  The cabinet door is not a glass door.  The cabinet is supported by a bracket instead of rollers.  Installation Procedure  Planning the installation position in the cabinet  Plan the space and position according to the height (2 U) of the device and the number of devices  you want to install. If the cabinet is equipped with a tray, use the tray for the installation. If no tray is  available, use slide rails.   This  procedure  takes  slide  rails  as  an  example.  Figure ...
  • Page 18   Figure 2‐4 Installed device in the cabinet   Rear mounting bracket  Slide rail  Front mounting bracket    12 ...
  • Page 19   Attaching the slide rails to the cabinet   Figure 2‐5 Installing the slide rails       NOTE!    You can extend the slide rails to fit the cabinet.    13 ...
  • Page 20: Installing The Device On A Workbench

      Mounting the device onto the slide rails    CAUTION!    Ensure that the device perfectly aligns with the U marks on the mount bars and is in full contact with the tray or the slide rails. A gap between the device and the tray or the slide rails will cause  instability of the device and may affect its operation stability. For hard disks, instability may cause damage and increase read/write errors.    1. Place the device onto the slide rails and then push the device slightly into place.   2. Align  the  screw  slots  on  the  device  with  the  screw  holes  on  the  cabinet,  insert  the  screws  through the holes and then tighten the screws.  Figure 2‐6 Securing the device to the cabinet using screws        Installing the Device on a Workbench   If a 19‐inch cabinet is not available, you may directly place the device on a clean workbench.   Before installing the device on the workbench, check that:  The workbench is firm enough to bear the weight of the device and the cables.  The workbench is stabilized and properly grounded.  Room of at least 30 cm in the front and at the back of the device, and at least of 10 cm on both ...
  • Page 21: Installing The Hard Disks

      No other object is placed on the device.  Installing the Hard Disks  The  slots  for  hard  disks  are  inside  the  device,  so  you  need  to  remove  the  front  panel  and  the  dustproof cover first.  Preinstallation Check  Carefully read the instructions for the hard disks included in the package.  Use an antistatic wrist strap or antistatic gloves throughout the procedure.  Installation Procedure  Removing the dust filter  Figure 2‐7 Removing the dust filter        Inserting the hard disk  Unpack the hard disk, and then slowly insert it into the hard disk slot.    NOTE!    Two hard disks are delivered with the device and should be installed in slots 2 and 3.    15 ...
  • Page 22: Installing The Front Panel

      Figure 2‐8 Inserting the hard disk      Pushing the hard disk in place with your thumb  When the hard disk is inserted halfway, slowly push the hard disk with your thumb till it clicks into  place.  Figure 2‐9 Pushing the hard disk in place with your thumb    Installing the Front Panel  Attach the front panel to the front of the device and then tighten the captive screws.  Figure 2‐10 Installing the front panel      Installing the Extended Network Interface Card (Optional)  Two  types  of  extended  network  interface  cards  (NICs)  are  allowed.  You  may  choose  either  type  as  required:  NIC with 2 10GE ports (SFP+)  NIC with 4 GE ports (RJ‐45)  16 ...
  • Page 23: Connecting Cables

      The following procedure takes an NIC with two 10GE ports as an example: Remove the filler panel,  and then install the extended NIC.  Figure 2‐11 Installing the extended NIC     Connecting Cables  Connecting the RS‐232 Cable  Figure  2‐12  shows  cable  requirements  for  device  maintenance  through  serial  port  1  (RS‐232).  The  DB9 port is connected to the PC, and the RJ‐45 port is connected to serial port 1 on the device.  Figure 2‐12 RS232 cable    17 ...
  • Page 24: Connecting The Grounding Cable

