Advertisement
Table of Contents
Congratulations on purchasing
your new Hunter® ceiling fan! It will
provide comfort and performance
in your home or office for many
years. This installation and operation
manual contains complete
instructions for installing and
operating your fan.
We are proud of our work and
appreciate the opportunity to
supply you with the best ceiling fan
available anywhere in the world.
To register your fan, please visit:
www.HunterFan.com/register
Save your receipt for proof of purchase.
Switch Housing
What to Expect with
Your Installation
30 inches
7 feet
2
Downrod
6
Light Kit
13
14
M3641-01 • 12/20/16 • © 2016 Hunter Fan Company
Tools Needed
Mounting Options
Ladder
3
Wiring
Canopy
9
Maintenance
Remote Control
& Cleaning
16
1
www.HunterFan.com
1.888.830.1326
Ceiling Bracket
4
5
Blades
11
12
Troubleshooting
?
?
?
19
20
Advertisement
Table of Contents
Related Manuals for Hunter Hepburn
Summary of Contents for Hunter Hepburn
- Page 1 To register your fan, please visit: www.HunterFan.com/register Save your receipt for proof of purchase. Maintenance Switch Housing Light Kit Remote Control & Cleaning Troubleshooting M3641-01 • 12/20/16 • © 2016 Hunter Fan Company...
-
Page 2: What To Expect With Your Installation
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. M3641-01 • 12/20/16 • © 2016 Hunter Fan Company... -
Page 3: Tools Needed
The symbols can be used to identify Power Drill 9/64” Drill Bit the appropriate hardware for each step. Screwdrivers (optional) (optional) If mounting to a support structure, you will also need these tools. M3641-01 • 12/20/16 • © 2016 Hunter Fan Company... -
Page 4: Mounting Options
You need BOTH You need ONLY a Longer a Longer Downrod & Downrod an Angled Mounting Kit *most common M3641-01 • 12/20/16 • © 2016 Hunter Fan Company... -
Page 5: Ceiling Bracket
To avoid possible electrical shock, before 1-888-830-1326. installing your fan, disconnect the power by turning off the circuit breakers to the outlet Refer to warning w.1 on pg. 2 box associated with the wall switch location. M3641-01 • 12/20/16 • © 2016 Hunter Fan Company... - Page 6 Steps 1-5 to remove standard downrod pipe Longer Downrod for angled ceilings or ceilings 10’ or higher Shorter Downrod for fans installed close to ceiling Steps 6-10 to reassemble with new pipe M3641-01 • 12/20/16 • © 2016 Hunter Fan Company...
- Page 7 4-5 full turns) until it stops. with pliers. DO NOT can be inserted. from the top of the downrod. HAND TIGHTEN. 8” 3/8” If the setscrew is not tightened securely, the fan may fall. M3641-01 • 12/20/16 • © 2016 Hunter Fan Company...
- Page 8 DO NOT PICK THE FAN UP BY THE through the canopy. Let CANOPY OR WIRES. Place the downrod the canopy sit loosely on ball into the slot in the ceiling bracket. top of the fan. M3641-01 • 12/20/16 • © 2016 Hunter Fan Company...
- Page 9 Spread the wires apart, with the grounded wires on one side of Refer to CAUTION c.1 on pg. 2 the outlet box and the ungrounded wires on the other side of the outlet box. M3641-01 • 12/20/16 • © 2016 Hunter Fan Company...
- Page 10 Spread the wires apart, with the grounded wires on one side of Refer to CAUTION c.1 on pg. 2 the outlet box and the ungrounded wires on the other side of the outlet box. M3641-01 • 12/20/16 • © 2016 Hunter Fan Company...
- Page 11 Lift the canopy into place so that Insert the two canopy screws lifted into place, the canopy fits into the screw holes are aligned. found in the hardware bag. the hanging bracket as shown. M3641-01 • 12/20/16 • © 2016 Hunter Fan Company...
- Page 12 Blades www.HunterFan.com 1.888.830.1326 Attach each blade to a blade iron using the blade washers, found in the hardware bag, and the blade assembly screws, found in the hardware bag. M3641-01 • 12/20/16 • © 2016 Hunter Fan Company...
-
Page 13: Switch Housing
Make sure the upper switch housing is securely attached to the mounting plate. Failure to properly secure all 3 assembly screws could result in the switch housing fixture falling. M3641-01 • 12/20/16 • © 2016 Hunter Fan Company... -
Page 14: Light Kit
Make sure the lower switch housing is securely attached to the upper switch housing. Failure to properly secure all three assembly screws could result in the light fixture falling. M3641-01 • 12/20/16 • © 2016 Hunter Fan Company... -
Page 15: Operation Instructions
Attach the glass bowl to the light kit See next page for fan by twisting it clockwise until it snaps operation instructions. into place. M3641-01 • 12/20/16 • © 2016 Hunter Fan Company... -
Page 16: Wall Control
This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. M3641-01 • 12/20/16 • © 2016 Hunter Fan Company... - Page 17 Reference the included remote function card for information on how to use your wall control! IMPORTANT Use the pull-chain switch on the fan to set the fan speed to the HIGH position before operation. M3641-01 • 12/20/16 • © 2016 Hunter Fan Company...
- Page 18 Fan Speed Control Control Long Long Light High Fan High Press Press Long Long Light Low Fan Low Press Press Long Dimming Mode Press On/Off Power On/Off Long Pair Function Press M3641-01 • 12/20/16 • © 2016 Hunter Fan Company...
- Page 19 - move the reverse switch brushes or cloths to prevent to the opposite position. You will scratching. Cleaning products need to remove the glass to do so. may damage the finishes. M3641-01 • 12/20/16 • © 2016 Hunter Fan Company...
-
Page 20: Troubleshooting
• Install a fresh battery. the switch housing. your remote controls, please go to www.HunterFan.com/FAQs and click “How do I properly install multiple remote-controlled fans?” for information on how to correct this issue. M3641-01 • 12/20/16 • © 2016 Hunter Fan Company...