Related Manuals for Trolla 12232
Summary of Contents for Trolla 12232
-
Page 1: Log Splitter
LOG SPLITTER INSTRUCTION MANUAL MODEL NO.:12232 Carefully read the instruction manual before you use this machine, and save this instruction manual for future reference. -
Page 2: Table Of Contents
TABLE OF CONTENTS WARNING SYMBOLS ……… GENERAL SAFETY INSTRUCTIONS …… SPECIAL SAFETY INSTRUCTIONS FOR LOG SPLITTER TECHNICAL SPECIFICATIONS Technical specifications Electrical safety UNPACKING LOOSE PARTS LIST FEATURES 9-10 ASSEMBLY AND OPERATION 10-13 Assembly 10-11 Operation 11-12 Freeing a jammed log Replacing hydraulic oil Sharpening wedge TROUBLE SHOOTING... -
Page 3: Warning Symbols
WARNING SYMBOLS WARNING! Standard graphic symbols are used on all machines in order to ensure complete safety of all parts of the log splitter. As these symbols are very important, read the information below attentively. It is obligatory to read the machine’s use and maintenance manual in full before using the machine. -
Page 4: General Safety Instructions
Warning: never remove a log trapped in the wedge with your hands. Warning: Before carrying out any maintenance operation described in this manual, disconnect the plug of the machine. Warning: voltage as indicated on the rating plate. GENERAL SAFETY INSTRUCTIONS IMPORTANT! When using electrical tools, the following safety instructions should be observed to prevent the risk of electric shock, personal injury and fire. - Page 5 11. Do not abuse cord When tools is used outdoors, use only Never carry tool by cord or yank it to extension cords intended for use outdoors disconnect it from wall outlet. Keep cord and so marked. from heat, oil and sharp edges. 19.
-
Page 6: Special Safety Instructions For Log Splitter
SPECIAL SAFETY INSTRUCTIONS FOR LOG SPLITTER may be dangerous and may seriously 1. The log splitter must always be used by damage the machine. one operator only. 2. Nobody must be allowed to use the log 10. Never attempt to cut two logs at once, one splitter unless they have read the may fly up and hit you. -
Page 7: Technical Specifications
person to help you remove a jammed log. 22. Make sure that the machine and the cable 19. Do not use machines with electric motor if never come in contact with water. natural gas, petrol fumes or other 23. Treat the power cable with care, do not inflammable vapours are present. -
Page 8: Unpacking
electricity provisions, consult an electrician Replacing cables or plugs first. Immediately throw away old cables or plugs when they have been replaced by new ones. It Grounding is dangerous to insert the plug of a loose cable In the event of an electrical short circuit, in the wall outlet. -
Page 9: Loose Parts List
LOOSE PARTS LIST Check all loose parts from the box with the list below. Assemble according to the instruction on the following pages 1. Machine body assembly 2. Rolling wheels 3. Supporting leg 4. Safety guard for ZHB hydraulic control lever 5. -
Page 10: Assembly And Operation
the wood has regular fibers it is not difficult to split logs with diameter greater than the 3. Recommended oils maximum shown in fig. 1. It is important not We recommend use of the following oils for to insist when the log does not split on the the hydraulic cylinder. -
Page 11: Operation
3. Use two screws, elastic washers and flat DO NOT ADJUST THE MAX PRESSURE washers to fasten the safety guard on the LITITING SCREW (14) IN FIG. 4! supporting bracket to protect the ZHB hydraulic control lever. Max pressure was set before the log 4. -
Page 12: Freeing A Jammed Log
excessively hard wood. not place log across the log splitter for splitting. It may be dangerous and may seriously damage the machine. Do not attempt to split 2 pieces of logs at the same time. One of them may fly up and hit you. -
Page 13: Replacing Hydraulic Oil
may launch the log and cause accident. Warning: Never mix oil with general waste! Used oil must be disposed of according to current regulations in the country where the machine is used. Sharpening the wedge After using the log splitter for some time, sharpen the wedge of the log splitter using a fine-toothed file and smooth any burrs or crushed area along the cutting edge. -
Page 14: Trouble Shooting
TROUBLE SHOOTING PROBLEM PROBABLE CAUSE REMEDY SUGGESTED Motor stops Overload protection device disengaged to Let motor cool down, and push the starting protect the log splitter from being damaged button of the overload protection device to re-start the motor Log is improperly positioned Refer to “Log splitter operation”... -
Page 15: Exploded View
EXPLODED VIEW... -
Page 16: Parts List
PARTS LIST Part No. Description Q’ty Part No. Description Q’ty Motor Copper washer 14 Rubber pad O-ring 14×1.8G Nut M8 SpringⅡ Pin φ2.5×4 Controlling valve（GS） Axle sleeve O-ring 11.2×1.8G Casting iron plate Controlling shaft Steel ring 10 Sealing ring 5.6×1.8G Steel ballφ2.5 SpringⅠ...
Need help?
Do you have a question about the 12232 and is the answer not in the manual?
Questions and answers