      Connecting the Grounding Cable    WARNING!    Ensure that the device is properly grounded to prevent personal injury and device damage (due to  lightning and interference).     Ensure that the grounding resistance does not exceed 5 ohms, and the grounding cable is not longer  than 30 meters. For more information, refer to YD5098 specifications.  Connect one end of the grounding cable to the grounding terminal of the device, and connect the  other end to a reliable grounding point, as shown in Figure 2‐13.  Figure 2‐13 Connecting the grounding cable      Using a grounding bar in the equipment room    NOTE!    If the cabinet you are using provides a grounding bar, connect the grounding cable of the device to the grounding bar.    If a grounding bar is available in the equipment room, connect the other end of the grounding cable  to the grounding bolt on the grounding bar and then tighten the secure nut, as shown in Figure 2‐14.  Figure 2‐14 Grounding using a grounding bar in the equipment room  (1) Grounding terminal  (2) AC input  (3) Grounding cable  (4) Grounding bar in equipment room      18 ...
  • Page 25   CAUTION!    Do not connect the grounding cable to a fire fighting pipe, heating radiator, or lightning arrester. The grounding cable must be connected to the grounding system of the equipment room.    Using a buried grounding conductor  If the installation environment provides no grounding bar but a mud ground which can be used to  bury a grounding conductor, you may bury a angle steel (or pipe) at least 0.5 m long into the ground  and use the  buried angle  steel (or pipe) for grounding purpose.  The grounding cable of the device  must be connected and soldered to the steel angle (or pipe), and the joint point should be protected  with anti‐corrosion treatment. Figure 2‐15 shows how the grounding cable should be connected  Figure 2‐15 Grounding using a buried grounding conductor  (1) Grounding terminal  (2) AC input  (3) Grounding cable   (4) Earth    (5) Angle steel or steel pipe    Grounding through the protection earthing (PE) cable of AC power  If neither a grounding bar nor a mud ground is available, connect the grounding cable of the device  to the PE cable in the manner as shown in Figure 2‐16. In addition, make sure that the PE cable of AC  power is properly grounded in the power distribution room or on the  AC power transformer side  Figure 2‐16 Grounding through the PE cable of AC power  (1) Grounding terminal  (2) AC input  (3) AC power cable  (4) Power transformer ...
  • Page 26: Connecting The Power Cable

      Connecting the Power Cable  CAUTION!    Before you connect the power cable, ensure that the power switch is OFF.    Unpack the AC power cable and connect it to power.  For  the  power  socket,  a  three‐wire  single‐phase  power  socket  (as  shown  in  Figure  2‐17)  or  a  multifunctional  computer  power  socket  is  recommended.  The  neutral  point  of  the  power  supply  must  be  properly  grounded.  Generally,  the  neutral  point  of  the  power  system  for  a  building  is  grounded during cabling. Check that the power system of the building is properly grounded. ...
  • Page 27: Basic Configuration

      CAUTION!    To power off the device by pressing and holding the Power On/Off button is not recommended.  4   Basic Configuration  WARNING!    Configuration  operations  shall  be  performed  by  qualified  personnel  only.  Any  random configuration operation may cause severe system faults and loss of data.     Configuration Tasks  Table 4‐1 Configuration task description  Configuration Task  Description  Configuration  Logging in through the Web  Log in to the Web interface.  through Web  Viewing  and  modifying  View and modify parameter settings.  parameter settings  Configuration   Through  Performing service operations  View service status, start, stop and restart service.  command  Viewing system logs ...
  • Page 28: Configuration Through The Command Line Interface

    [root@localhost ~]# mscfgtool.sh serverip 192.168.254.155---192.168.254.155 is the new VM server IP. NOTE!    You can also modify MS8500‐E device ID and VM server IP through the Web interface. For details, refer to MS8500‐E Online Help.    Change Apache port numbers:  NOTE!    You need to modify the port number only when the default port number is already being used.    Run the following command to modify the Apache port number of MS8500‐E:    [root@ localhost ~]# mscfgtool.sh namehost 893--- 893 is the new port number of MS8500-E   For more commands to modify parameter settings, run the mscfgtool.sh ‐help script. After you have  completed the modification, run the msserver.sh restart script to restart service and apply the new  settings.  Performing Service Operations  Viewing service status  [root@localhost ~]# msserver.sh status 22 ...
  • Page 29: Viewing System Logs

      Msserver is running serversnmpd is running DiskReadOnlyCheck is running Msdaemon is running The service status is either running or stopped.  If  the  status  of  a  process  as  shown  above  is  displayed  as  stopped,  you  need  to  restart  the  service  manually. For details, refer to “Restarting the service”.  If an executable file of the server is deleted, or if its executable permission is modified, a "does not  exist" message will be displayed, indicating that the service does not exist. In that case, you need to  reinstall the software.  Starting the service  The MS8500‐E service automatically starts when the software installation is completed. To start the  service manually, use the following command:  [root@localhost ~]# msserver.sh start Stopping the service ...
  • Page 30: Software Upgrade, Uninstallation And Reinstallation

