Table of Contents
Advertisement
PVM-2130QM
RM-668
Ij]
norm
(normal)
key
Press
this
key
to return to
the
standard
setting.
•This
key
is
effective
oniy
for
the
controi
keys
on
the
left.
[2]
HUE
control
keys
Press the
GRN
(green)
key
to
make
the skin
tones
greenish or the
PUR
(purpie)
key
to
make
it
purplish.
•
These
controi
keys
are
effective
for
the
NTSC
and
NTSC
443
coior
systems
only.
[
3
]
COLOR
control
keys
Press the
+
key
to
make
the color
intensity
vivid
or the
-
key
to
make
it
pale.
[
4
]
BRIGHT
(brightness) control
keys
Press the
+
key
to
make
the
picture brighter or
the
-
key
to
make
it
darker.
[s]
SHARP
(sharpness)
control
keys
Press the
+
key
to
obtain
a sharp
picture or
the
-
key
to
obtain
a
soft picture.
Q]
BALANCE
control
keys
Press the
L
key
to
increase the
sound volume
of
the
left
speaker
or the
R
key
to
increase the
sound volume
of
the
right
speaker.
[T]
Coior
system
indicators
PAL,
SECAM,
NTSC, NTSC443
The
color
system
of
the input signal
is
automatically
selected
and
the
corresponding
indicator illuminates.
When
the
input signal
is
monochrome,
no
color
system
indicator illuminates.
[T]
MUTING
indicator
Illuminates
while the
sound
is
muted.
•
Muting
is
controlled only
by
the
Remote Commander.
H]
STANDBY
indicator
Illuminates
when
the
power
is
turned
off
by
the
Remote
Commander.
Ql
POWER
switch
Press
this
switch
to turn
the
monitor
on.
Press
this
switch again
to turn
it
off.
•
When
the
monitor
is
turned
on,
the settings
of
the
monitor
are the
same
as
when
it
was
last
turned
off.
•
For
a few seconds
after
turning
on
the
monitor
the color
of picture
may
vary
because
the white
balance
is
adjusted
at this time.
This
is
not
a problem.
Qi]
Remote
control
detector
The
beam
from
the
Remote
Commander
(s
received
here.
im
CONTROL
key
Press
this
key
to illuminate
the
keys
and
indicators
on
the
front
panel.
Press
this
key again
to
extinguish
them.
[H
VOLUME
control
keys
Press the
+
key
to raise
the
volume
or the
-
key
to
lower
it.
[
1
^ PICTURE
control
keys
Press the
+
key
to
make
the
contrast, color
intensity
and
brightness stronger or the
-
key
to
make
them
weaker.
[m
Input select
keys
LINE
A,
LINE
B,
VTR, AV, DIGITAL
Select the input
source connected
to
the
LINE
A,
LINE
B,
VTR,
AV
or
DIGITAL
RGB
connector.
When
a key
is
pressed:
•
it
blinks
if
the other
indicators
and
keys
on
the
front
panel
illuminate.
•
it
illuminates
if
they are extinguished.
Key
illumination
For the keys
Q] through
0,
[13]
and
[14]:
•
While
each
key
is
pressed,
it
blinks,
indicating
that
adjustment
is
going
on.
•
During adjustment,
if
the
adjustment
value reaches the
limit,
the
blinking
speed
becomes
slower.
5
Hide quick links:
Advertisement
Table of Contents
