DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 1 Safety Precaution 1.1. General guidelines 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 2 Warning 2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatic Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatic Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistor-sand semiconductor "chip"...
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 2.3. Service caution based on legal restrictions 2.3.1. General description about Lead Free Solder (PbF) The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this equipment in considering the globally environmental conservation.
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 5 Location of Controls and Components Followings are the Location of Controls and Components for DMR-EH585EG as a sample. For other model, refer to each Operation Instructions.
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 6 Operation Instructions 6.1. Taking out the Disc from DVD-Drive Unit when the Disc cannot be ejected by OPEN/CLOSE button 6.1.1. Forcible Disc Eject 6.1.1.1. When the power can be turned off. 1. Turn off the power and press [STOP] [CH UP] keys on the front panel simultaneously for 5 seconds.
Page 14
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 6.1.2. When the Forcible Disc Eject can not be done.
Page 15
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 1. Turn off the power and pull out AC cord. 2. Remove the Top Case. 3. Put deck so that bottom can be seen. 4. Remove the sheet of the bottom side. 5. Slide SLIDE CAM by Eject Pin (JZJ0484) or minus screw driver (small) in the direction of arrow to eject tray slightly.
Page 16
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 7. It is necessary to paste the Sheet again after ejection of the disc. Refer to the illustration of the Step 4 and below fugure about the portion of pasting the Sheet. Note: Use the replacement parts (RMV0335) when the Sheet has not being stickability.
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 7 Service Mode 7.1. Self-Diagnosis and Special Mode Setting 7.1.1. Self-Diagnosis Functions Self-Diagnosis Function provides information for errors to service personnel by “Self-Diagnosis Display” when any error has occurred. U**, H** and F** are stored in memory and held.
Page 18
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG Error Code Diagnosis contents Description Monitor Display Automatic FL display No error information Initial setting for error code in memory No display No display (Error code Initialization is possible with error code initialization and main unit initialization.)
Page 19
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG Error Code Diagnosis contents Description Monitor Display Automatic FL display [HDD ERR] is displayed when a) When normal start up was failed. No display ERROR start up of HDD was failed. b) When start up at HDD boot was failed.
Page 20
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG Item FL display Key operation Mode name Description Front Key Aging Perform sequence of modes as * Aging Display following the then mode. When the power is ON, press Description shown below continually. [STOP], [POWER]...
Page 21
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG Item FL display Key operation Mode name Description Front Key Progressive initialization The progressive setting is initialized to display before execution When the power is on (E-E mode), Interlace. leaves. press [STOP] [PLAY] simultaneously for 5 seconds.
Page 22
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG Item FL display Key operation Mode name Description (Remote controller key) RTSC Return in XP AV1 input signal is encoded (XP), decoded Initial mode: EE2/ Interlace/ XP/ Press [1] [3] in service mode. (A & V)
Page 23
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG Item FL display Key operation Mode name Description (Remote controller key) READ SEEK Inspecting seek time of HSS to inspect At start Press [3] [1] in service mode. Inspection performance. * When canceling the inspection mode while executing, do “forced...
Page 24
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG Item FL display Key operation Mode name Description (Remote controller key) READ VERIFY Measure of access time in READ VERIFY At start Press [3] [2] in service mode. Inspection MODE of HDD. * When canceling the inspection mode while executing, do “forced...
Page 25
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG Item FL display Key operation Mode name Description (Remote controller key) HDD High Speed Scan Press [3] [6] in service mode. The [*] sign is added every 10 seconds while inspecting. Two digits on the right side are the progress level of the inspection (The unit is %).
Page 26
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG Item FL display Key operation Mode name Description (Remote controller key) RAM Drive Last Error RAM Drive error code display. 1. Error Number is displayed for 5 Press [4] [2] in service mode. *For details about the drive error code, refer seconds.
Page 27
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG Item FL display Key operation Mode name Description (Remote controller key) Front connection Press all front keys and check the connection Press [5] [4] in service mode. inspection between Main P.C.B. and Front key Switches.
Page 28
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG Item FL display Key operation Mode name Description (Remote controller key) USB check Display the volume label of the USB memory. When memmory Press [7] [5] in service mode. connected. When USB check is OK.
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 8 Service Fixture & Tools Part Number Description Compatibility RFKZ0260 Extension Cable (MainP.C.B. - RAM/Digital P.C.B. Module/ 88 Pin) Same as EH50 Series RFKZ0327 Extension Cable (MainP.C.B. - Power P.C.B./ 15 Pin) Same as E55 Series RFKZ0125 Extension FFC (HDD - RAM/Digital P.C.B.
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 9 Disassembly and Assembly Instructions 9.1. Disassembly Flow Chart The following chart is the procedure for disassembling the casing and inside parts for internal inspection when carrying out the servicing. To assemble the unit, reverse the steps shown in the chart below.
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 9.4.1. How to assemble Tray door ass’y 9.3. Top case 1. Attach the Tray door spring to Tray door ass’y. 1. Remove the 2 screws (A) and 3 screws (B). 2. Slide Top Case rearward and open the both ends at rear side of the Top Case a little and lift the Top Case in the direction of the arrows.
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 9.5. Front (L) P.C.B., Front (R) 9.6. HDD, ATAPI P.C.B. P.C.B. 1. Remove the 2 Screws (A) to remove the Front (L) P.C.B. and Front (R) P.C.B.
