Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ETME SD series
Summary of Contents for ETME SD series
- Page 1 OPERATING INSTRUCTIONS SECTIONAL DOOR OPERATOR...
-
Page 3: Table Of Contents
Only original spare parts and by the manufacturer ap- 1. CONTENTS proved accessories shall be used. These parts are Contents ............ 3 used to maintain the quality and safety of the machine. General instructions ........3 Changes are only permitted after consultation with the Safety-related regulations ...... -
Page 4: Safety-Related Regulations
3. SAFETY-RELATED REGULATIONS NOTICE ! For connecting, programming and servicing, the follo- To avoid damage to the operator and at the door, the drive must be mounted only if : wing regulations must be observed (the list is not ex- ... -
Page 5: Mounting
Install the torque bracket 5. MOUNTING Insert the feather key into the shaft 5.1 Preparation The shaft end is greased before fitting the drive Check that the delivery is complete. When using collars, slide the collar onto the shaft ... -
Page 6: Initial Operation
6.1 Connection to the control unit CAUTION ! For operators with weights greater than 20 kg additional The operator is factory wired to the control unit. If this aids shall be used, such as hooks or ropes for securing is not the case, proceed as follows: and lifting. - Page 7 6.2 Mechanical limit switch 6.4 Setting the end positions: mechanical limit switch For the adjustment of the cam an Allen key size 2.5 is ME 4 (from outside in) (4 cams) required (included with the drive). The cam is fixed on the correct switch position using the locking screw Safety limit switch open after positioning (rough setting).
- Page 8 Correct the end positions Assignment Color With the fine adjustment screw a readjustment of the Safety chain in Yellow respective end position is possible. RS 485 B Green Check of end positions 0 VDC White Check if the end positions are set correctly and if the RS 485 A Pink operator stops in the corresponding end position.
- Page 9 6.10 Hand crank 6.8 Declutch system A insertion aid at the housing of emergency crank The mounting position of the actuator with unlocking is handle facilitates the insertion of the crank. preferably present in an inverted position (motor poin- ting downwards). 1.
- Page 10 6.11 Hand chain 6.12 Extending or shortening the chain By pulling the release lever, the coiler shaft of the The coil is joined via one or two coupling links (marked hand chain system is shifted and thus switches by color yellow). between motor- and manual operation.
-
Page 11: Technical Data
7. TECHNICAL DATA Antriebstype Operator Type [Nm] [Nm] [Nm] [min [mm] [kW] [kg] SW-55.24 25,4 1~230 0,27 12,0 SW-55.24-E 25,4 1~230 0,27 12,5 3~230 SD-100.24 25,4 0,37 11,0 3~400 3~230 SD-100.24-E 25,4 0,37 2,6 1,5 11,5 3~400 3~230 SD-140.18 25,4 0,55 3,5 2,0 12,0... -
Page 12: Drawings
8. TECHNICAL DRAWINGS Version KU Version E Version KE Mounting points... -
Page 13: Maintenance
9. MAINTENANCE / ANNUAL INSPECTION 10. TRANSPORT, STORAGE, DISPOSAL The drive has been fully assembled at the factory, ready wired, tested and packaged. DANGER ! Danger of fatal electric shock! To avoid damage, the transport or storage in the origi- ... -
Page 14: Declaration Of Conformity
EN 61000-6-3 EN 60335-1 EN 60335-2-103 Manufacturer and technical documentation management ETME GmbH Flohrstr. 33 D-13507 Berlin The relevant technical documentation is compiled in accordance with Annex VII(B) of the Machinery Directive 2006/42/EC. We undertake to transmit, in response to a reasoned request by the market surveillance authorities, this documentation in electronic form within a reasonable period of time. -
Page 15: Annex
The nominal cross section of the wires in the terminal 13. ANNEX - STAR, DELTA CONNECTION is max. 2.5 mm The operator in the standard version is suitable as three-phase motor for 230V/400V operation. After reconnecting the rotation direction of the drive has to be confirmed. - Page 16 Operators for Roller Shutters ► Chain Wheel Operators ► PRODUCTS Operators for Sectional Doors ► High-Speed Doors ► Operators for Sliding Gates ► Controls ► Safety Systems ► Accessories ► ETME GmbH | Berlin | Köln | www.etme.de | info@etme.de...
Need help?
Do you have a question about the SD series and is the answer not in the manual?
Questions and answers