Subscribe to Our Youtube Channel
Related Manuals for King Industrial KC-13HPC
Summary of Contents for King Industrial KC-13HPC
- Page 1 13” PLANER WITH HELICAL CUTTERHEAD 08/2016 INSTRUCTION MANUAL MODEL: KC-13HPC COPYRIGHT © 2016 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.
-
Page 2: Warranty Information
WARRANTY INFORMATION 2-YEAR kING CANADA TOOLS LIMITED WARRANTY OFFERS A 2-YEAR LIMITED WARRANTY FOR THIS 13” PLANER INTENDED FOR NON COMMERCIAL USE PROOF OF PURCHASE Please keep your dated proof of purchase for warranty and servicing purposes. REPLACEMENT PARTS Replacement parts for this product are available at our authorized King Canada service centres across Canada. LIMITED TOOL WARRANTY King Canada makes every effort to ensure that this product meets high quality and durability standards. - Page 3 GENERAL & SPECIFIC SAFETY RULES 1. kNOW YOUR TOOL watch) because they could get caught in moving parts. Non-slip Read and understand the owners manual and labels affixed to the footwear is recommended. Wear protective hair covering to contain tool. Learn its application and limitations as well as its specific po- long hair.
- Page 4 14) Torx adjustment wrench 6) 2-1/2” dust chute adaptor 15) 4mm hex. key 7) Height adjustment handle 8) Planing thickness scale & indicator Specifications MODEL KC-13HPC 13” Maximum planing width Maximum planing thickness 6” Number of cutter inserts Feed rate...
-
Page 5: Electrical Information
ELECTRICAL INFORMATION WARNING! ALL ELECTRICAL CONNECTIONS MUST BE DONE BY A QUALIFIED ELECTRICIAN. FAILURE TO COMPLY MAY RESULT IN SE- RIOUS INJURY! ALL ADJUSTMENTS OR REPAIRS MUST BE DONE WITH THE MACHINE DISCONNECTED FROM THE POWER SOURCE. FAILURE TO COMPLY MAY RESULT IN SERIOUS INJURY! POWER SUPPLY RESET bUTTON (thermal overload protector) WARNING: YOUR PLANER MUST BE CONNECTED TO A 110V-120V, 15-... -
Page 6: Assembly And Operation
ASSEMbLY & OPERATION WARNING! TO REDUCE THE POTENTIAL FOR PERSONAL INJURY AND/OR DAMAGE TO THE MACHINE, BEFORE ASSEMBLING MAKE SURE THE MA- CHINE IS TURNED OFF AND THE PLUG IS NOT CONNECTED TO A POWER SOURCE. DO NOT TURN ON OR PLUG IN THE MACHINE UNTIL INSTRUCTED TO DO SO AFTER ALL ASSEMBLY STEPS IN THIS MANUAL HAVE BEEN COM- PLETED. -
Page 7: Operation & Adjustments
OPERATION & ADJUSTMENTS Using and adjusting the pre-set depth stops continued..The pre-set depth stop Fig.8 is adjusted at the factory, but in some rare cases it may eventually be necessary to readjust. To adjust the pre-set depth stops: 1. Set the pre-set depth stop to the 1” position by sliding the knob (A) Fig.8. 2. - Page 8 bASIC GUIDELINES basic guidelines This 13” planer with helical cutterhead is designed to remove material from the top surface of a board in order to bring the board down to a specific desired thickness. To obtain even, uniform thickness across the length of a board, the stock being planed must have one face that has already been machined per- fectly flat (usually on a planer) and the stock should be fed with this flat face against the table.
-
Page 9: Maintenance
MAINTENANCE MAINTENANCE WARNING! TO REDUCE THE POTENTIAL FOR PERSONAL INJURY MAKE SURE THE MACHINE IS TURNED OFF AND HAS BEEN UN- PLUGGED BEFORE PERFORMING ANY MAINTENANCE OPERATIONS. Regular Maintenance To ensure optimum performance and longer service life of your planer the following basic maintenance steps should be practiced regularly: 1) Inspect the power chord and plug for damage before each use. - Page 10 MAINTENANCE Replacing/Rotating Cutterhead Inserts continued... 5) While preventing the cutterhead from turning, remove each of the cutter inserts (A) Fig.15 with the supplied Torx wrench (B). 6) Before replacing or rotating the inserts take a moment to clean the screw housing, inserts (if rotating rather than replacing), and screws with a solvent such as lac- quer thinner.
- Page 11 MAINTENANCE belt replacement continued... 5) Remove the two cap screws (A) Fig.19 located in the top of the right cover (C) using a 5 mm hex. key. 6) Remove the centre panel (B) Fig.19 and the right cover (C). FIGURE 19 7) Remove the flat head allen screw (B) Fig.8 with the supplied 4 mm hex.
Need help?
Do you have a question about the KC-13HPC and is the answer not in the manual?
Questions and answers
My 13 HPC cutterhead spins but the feed rollers do not. What is wrong?
If the cutterhead spins but the feed rollers do not on the King Industrial KC-13HPC planer, the issue could be a failure in the feed roller drive mechanism. This may include a broken or disengaged drive belt, gear, or chain that connects the motor or cutterhead to the feed rollers. It could also be due to a worn or damaged internal part that transfers motion to the feed rollers.
This answer is automatically generated
Hi My KC-****HPC will not start .I have full power to it
The King Industrial KC-13HPC may not start despite having full power due to the thermal overload protector. If the motor overheats, a safety mechanism automatically stops it. The planer has an overload reset button next to the On/Off switch. Pressing this button may reset the motor and allow it to start again. Additionally, ensure the planer is properly connected to a 110V-120V, 15A circuit breaker, as incorrect wiring can prevent operation.
This answer is automatically generated