    SSH  client  until  you    have  completed  the  upgrade  or  installation;  otherwise,  the  upgrade  or  installation will fail.    NOTE!    MS8500‐E 192.168.0.30/24 as the IP  When you log in to the   through the SSH client for the first time, use  address of the GE 1 port, 22 as the port number, and use root/uniview as the default user name and password.  Logging In to the Server Through the SSH Client  Icons  as  shown  in  Table  5‐1  appear  on  your  desktop  when  the  installation  of  the  SSH  Secure  Shell  Client software is completed.  Table 5‐1 SSH Secure Shell Client shortcuts  Icon ...
  • Page 31 ,  and  then  in  the  Connect  to  Remote  Host  dialog  box,  type  the  IP  address of the MS8500‐E server as the host name, type root as the user name, keep the default  settings for the rest parameters as shown in Figure 5‐2, and then click  .  Figure 5‐2 Connect to Remote Host dialog box      3. When  the  Enter  Password  dialog  box  as  shown  in  Figure  5‐3  appears,    type  uniview  as  the  password and then click OK to log in to the server.  25 ...
  • Page 32: Software Upgrade

      Figure 5‐3 Enter Password dialog box    Software Upgrade  Strictly follow these steps to ensure a successful software upgrade:  1. Copy and extract the software package.  2. Run the upgrade script.  Copying and Extracting the Software Package  Use the SSH client to copy the package of the new version to a working directory (take /root as an  example) in the current server operating system and then extract the package.  The procedure is as follows:  1. Log in to the server by using the SSH client and then click  . A window appears.  2. In the left pane of the window, select the directory where the installation package (for example,  MS8500‐E)  is  located  and  then  drag  the  package  to  the  /root  directory  in  the  right  pane.  The  package is copied to the server, as shown in Figure 5‐4.  NOTE!    The working directory must be named in English.   ...
  • Page 33: Running The Upgrade Script

      Figure 5‐4 Copying the package to the server      3. Access the directory containing the package and then use the tar command to extract it   [root@localhost ~]# tar zxvf MS8500-E.tar.gz When  the  package  is  extracted,  a  directory  containing  upgrade,  uninstallation  and  reinstallation  scripts is generated.  Running the Upgrade Script  Access the generated directory and run the sh msupdate.sh script by using the following commands:  [root@localhost ~]# cd MS8500-E [root@localhost MS8500-E]# sh msupdate.sh Then follow system prompts to complete the upgrade.  Software Uninstallation  WARNING!    Uninstallation will delete all the related data, so back up all the data before you start. ...
  • Page 34: Software Reinstallation

    [root@localhost MS8500-E]# source msinstall.sh 2013-03-15 15:42:09 : Do not close the terminal during the installation; otherwise, unknown error might occur. MS8500-E installation begins... Please choose the language of MS8500-E (default 0.Chinese): ---Choose a language for the version. 0.Chinese 1.English Please input you choice:1 What version of MS8500-E do you want to install[default:1.
  • Page 35: Faqs

      192.168.254.152 Route initialization succeeded Route initialization succeeded! Begin to install MS8500-E server ... Begin to install rpm pdt_imos ... Install rpm pdt_imos finished... Install rpm pdt_imos succeeded Begin to install rpm MS8500-E ... Install rpm MS8500-E finished... Install rpm MS8500-E succeeded Install succeeded Begin to start MS8500-E server ...
  • Page 36: Installation Procedure

      Installation Procedure  Removing the hard disk  Hold the left and right handle bars in the manner as shown in Removing the hard disk and then pull  the  handle  bars  smoothly  to  disengage  the  hard  disk  from  the  backplane.  Wait  for  at  least  30  seconds till the hard disk stops spinning and then fully remove the hard disk from the slot.    CAUTION!    Use your strength appropriately to avoid damaging the handle bars.    Figure 6‐1 Removing the hard disk      Removing and installing the handle bars  Remove the handle bars from the faulty hard disk and then install them on the new hard disk. Make  sure that you install the left and right handle bars properly.  Figure 6‐2 Removing and installing the handle bars  (1) Left  handle  bar,  marked  with “L”. ...
  • Page 37 BOM: 3101C03P     ...

Table of Contents