Page 34
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 1. Remove the 2 Screws (A) and (B), FFC and Wire with connector to remove HDD with ATAPI P.C.B.. CAUTION: When replacing HDD, pay attention as below. 2. Put HDD with HDD angle up and down inversely so as not to give a shock to HDD.
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 9.7. RAM/Digital P.C.B. Module 1. Remove the 3 Screws (A) and Screw (B) to remove Digital Shield. 3. Put Digital P.C.B. on DVD drive and remove RAM/Digital P.C.B. Module. 2. Lift up Digital P.C.B. slightly so to disconnect connectors to Note: remove Digital P.C.B..
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 9.8. DV Jack P.C.B., USB SD P.C.B. 1. Remove 2 Screw (A) and connector to remove DV Jack P.C.B. and USB SD P.C.B.
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 9.9. Rear Panel 9.10. Power P.C.B. 9.9.1. Only Fan Motor 1. Remove 3 Screws (A) and disconnect the connector to remove Power P.C.B.. 1. Remove the 2 Screws (C) and fan connector, remove the Fan motor with pushing 2 tabs in the direction of arrows.
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 9.11. HDMI P.C.B. 9.12. Main P.C.B., SW P.C.B. 1. Push the PCB spacer in the direction of arrows and lift up 1. Remove 5 Screws (A). HDMI P.C.B. slightly so to disconnect connector to remove 2.
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 10 Measurements and Adjustments 10.1. Service Positions Note: For description of the disassembling procedure, see the section 9. 10.1.1. Checking and Repairing of Power P.C.B.
Page 40
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 10.1.2. Checking and Repairing of RAM / Digital P.C.B. Module...
Page 41
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 10.1.3. Checking and Repairing of Main P.C.B.
Page 42
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 10.1.4. Checking and Repairing of HDD...
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 10.2. Caution for Replacing Parts 10.2.1. Items that should be done after replacing parts...
Page 44
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG Note3: Please prepare latest firmware updating disc. * Main Firm is being recorded in HDD, but new HDD has no data. Writing Procedure of Main Firm: <<Caution>> (1) Writing of Main Firm needs 3, 4 minutes.
Perform auto recording and playback for one minute using the RAM No abnormality should be seen in the picture, sound or operation. disc. *Panasonic DVD-RAM disc should be used when recording and playback. Model with the HDD: Perform auto recording and playback for one No abnormality should be seen in the picture, sound or operation.
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 11.2. Analog Video Block Diagram :REC SIGNAL :PB SIGNAL IC3001 (VIDEO PROCESSOR) MAIN P.C.B. JK3903 (SW1) (SW2) 6MHz COMP P59001 P7402 C OUT DM 6MHz BIAS 12MHz (SW3) P59001 P7402 Y OUT DM 6MHz COMPONENT...
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 11.3. Analog Audio Block Diagram :REC SIGNAL :PB SIGNAL MAIN P.C.B. JK3001 REAR JACK D4005 Q4006 MIX L OUT2 MUTE LINE OUT Q4007 QR4002 (AUDIO MUTE DRIVE) MUTE MIX R OUT2 FROM XTMUTE TIMER D4006...
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 11.4. Analog Timer Block Diagram FRONT (R) P.C.B. IC7501 T7501 IC7701 (TIMER) DISPLAY HEATER POWER SWITCHING MAIN P.C.B. TRANSFORMER REMOTE CONTROL RECEIVER QR7402 CTL. D7506 IP7501 P SAVE HEATER+ +38V UNREG.+38V to TU7802- (IC PROTECTOR)
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 11.5. HDMI Block Diagram IC56103 VIDEO EE SIGNAL (HDMI TRANSMITTER) VIDEO PB SIGNAL AUDIO EE SIGNAL AUDIO PB SIGNAL P55003 P56103 P55003 P56103 P55003 P56103 P55003 P56103 P55003 P56103 P55003 P56103 HDMI P55003 P56103 CONNECTOR...
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 12.10. AV I/O (4/4) Section (Main P.C.B. (2/4)) Schematic Diagram (AV) EE GG LL MM NN FF HH REAR_JACK JK3001 AV I/O SECTION (2/4) Rear LB3007 R OUT R IN C3062 R3008 C3059 LB3008 Rear...
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 12.18. DV Jack Schematic Diagram 12.20. Front (L) Schematic Diagram TO P7001 SW P.C.B. PP7701 DV JACK K1KA06B00150 P37002 TO P7401 K1FY104B0006 MAIN P.C.B. (MAIN NET (3/4)SECTION) P37001 RET2 K1KA05A00479 TPB- TPB- TPB+ TPB+ OPEN...
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 13.5. Front (L) P.C.B., Front (R) P.C.B., SW P.C.B. and DV Jack P.C.B. Front (L) P.C.B. SW P.C.B. DMR-EH58EC/EP,EH585EG DMR-EH58EC/EP,EH585EG Front (L) P.C.B. SW P.C.B. (VEP70222A) (VEP70225A) Front (R) P.C.B. DV Jack P.C.B. DMR-EH58EC/EP,EH585EG DMR-EH58EC/EP,EH585EG Front (R) P.C.B.
DMR-EH58EC / DMR-EH58EP / DMR-EH585EG 14 Appendix for Schematic Diagram 14.1. Voltage and Waveform Chart Note) Circuit voltage and waveform described herein shall be regarded as reference information when probing defect point, because it may differ from an actual measuring value due to difference of Measuring instrument and its measuring condition and product itself.