Table of Contents
Advertisement
ENGLISH
Hakki Pilke
Eagle
SIRCULAR SAW
- ASSEMBLY INSTRUCTIONS
- OPERATING INSTRUCTIONS
- SAFETY INSTRUCTIONS
- SERVICE INSTRUCTIONS
- SPARE PART LIST
- WARRANTY TERMS
- EC DECLARATION
OF CONFORMITY
MAASELÄN KONE OY
Valimotie 1, 85800 Haapajärvi, Finland
Tel. +358 8 7727300
info@maaselankone.fi,
www.maaselankone.fi
These instructions must be read before
operating the machine!
Advertisement
Table of Contents
Summary of Contents for Hakki Pilke Eagle
-
Page 1: Operating The Machine
ENGLISH Hakki Pilke Eagle SIRCULAR SAW - ASSEMBLY INSTRUCTIONS - OPERATING INSTRUCTIONS - SAFETY INSTRUCTIONS - SERVICE INSTRUCTIONS - SPARE PART LIST - WARRANTY TERMS - EC DECLARATION OF CONFORMITY MAASELÄN KONE OY Valimotie 1, 85800 Haapajärvi, Finland Tel. +358 8 7727300 info@maaselankone.fi,... -
Page 2: Table Of Contents
Transfer Wheels – Exploded View ................27 Spare Part List / Installing the Wheels on the Circular Saw ........27 EC Declaration of Conformity on the Machine ............27 WARRANTY TERMS: ......Virhe. Kirjanmerkkiä ei ole määritetty. Hakki Pilke Eagle Translation Version 5... -
Page 3: The Machine Carries Following Markings
The machine carries following markings ONLY ONE PERSON AT A TIME IN DANGER ZONE BEWARE OF THE CUTTING BLADE THE WORK AREA SHUT DOWN BEFORE BEWARE OF MOVING PARTS RISK OF ENTANGLEMENT WITH MAINTENANCE THE CARDAN SHAFT Hakki Pilke Eagle Translation Version 5... - Page 4 4 (29) USE PROTECTIVE EQUIPMENT READ THE MANUAL BEFORE USE PROTECTIVE EQUIPMENT SCALE MAX RPM LEFT ROTATION RIGHT ROTATION LIFTING POINT FOR HOOK EMERGENCY STOP LIFTING POINT FOR FORKLIFT Hakki Pilke Eagle Translation Version 5...
-
Page 5: General Safety Instructions
The work area, including the ground surface, must be prepared prior to operating the machine to ensure safe working conditions. The Hakki Pilke circular saw with splitting device is designed for making firewood from delimbed trees or other pre-processed wood, such as pre-cut logs. Do not use wood that has been processed in any other way, such as construction waste. -
Page 6: Commissioning A New Machine
Adjust the cradle's extreme position (towards Approx. 3 mm the user) using the nut on the lower part of the cradle. There should be approx. 3 mm between the cradle cover and the rocking cover. Hakki Pilke Eagle Translation Version 5... -
Page 7: Adjusting The Splitting Table
When connecting the PTO shaft, follow the instructions for safe connection provided by the shaft manufacturer. Connecting an unshielded shaft to the machine is strictly forbidden! Hakki Pilke Eagle Translation Version 5... -
Page 8: Electrically Driven Circular Saw With Splitting Device
The machine is equipped with a 4 kW electric motor and is fitted with a safety switch and start/stop switch. The plug current rating of the machine is 16 A, and the required fuse rating is 10 A (slow). Use of a residual-current device is recommended. Hakki Pilke Eagle Translation Version 5... -
Page 9: Start And Stop Buttons Of The Electrically Driven Model
- The cord coming to the machine must be long enough, and it must not be strained when the machine is moved. Start and Stop Buttons of the Electrically Driven Model The start box is on top of the shaft cover, to the left of the blade. Start box. Hakki Pilke Eagle Translation Version 5... -
Page 10: Test Run
(PTO shaft speed: 540 rpm ). An electrically driven machine rotates automatically at the correct speed! 4. Check that the emergency stop functions properly. See the instructions on operation/testing (page 13) and adjustment (pages 19–20). Hakki Pilke Eagle Translation Version 5... -
Page 11: Processing Firewood - General
- Lift larger logs onto the cross-cut cradle in two steps, as described below. 1. Lift the stump end onto the rollers (always feed large logs stump end first)! 2. Lift the top end. Lift with your legs, not with your back! Hakki Pilke Eagle Translation Version 5... - Page 12 - Cutting more than one log at a time, e.g. log bundles, is strictly forbidden! - Never stop the saw blade by forcing a piece of wood or other object against the side or teeth of the saw blade. Hakki Pilke Eagle Translation Version 5...
