Do you have a question about the GL5000 and is the answer not in the manual?
Questions and answers
Marcus Haynes
May 20, 2025
Receiver problem
1 comments:
Mr. Anderson
May 24, 2025
Common receiver problems with the Guardline GL5000 include:
1. Receiver not powered on or not plugged in. 2. Receiver batteries are low or depleted. 3. LED on the receiver is not lit or flashing (should be solid red or blue above zone 1 when powered). 4. Volume on the receiver is turned down. 5. Inconsistent alarms due to sensors not being properly paired. 6. Multiple receiver conflicts causing pairing issues.
Solutions include checking power and batteries, turning up the volume, resetting and re-pairing sensors, and resolving receiver conflicts.
This answer is automatically generated
Linda Landis
April 27, 2025
Sensor is not sending signal to receiver. Sensor sees movement but receiver does not sound alarm.
1 comments:
Mr. Anderson
May 14, 2025
If the Guardline GL5000 sensor detects movement but does not send a signal to the receiver, press the Test button to check if the sensor is correctly paired with the receiver. If needed, use the Test button to recode the sensor when more than one receiver is used.
This answer is automatically generated
Tom Roche
February 26, 2025
How do you change an alarm on a sensor already having another alarm sound installed?
1 comments:
Mr. Anderson
February 26, 2025
To change the alarm sound on a Guardline GL5000 sensor, follow the steps in section 2.3, "Pairing your Sensor and Receiver," with both your sensor and receiver nearby. If done correctly, you will hear a double beep on your receiver confirming that a new melody has been set.
Page 2
Thank you for purchasing a Guardline Driveway Alarm! This B. Powering your Receiver and Sensor driveway alarm has a quarter mile range and is great for multiple Receiver applications, including: alerting you when visitors enter your The main power source for the receiver is the included 12v/500mA AC/DC driveway, deterring trespassers and thieves from entering your power adapter.
C. Pairing your Sensors with a Receiver D. Installing your Sensor Your sensor(s) need to be paired with a receiver before your system will It is recommended that the motion sensor be mounted at least 3 feet from the ground on a sturdy, non-metal surface (i.e. a wall or stiff post) with function.
E. Battery Check Procedures Helpful Tips 1. When one or more of the sensor batteries are low, the low-battery indicator LED will blink every 5 seconds. Resetting your Zones If you completely relocate your sensors (for example, if you were to move to a new home and reinstall your alarm system in a different arrangement, or have incorrectly paired your sensor(s) and receiver), follow these steps to clear sensors from a zone so you can then re-pair the sensors in a new arrangement.
Trouble Shooting Issue Cause Solution Issue Cause Solution Check that sensor has working Move sensor and/or receiver batteries that are installed Sensor or Receiver are Sensor and/or receiver not away from electrical properly and receiver is receiving electrical powered on transformers or other cause of plugged in or has batteries and interference...
Page 6
F. Advanced Settings: Sensor Adjustments C. After detecting motion, the sensor can “sleep” for either 7 or 30 seconds, Several switches are inside the battery compartment which regulates allowing an object to pass through the field of vision without setting the alarm off various sensor functions.
• COM: Neutral/Grounding terminal. • NC (Normal Closed): Outputs to an open circuit when the selected zone has Though your Guardline Driveway Alarm System is factory set to suit the most com- been triggered. mon user, sometimes your needs may require more complicated settings. For in- •...
Need help?
Do you have a question about the GL5000 and is the answer not in the manual?
Questions and answers
Receiver problem
Common receiver problems with the Guardline GL5000 include:
1. Receiver not powered on or not plugged in.
2. Receiver batteries are low or depleted.
3. LED on the receiver is not lit or flashing (should be solid red or blue above zone 1 when powered).
4. Volume on the receiver is turned down.
5. Inconsistent alarms due to sensors not being properly paired.
6. Multiple receiver conflicts causing pairing issues.
Solutions include checking power and batteries, turning up the volume, resetting and re-pairing sensors, and resolving receiver conflicts.
This answer is automatically generated
Sensor is not sending signal to receiver. Sensor sees movement but receiver does not sound alarm.
If the Guardline GL5000 sensor detects movement but does not send a signal to the receiver, press the Test button to check if the sensor is correctly paired with the receiver. If needed, use the Test button to recode the sensor when more than one receiver is used.
This answer is automatically generated
How do you change an alarm on a sensor already having another alarm sound installed?
To change the alarm sound on a Guardline GL5000 sensor, follow the steps in section 2.3, "Pairing your Sensor and Receiver," with both your sensor and receiver nearby. If done correctly, you will hear a double beep on your receiver confirming that a new melody has been set.
This answer is automatically generated