Download Print this page
Hide thumbs Also See for Dani Extreme V2+:

Advertisement

Quick Links

Dani Extreme V2+
manual

Advertisement

loading
Need help?

Need help?

Do you have a question about the Dani Extreme V2+ and is the answer not in the manual?

Questions and answers

Summary of Contents for dicodes Dani Extreme V2+

  • Page 1 Dani Extreme V2+ manual...
  • Page 2 It is equipped with an OLED display, has a power output of up to 40W (up to 12V or 15A at the coil), and provides the option of temperature controlled vaping with many different kinds of wire-materials— dicodes- (RESISTHERM NiFe30), nickel, titanium, stainless steel, resistance-wire and many others.
  • Page 3: Display Operation

    03 Display Operation The MOD is equipped with an OLED display which provides status information during the vape and/or for 4 seconds after each vape. Temperature controlled mode (TC-mode): Battery-voltage during Temperature during the vape the vape (including voltage Other modes: battery symbol drop during vape).
  • Page 4 05 Main Menu (Page 1) Power Up and Power Down Power Up increases the power to the Power-Limit value and then rolls over to 5W. Power Down decreases the power down to 5W and then rolls over to the Power-Lim value.
  • Page 5 When Hctrl is set to 1, the menu directly jumps to the selection of the wire type. Here the user can select between dicodes-wire (NiFe30), Nickel 200, Titan, Tungsten (Wolfram), Stainless Steel (Inox) and “Other”. With “Other” selected, the temperature coefficient defined in the Extended Functions Menu under item “Tmp.
  • Page 6 Note: If the power setting equals the power limit value, the boost has no function since the values are the same. For a diagram of boost operation options, see the document “Explanations referring to the Power Boost on dicodes mods.” Commented [SC2]: LOCATION? WEBSITE?
  • Page 7 05 Main Menu (Page 4) Switch Off Device In addition to the Auto-Power-Off feature, the user can turn off the device manually. It is recommended that the user turn off the device wait for auto-power-off, replacing the battery in order to preserve the statistic counters. Otherwise the statistics collected since the last power up will be lost.
  • Page 8 (*1 ) The temperature coefficient is determined by the type of wire material, and the resistance must be in the range of 100 to 650: When TC-mode is selected (Main menu HCtrl=1), the user must select the wire type to be NiFe30 (dicodes wire), Ni200, Titanium, Tungsten (Wolfram), Stainless Steel (Inox) or “Other”.
  • Page 9 (the current drained depends on the power at the coil). In contrast to other available tube- and box-mods on the market, which stop operation already at 3.4V, the lower discharge level on dicodes mods lead to better battery utilization (about 20% better).
  • Page 10 06 Extended Functions Menu The display mode shows several parameters during the vape. With display mode =1 in Temperature Controlled Mode, the parameters shown are temperature, coil resistance, temperature regulating power and battery voltage. For standard, boost and heater protection modes the parameters shown are the selected power (static, no change), the coil resistance and the battery.
  • Page 11 06 Extended Functions Menu The Extended Functions Menu has another sub-menu showing several statistical values. There are two types of value-counters, either re-settable to zero or not. The statistic counters are saved whenever the mod is automatically or manually switched off. In contrast, if the battery is removed from the mod before switching off, the changes of the counters since the device was most recently turned on.
  • Page 12 GmbH Friedrich der Große 70 D-44628 Herne Germany Phone: +49 2323 1463635 Email: info@dicodes-mods.de Web: www.dicodes-mods.de Errors excepted. Subject to changes without prior notice. c copyrights dicodes GmbH, Germany, no unauthorized reprint. 10.09.2015 dicodes DaniV2plus manual, ENG, revision 1...