-
Page 13: Processing Firewood
If the log is warped, knotty, gnarly, too long, or otherwise dangerous to process as-is, pre- process the log with a chain saw to make it safe to put through the firewood processor. 5. Pull the cross-cut cradle to its rear position and place the log in the cradle. Hakki Pilke Eagle Translation Version 5... -
Page 14: Splitting
Hold the log in place with one hand only during the initial stage of splitting when the wood is pushed towards the splitting cone, as shown below. Hakki Pilke Eagle Translation Version 5... - Page 15 – the log can jump free of the rack and cause injury! - Always stand in this position while log splitting ALWAYS STAND BEHIND THE NEVER POSITION YOURSELF: WOOD WHEN SPLITTING ABOVE THE LOG OR BESIDE THE RACK Hakki Pilke Eagle Translation Version 5...
-
Page 16: Emergency Stop Device
2. CALMLY SWITCH OFF THE MACHINE'S POWER SOURCE. 3. REMOVE THE CAUSE OF DANGER. After removing the cause of the danger, activate the machine by releasing the locking latch and by lifting the emergency stop pedal to its upper position. Hakki Pilke Eagle Translation Version 5... - Page 17 REMEMBER! USE THE EMERGENCY STOP PEDAL IN A DANGER SITUATION ONLY! NEVER USE IT FOR SERVICING PURPOSES, E.G. WHILE SHARPENING THE SAW BLADE! NOTE! Models with an internal combustion engine are equipped with a separate emergency stop device! Hakki Pilke Eagle Translation Version 5...
-
Page 18: Removing A Log Stuck On The Splitting Cone
- a badly dulled blade heats up during cutting and may thus lose its pre-stressing; - less cracking between teeth occurs with a sharp blade. - Use for example a 6" v-cut barette file for sharpening. Hakki Pilke Eagle Translation Version 5... -
Page 19: Blade Setting
Removing the Saw Blade Always wear gloves when handling the blade, taking care not to harm yourself, the machine, or the blade. 1. Remove the blade cover hinge bolt and remove the cover. Hakki Pilke Eagle Translation Version 5... - Page 20 (Note! If using a metal object to lock the blade, be careful not to damage the blade teeth!) Hakki Pilke Eagle Translation Version 5...
-
Page 21: Installing The Saw Blade
Remember to wear gloves when handling the blade! Installing the Saw Blade Install the blade by carrying out the removal procedure in reverse order. Remember to install the key in the support flange! Hakki Pilke Eagle Translation Version 5... -
Page 22: Adjusting The V-Belts And Emergency Stop Device
Always start adjusting the belts by loosening the bolts (2 pcs) of the stop block and the stopper attached to it so that the stop block can move while the belts are adjusted. The stop block mounting bolts are located below the splitting cradle. See the figure below. Hakki Pilke Eagle Translation Version 5... - Page 23 4. Open the locking of the adjustment nut. Achieve the correct belt tightness by turning the adjustment nut. Belt tightness: The pulley belts should deflect approx. 15 to 20 mm when pushed down. 5. Tighten the adjustment locking nuts. Hakki Pilke Eagle Translation Version 5...
-
Page 24: Lubrication
- Never carry any extra items on top of the machine during transportation. - Always lower the machine to the ground during breaks en-route, even for short breaks, and especially when leaving the tractor cab unmanned. Storing the Machine Hakki Pilke Eagle Translation Version 5... - Page 25 - The machine must be stored on a level, stable base to prevent tipping. Storing the machine on a slope is strictly forbidden. - Ensure that the machine is protected from collision during storage. Hakki Pilke Eagle Translation Version 5...
-
Page 26: Technical Specifications
Cross-cut cradle length w/ extension 1500 mm 1500 mm Noise level A-weighted sound pressure level 96.0 dB C-weighted sound pressure level 99.5 dB A-weighted sound power level 106.0 dB Vibration Weighted average, m/s 0.20 Hakki Pilke Eagle Translation Version 5... -
Page 27: Tractor-Driven Circular Saw - Exploded View
Name: Timo Jussila Address: Valimotie 1, FI-85800 Haapajärvi, Finland Declares that Hakki Pilke Eagle circular saw with splitting device Serial number:………………………… complies with the relevant provisions of the Machinery Directive (2006/42/EC); Notified body number for Machinery Directive 2006/42/EC: 0504... - Page 28 The guarantee is void if the ownership of the machine is transferred to a third party during the guarantee period The guarantee is void if any of the machine’s seals have been broken Hakki Pilke Eagle Translation Version 5...
- Page 29 This guarantee certificate indicates our responsibilities and obligations in full and it excludes all other responsibilities. Hakki Pilke Eagle Translation Version 5...