Software Upgrade; Troubleshooting & Tips - Nevir NVR-7400-32HD-N Instruction Manual

(Now) : Shows the current programme.
(RECORD): The TV will start to record the
selected programme. You can press again to stop
the recording.
More event info
P+P- :
IMPORTANT: Connect a USB disk to your TV while the TV
is switched off. You should then switch on the TV to enable
the recording feature.
Note: Switching to a different broadcast or source is not
available during a recording.
Programme Options
In EPG menu, press the OK button to enter the Event
Options menu.
Select Channel
In EPG menu, using this option, you can switch to the
selected channel.
Record / Delete Record Timer
After you have selected a programme in the EPG menu,
press the OK button. Select the Record option and press
the OK button. After this operation, a recording will be
scheduled for the selected programme.
To cancel an already set recording, highlight that
programme and press the OK button and select
the option Delete Rec. Timer. The recording will be
cancelled.
Set Timer / Delete Timer
After you have selected a programme in the EPG
menu, press the OK button. Select the Set Timer on
Event option and press the OK button. You can set
a timer for future programmes. To cancel an already
set timer, highlight that programme and press the OK
button. Then select "Delete Timer" option. The timer
will be cancelled.
Note: It is not possible to record two channels at the same
time.

Software Upgrade

Your TV is capable of fi nding and updating automatically
via the Aerial/Cable signal.
Software upgrade search via user interface
Simply navigate on your main menu. Choose Settings and
select Other Settings menu. In Other Settings menu navigate
on to the Software for Upgrade item and press OK button to
check for a new software upgrade.
3 AM search and upgrade mode
While the TV is connected to an aerial signal. If
Automatic scanning in the Upgrade Options menu
is enabled, the TV wakes up at 03:00 and searches
broadcast channels for new software upgrades. If
new software is found and downloaded successfully,
the next time the TV powers up , it will have the new
software version.
Note: If the TV fails to come on after the upgrade unplug the
TV for 2 minutes and plug in again.
02_MB82_BASIC_[GB]_1900UK_PVR_DVBT-C_NICKEL22_32189LED_BMS_10086716_50257847.indd 26 02_MB82_BASIC_[GB]_1900UK_PVR_DVBT-C_NICKEL22_32189LED_BMS_10086716_50257847.indd 26
Troubleshooting & Tips
Tv will not turn on
Make sure the power cord is plugged in securely to wall outlet.
The batteries in the remote control may be exhausted. Press
the Power button on the TV.
Poor picture
• Have you selected the correct TV system?
• Low signal level can cause picture distortion. Please check
antenna access.
• Check if you have entered the correct channel frequency
if you have done manual tuning.
• The picture quality may degrade when two devices are
connected to the TV at the same time. In such a case,
disconnect one of the devices.
No picture
• No Picture means that your TV is not receiving a
transmission. Have you selected the correct button on the
remote control? Try once more. Also make sure the correct
input source has been selected.
• Is the antenna connected properly?
• Is the antenna cable damaged?
• Are suitable plugs used to connect the antenna?
• If you are in doubt, consult your dealer.
No sound
• Has the TV been set to mute? To cancel mute, press
the " " button, or increase the volume level.
• Sound is coming from only one speaker. Is the balance
set to one extreme? See Sound Menu section.
Remote control - does not operate
• The batteries may be exhausted. Replace the
batteries.
Input sources - can not be selected
• If you cannot select an input source, it is possible
that no device is connected. if not
• Check the AV cables and connections if you have
tried to connect a device.
Recording unavailable
To record a programme, you should fi rst connect a
USB disk to your TV while the TV is switched off.
You should then switch on the TV to enable recording
feature. If you cannot record, try switching off the TV
and then re-inserting the USB device.
USB is too slow
If a "USB is too slow" message is displayed on
the screen while starting a recording, try restarting
the recording. If you still get the same error, it is
possible that your USB disk does not meet the speed
requirements. Try connecting another USB disk.
English - 26 -
16.08.2013 15:02:35 16.08.2013 15:02:35