Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for FlyTech K738
Summary of Contents for FlyTech K738
- Page 1 User Manual Version 1.0 February, 2015 K738/K746/747 Panel PC Hardware System...
- Page 2 Copyright 2015 All Rights Reserved Manual Version 1.0 The information contained in this document is subject to change without notice. We make no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
- Page 3 Safety IMPORTANT SAFETY INSTRUCTIONS To disconnect the machine from the electrical Power Supply, turn off the power switch and remove the power cord plug from the wall socket. The wall socket must be easily accessible and in close proximity to the machine. Read these instructions carefully.
- Page 4 and for all STATIONARY EQUIPMENT, the material of a FIRE ENCLOSURE, in the thinnest significant wall thickness used, shall be of 5VB CLASS MATERIAL or shall pass the test of Clause A.1 LEGISLATION AND WEEE SYMBOL 2012/19/EU Waste Electrical and Electronic Equipment Directive on the treatment, collection, recycling and disposal of electric and electronic devices and their components.
- Page 5 Revision History Revision Date Description V1.0 February, 2015 Release...
-
Page 6: Table Of Contents
Table of Content 1 Item Checklist ............1 1-1 Standard Items ................1 2 Specification ............2 3 System View ............4 3-1 Front View & Side View ..............4 3-2 Rear View & Side View ..............5 3-3 ... -
Page 7: Item Checklist
Item Checklist 1-1 Standard Items a. System x 1 b. Power connector x 1 c. RS-232 connector x 2 d. GPIO/RS-232/422/485 connector x2 e. Ground cable x 1 f. Mounting bracket kit x 10 g. Key x 2 h. Rubber strip x 1 i. -
Page 8: Specification
Specification Model K738 K746 K747 Motherboard Processor Celeron J1900 2.0GHz L2 2M (10W) Core Logic Built-in SoC 1 x DDR3L SO-DIMM slot, FSB 1066/1333MHz System Memory Default 4GB RAM (Max 8GB) Graphic Memory Intel Graphic DX11.1 LAN1 Controller Intel WG I211AT... - Page 9 1(option) RFID 1(option) Rear I/O Power Switch Power in "+" , "GND" , "Chassis GND" (3 pin pitch 5mm Terminal Block) DVI-D RS-232 2 (8x2 pitch 3.81mmTerminal Block w/ screw) 9(8+1GND) (9x2 pitch 3.81mm Terminal Block w/ screw) GPIO 4ch Digital input ; 4ch Digital output RS-232/422/485 9(8+1NC) (9x2 pitch 3.81mm Terminal Block w/ screw) 2 x Gigabit Ethernet (RJ-45)
-
Page 10: System View
System View 3-1 Front View & Side View Description Touch screen WIFI/RFID/NFC Antenna (option) Key lock USB 2.0 Power switch... -
Page 11: Rear View & Side View
3-2 Rear View & Side View Description Cable clamp Groove for mounting clip 3-3 Top View Description WIFI antenna (option) -
Page 12: Dimension
3-4 Dimensions K746 (12.1’) 300mm (cut-out dimension) - Page 13 K747 (15’) 375mm (cut-out dimension)
- Page 14 K738 (18.5’) 474mm (cut-out dimension)
-
Page 15: I/O View
3-5 I/O View Number Description Power switch Power input DVI-D COM6 (RS-232/422/485) 4 x DI, 4 x DO COM1 (RS-232) COM2 (RS-232) Line-out Mic-in... -
Page 16: Connector Pin Definition
3-6 Connector PIN Definition RS-232/422/485 mode changed by BIOS setting RS-232/422/485 Pin Define RS-232 Pin Define RS-232 RS-422 RS-485 DATA- DATA+... -
Page 17: Install The Panel Mount
Install the Panel Mount Mounting method that mounts product into an opening of mounting wall from the front and secured from the rear. The installation steps are as follow: Assemble the mounting bracket kits. Put the rubber strip on the rear side of the panel mount product as shown in the picture above. - Page 18 Put the panel mount product in the cut-out (dimension: 375mm x 333mm) from the front side of mounting wall, with the sides of the front bezel shown on the outside. Use provided mounting bracket kits (x10) to attach and tighten the panel mount product to the mounting wall as picture shown above.
-
Page 19: Configuration
Configuration RS-232/422/485 Setting 1. Power on the system, and press the <DEL> key when the system is booting up to enter the BIOS Setup utility. 2. Select the Advanced tab. 3. Select VGA/COM Power Configuration Ports and press <Enter> to go to display the available options. -
Page 20: Appendix: Driver Installation
Appendix: Driver Installation The shipping package includes a Driver CD. You can find every individual driver and utility that enables you to install the drivers in the Driver CD. Please insert the Driver CD into the drive and double click on the “index.htm” to pick the models.