Advertisement

Edition 4, From serial no. 106000-
Publ. no 4872223-00
OM 3110, 2012-02
Orwak 3110
OPERATING INSTRUCTIONS (IN THE ORIGINAL)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 3110 and is the answer not in the manual?

Questions and answers

Summary of Contents for Orwak 3110

  • Page 1 Edition 4, From serial no. 106000- Publ. no 4872223-00 OM 3110, 2012-02 Orwak 3110 OPERATING INSTRUCTIONS (IN THE ORIGINAL)
  • Page 2 English CONTENTS SAFETY Please read the operating instructions BEFORE operating the machine. Our warranty/product responsibility requires that: Safety....• instructions are followed, and that no conversion or modification is carried Control panel..out. Operating • original spare parts, and hydraulic oils and lubricants recommended by the machine manufacturer are used.
  • Page 3 English RANGE OF APPLICATION The machine is a hydraulically operated baler intended for compacting bulky materials such as cardboard, paper and plas- tic. The machine may only be used in areas that have a roof, protection against wind, and normal lighting. The machine is intended for use within the temperature range -10°C to +40°C. A low-temperature oil and/or heater should be used at tempera- tures lower than +5°C. Materials that are flammable or of an explosive nature, such as pressurised containers or the like, which could cause injury, damage, fire or an explosion if exposed to pressure or sparks, must not be compacted in the machine. CONTROL PANEL Voltage light - this Temperature lights light indicates that Blue lights indicate that the there is power to the machine is cold.
  • Page 4 (If the machine is set to “AUTO” the press plate will lower automatically and stop UNDER PRESSURE against the bale in its down position, and step 13 will be skipped.) 13 Lower the press plate using the down arrow. The press plate will automatically stop in its down position and keep the bale UNDER PRESSURE. 14 Tie the straps. 15 Raise the press plate back up using the up arrow. 16 Open the doors and remove the bale using the bale cart. http://www.orwak.se/~/media/Movies/3110.ashx...
  • Page 5 English INSTALLATION Box 58 576 22 Sävsjö Sweden Type Serial No Product No Date Weight WEEKLY INSPECTION AND MAINTENANCE NOTE! During inspection and maintenance, servicing and the removal of trapped waste etc: 1. Set to manual mode (MAN) on the control panel. 2. Disconnect the power to the machine by removing the plug from the wall socket. 3. Do not work inside the machine. TROUBLESHOOTING: First, check: OVERLOAD PROTECTION NORMAL TRIPPED FUSE SAFETY CHECKS - Check the shutter switch: it must not be possible to start the machine if the upper shutter is open/opened.
  • Page 6: Specifications

    English TECHNICAL 3110 (mm) DIMENSIONAL DIAGRAM SPECIFICATIONS (490 3110-00) GENERAL DATA Total weight: 340 kg Transport height: 1,990 mm Dimensions: Height: 1,990 mm Width: 866 mm Depth: 680 mm Depth with open door: 1,365 mm Recommended space for machine in operation (working area): Height: 1,990 mm Width:...
  • Page 7 Tel: 46-382-15700 Tel: 46-382-15700 Fax: 46-382-10607 Telefax: 46-382-10607 declare under our sole responsibility that the product model (serial number specified on the first page) 4903110-00 – 4903110-99 4903110-S001 – 4903110-S999 to which this declaration relates is in conformity with the following standards or other normative documents in accordance with the provisions of Directives 2006/42/EEC (Machinery Directive) 2004/108/EEC (EMC Directive) 2006/95/EC (Low Voltage Directive) 2009/125/EC ErP Directive (Energy-related Products) 3110 (mm) The machine fulfils the requirements of PL = c and category 1 according to EN ISO 13849-1:2008 EN 60204-1 (Safety of Machinery – Electrical Equipment of Machines) EN 61000-6-1 (EMC Immunity for residential, commercial and light-industrial environments) EN 61000-6-2 (EMC Immunity for industrial environments) EN 61000-6-3 (EMC Emission standard for residential, commercial and light-industrial environments) EN 61000-6-4 (EMC Emission standard for industrial environments) EN ISO 13849-1 (Safety of Machinery – Safety-related parts of control systems) Sävsjö 2012-02-01 Arne Isaksson Product Manager and compiler of technical documentation 13 7...
  • Page 8 Leader in compaction and baling solutions Orwak is a world leader in compaction and baling solu make all the di erence. When you partner with Orwak, tions for solid waste material at source. We develop, you also gain access to the vast experience we have manufacture and market a comprehensive range of built up since 1971.

Table of Contents

Save PDF