1. Manuals
  2. Brands
  3. ETME Manuals
  4. Door Opening System
  5. RDA series
  6. Operating instructions manual

ETME RDA series Operating Instructions Manual

Rolling door operators
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
OPERATING INSTRUCTIONS
ROLLING DOOR OPERATORS

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RDA series and is the answer not in the manual?

Questions and answers

Related Manuals for ETME RDA series

Summary of Contents for ETME RDA series

  • Page 1 OPERATING INSTRUCTIONS ROLLING DOOR OPERATORS...

  • Page 3: Table Of Contents

    The CE declaration and the warranty will void if com- 1. CONTENTS ponents are changed. Contents ............ 3 Only original spare parts and by the manufacturer ap- General instructions ........3 proved accessories shall be used. These parts are Safety-related regulations ......4 used to maintain the quality and safety of the machi- Safety instructions ........

  • Page 4: Safety-Related Regulations

    3. SAFETY-RELATED REGULATIONS NOTICE ! For connecting, programming and servicing, the follo- To avoid damage to the operator and at the door, the drive must be mounted only if: wing regulations must be observed (the list is not ex-  the drive is undamaged, haustive)! ...

  • Page 5: Mounting

     Secure the feather key against sliding 5. MOUNTING  Connect the drive to the shaft 5.1 Preparation  Attach the drive to the bracket  Check that the delivery is complete.  Slide the counter bearing onto the shaft ...

  • Page 6: Anti-Drop Safeguard

    In case of exceeding wear the teeth of the brass worm CAUTION ! wheel (B) may collapse and allow the wheel to turn For operators with weights greater than 20 kg additional underneath the steel worm shaft (A). The pilot wheel aids shall be used, such as hooks or ropes for securing (C) remains unaffected, due to the relative rotation of and lifting.
  • Page 7 7.2 Mechanical limit switch NOTICE ! When mounting the motor cables to ensure that the ME 6 individual wires are inserted deep enough and the (from outside in) (6 cams) screws are tightened so that a firm connection is made. This connection can be checked by pulling the cables.
  • Page 8  Set the switch cam so that the additional limit switch 7.4 Setting the end positions: mechanical limit is actuated. switch  Tighten the locking screw. For the adjustment of the cam an Allen key size 2.5 is required (included with the drive). The cam is fixed on the correct switch position using the locking screw af- Correct the end positions ter positioning (rough setting).
  • Page 9 Assignment Color WARNUNG !  Accidental venting of the brake must be rendered Safety chain in Yellow impossible by preventive measures at the installation RS 485 B Green site. 0 VDC White INFORMATION ! RS 485 A Pink  For safety reasons, brakes in doors without a weight Safety chain out Grey counterbalance must only be vented in the closed...
  • Page 10 7.9 Hand Crank 7.10 Hand chain A insertion aid at the housing of emergency crank By pulling the release lever, the coiler shaft of the handle facilitates the insertion of the crank. hand chain system is shifted and thus switches between motor - and manual operation.
  • Page 11 Depending on the torque of the drive, the chain sys- tem is designed with different sized wheels and with different ratios: Torque Ratio Ø Wheel up to 180 Nm 165 mm up to 300 Nm 200 mm up to 450 Nm 165 mm up to 550/650 Nm 200 mm...

  • Page 12: Technical Data

    8. TECHNICAL DATA Antriebstype TOR- [min Operator Type [Nm] [Nm] [mm] [kW] [mm] [kg] 3~230 3,54 RDA-140.18 5/083 0,55 A/264 3~400 3~230 RDA-180.14 5/083 0,50 A/277 3~400 3~230 RDA-220.14 7/119 0,75 B/328 3~400 3~230 RDA-300.14 7/119 B/328 3~400 3~230 RDA-450.14 7/119 B/341 3~400...

  • Page 13: Drawings

    10. DRAWINGS Maßbild „D“ · Drawing „D“ Maßbild „A“ · Drawing „A“ Maßbild „B“ · Drawing „B“ Maßbild „E“ · Drawing „E“ Maßbild „C“ · Drawing „C“ Maßbild „Notbetätigung“ · „Manual Override“...

  • Page 14: Maintenance

    11. MAINTENANCE / ANNUAL INSPECTION 12. Transport, Storage, Disposal The drive has been fully assembled at the factory, DANGER ! ready wired, tested and packaged. Danger of fatal electric shock! To avoid damage, the transport or storage in the origi- ...

  • Page 15: Declaration Of Conformity

    EN 60335-1  EN 60335-2-103 Manufacturer and technical documentation management ETME GmbH Flohrstr. 33 D-13507 Berlin The relevant technical documentation is compiled in accordance with Annex VII(B) of the Machinery Directive 2006/42/EC. We undertake to transmit, in response to a reasoned request by the market surveillance authorities, this documentation in electronic form within a reasonable period of time.

  • Page 16: Annex

    15. ANNEX – STAR / DELTA CONNECTION The operator in the standard version is suitable as The nominal cross section of the wires in the terminal three-phase motor for 230V/400V operation. is max. 2.5 mm By rewiring is possible to switch the operator from the After reconnecting the rotation direction of the drive factory star connection for 3 ~ 400V to the delta has to be confirmed.
  • Page 20 Operators for Roller Shutters ► Chain Wheel Operators ► PRODUCTS Operators for Sectional Doors ► High-Speed Doors ► Operators for Sliding Gates ► Controls ► Safety Systems ► Accessories ► ETME GmbH | Berlin | Köln | www.etme.de | info@etme.de...

Table of Contents