Table of Contents
Advertisement
Quick Links
80V P
OWER
E
LECTRONIC
OPERATION MANUAL
There are important set-up / operational instructions which must be
followed to ensure the safe and effective operation of your 80V
Read this manual carefully before installing the system.
This manual covers the following models:
PAC51380V
PAC122880V
PAC143580V
PAC235080V
PACFB80V
PAC9080V
This manual concerns the operation of the 80V Power System only. For
instructions on the operation of the Pacific luminaire fixture, please also
refer to the additional instruction sheet.
THANK YOU FOR PURCHASING A SELECON PACIFIC LUMINAIRE. WE HAVE DESIGNED THIS
LUMINAIRE TO PROVIDE YOU WITH A SUPERIOR FITTING IN PERFORMANCE, DESIGN &
ENGINEERING. WE ARE CONFIDENT THAT IT WILL PERFORM TO YOUR EXPECTATIONS FOR
MANY YEARS TO COME.
Installation is entirely at your risk.
installation. Do not attempt installation unless you are suitably qualified. If you do not understand
a point in this manual, don't guess. Don't take short cuts. If in doubt, stop! Contact Selecon or
one of its authorised distributors for advice. Don't be afraid to ask for help.
IMPORTANT NOTE: Before discarding the packaging, ensure you have the mounting bolt
set, and high-temperature lens tube locking knob.
Version 1.3: January 2004
S
YSTEM
T
RANSFORMER
system.
80V 5.5° ~ 13° Zoomspot Pacific
80V 12° ~ 28° Zoomspot Pacific
80V 14° ~ 35° Zoomspot Pacific
80V 23° ~ 50° Zoomspot Pacific
80V Fixed beam Pacific
80V 90° Fixed beam Pacific
Caution!
Read this manual from cover to cover before attempting
Advertisement
Table of Contents
Related Manuals for Selecon PAC51380V
Summary of Contents for Selecon PAC51380V
- Page 1 Do not attempt installation unless you are suitably qualified. If you do not understand a point in this manual, don’t guess. Don’t take short cuts. If in doubt, stop! Contact Selecon or one of its authorised distributors for advice. Don’t be afraid to ask for help.
-
Page 2: Table Of Contents
Information in this manual shall not be deemed a warranty, representation or guarantee concerning a luminaires’ suitability or fitness for a specific purpose. Subject to the right to use its luminaires, Selecon does not convey any right, title or interest in its intellectual property, including, without limitation, its patents, copyrights and know-how. -
Page 3: Safety Warnings
The power supply developed for Selecon is an electronic transformer tracking the incoming (dimmed) supply to deliver a maximum of 80V at the lamp. Mains supply input 220 – 240V to be supplied via a high quality entertainment type dimmer. - Page 4 Pacific 80V Manual MOUNTING THE POWER SYSTEM ON THE PACIFIC YOKE First remove the lens tube, then follow the steps below. Step 2 – Attach power supply using mounting bolts and washers supplied with unit. Step 1 – Rotate yoke clockwise Step 3 –...
- Page 5 Pacific 80V Manual WARNING The 80V 1200W lamp generates a considerable heat output. Supplied with each 80V Power System is a high heat resistant lens tube clamp knob, and white teflon washer Replace the current lens tube clamp knob and red fibre washer on the Pacific luminaire with this one. SETUP The Power System is an electronic transformer.
- Page 6 Pacific 80V Manual LAMP SET UP Before inserting a lamp into the module, we suggest that you practice the motion of removing and inserting the lamp holder module from the lamphouse. Front ‘T’ Rear Lip Loosen the thumb-screw at the front of the lamp holder module by about 5mm. Holding the lamp holder module, slide it forward until both the rear lip and the front 'T' of the lamp holder module clear their home positions [1], then pull the lamp module down [2].
-
Page 7: Lamp Mounting
Pacific 80V Manual Lamp Mounting The lamp module is factory set at a mid peak / flat field. Mount the lamp ensuring that the pins are fully pushed home. Fit the module into the luminaire and secure as above. Turn on and make final peak / flat setting as desired – refer notes below on ‘Optimising the Output’ To replace the lamp –... -
Page 8: Lamps
Only replace damaged parts with authorised Selecon spares. N.B. Luminaire Cable - Your Selecon luminaire is fitted with special heat resistant flexible cable, replace with genuine Selecon spare part cable kit only - refer to your Selecon distributor. (Replacement cables... -
Page 9: Limited Warranty
If Selecon accepts the warranty claim, Selecon will provide, or arrange for, service, repair or replacement as Selecon shall determine in its sole discretion. Selecon shall bear the cost of such service, repair or replacement. However, the owner shall bear the cost of freight and insurance on the luminaire, both ways. - Page 10 Contacting Selecon Selecon New Zealand Ltd. 19-21 Kawana Street, Northcote Auckland, New Zealand Tel: 64-9-481 0100, Fax: 64-9-481 0101 e-mail: selecon@seleconlight.com website: www.seleconlight.com Please contact Selecon, or check our web site to find the Selecon distributor nearest to you.