Table of Contents
Advertisement
ICE TECH SS / SP
Manual
ICE CUBE MAKERS
MODELS:
ICETECH SS / SP 25
ICETECH SS / SP 35
ICETECH SS / SP 45
ICETECH SS / SP 60
ICETECH SS / SP 80
ICETECH SS / SP 135
CAREFULLY READ THE INSTRUCTIONS CONTAINED IN THIS MANUAL SINCE THEY PROVIDE IMPORTANT
INFORMATION RELATIVE TO SAFETY DURING INSTALLATION, USE AND MAINTENANCE.
1
TECHNICAL SERVICE MANUAL
Technical Service
Advertisement
Table of Contents
Related Manuals for IceTech SP 25
Summary of Contents for IceTech SP 25
- Page 1 Technical Service Manual TECHNICAL SERVICE MANUAL ICE CUBE MAKERS MODELS: ICETECH SS / SP 25 ICETECH SS / SP 35 ICETECH SS / SP 45 ICETECH SS / SP 60 ICETECH SS / SP 80 ICETECH SS / SP 135 CAREFULLY READ THE INSTRUCTIONS CONTAINED IN THIS MANUAL SINCE THEY PROVIDE IMPORTANT INFORMATION RELATIVE TO SAFETY DURING INSTALLATION, USE AND MAINTENANCE.
-
Page 2: Table Of Contents
ICE TECH SS / SP Technical Service Manual TABLE OF CONTENTS INTRODUCTION ............................... 3 1.1. Warnings ..............................3 1.2. Description ..............................4 1.3. Operating principle ............................ 4 1.4. Wiring diagram ............................7 SPECIFICATIONS ............................8 2.1. Installation diagrams for inlet/outlet tubes and dimensions ..............8 2.2. -
Page 3: Introduction
ICE TECH SS / SP Technical Service Manual 1. INTRODUCTION 1.1. Warnings This appliance should be installed by approved Technical Service Personnel. This plug should be accessible at all times. To reduce the risk of electrical shock, ALWAYS disconnect the machine BEFORE cleaning or maintaining the equipment. -
Page 4: Description
ICE TECH SS / SP Technical Service Manual 1.2. Description Main Features of the Machine Anti-blocking spray nozzles. Pump without seals. High pressure safety pressostats even in air-cooled machine. Large condensers (work well at high ambient temperatures; and reduce cooling water consumption in water-cooled machines). - Page 5 ICE TECH SS / SP Technical Service Manual which closes the circuit with 3. A different blue wire goes to 2 on terminal G1 which at this moment is connecting 1 and 4. A red wire connects bin thermostat T1 and micros G1 and G2 which close the circuit with 4 and provide current via G1 to the timer G.
- Page 6 ICE TECH SS / SP Technical Service Manual...
-
Page 7: Wiring Diagram
ICE TECH SS / SP Technical Service Manual 1.4. Wiring diagram... -
Page 8: Specifications
ICE TECH SS / SP Technical Service Manual 2. SPECIFICATIONS 2.1. Installation diagrams for inlet/outlet tubes and dimensions... -
Page 9: Consumption Data, Weights, Crated Dimensions And Volumes
ICE TECH SS / SP Technical Service Manual 2.2. Consumption data, weights, crated dimensions and volumes WEIGHT DIMENSIONS WEIGHT DIMENSION WATER WATER TOTAL COND. MODEL L/Hour FABR. L/Hour L/Hour (KG) X*Y*Z (KG) ICE TECH 350x470x590 0.20 ICE TECH 23.1 350x470x590 0.20 ICE TECH 435x605x695... - Page 10 ICE TECH SS / SP Technical Service Manual HIGH PRESSURE FUSE REFRI. PRESSURE SAFETY TOTAL MODEL CONSUMPTION Kg/cm Kg/cm Kg/cm (GR) ICE TECH ICE TECH ICE TECH ICE TECH ICE TECH ICE TECH ICE TECH ICE TECH ICE TECH ICE TECH ICE TECH 1150 135A...
-
Page 11: Production Tables For Ice Flakers
ICE TECH SS / SP Technical Service Manual 2.3. Production tables for Ice Flakers ICE TECH 25 Tw/Ta ICE TECH 35 Tw/Ta... - Page 12 ICE TECH SS / SP Technical Service Manual ICE TECH 45 Tw/Ta ICE TECH 60 Tw/Ta...
- Page 13 ICE TECH SS / SP Technical Service Manual ICE TECH 80 Tw/Ta ICE TECH 135 Tw/Ta...
-
Page 14: Delivery & Unpacking
ICE TECH SS / SP Technical Service Manual 120, 3. DELIVERY & UNPACKING Upon receipt, thoroughly inspect the packing container. If there appears to be damage to the container contact the shipper immediately. Unpack unit in the presence of delivery personnel noting any damage on the waybill. - Page 15 ICE TECH SS / SP Technical Service Manual...
-
Page 16: Installation
ICE TECH SS / SP Technical Service Manual WARNING: DO NOT LEAVE PACKING MATERIALS (PLASTIC BAGS, CARDBOARD BOXES, ETC.) WITHIN REACH OF CHILDREN. 4. INSTALLATION The ice cube maker is delivered on a small wooden pallet and is protected with a cardboard box and packaging. -
Page 17: Recommended Placement Of Unit
Recommended placement of unit IMPORTANT! ICETECH machines are intended to operate at room temperature between 5°C and 43°C and with water temperature ranging between 5°C and 35°C. You may encounter evaporator/gearbox malfunctions should the machine run at temperatures below the recommended minimum. When running above maximum recommended temperatures you can expect shorter compressor life and decreased production. -
Page 18: Connecting Unit To Water Source (Water-Cooler Units)
ICE TECH SS / SP Technical Service Manual c) CHLORINATED WATER: Chlorine taste can be avoided by installing a carbon filter (NOTE: You may encounter water with all aforementioned properties.) d) PURIFIED WATER: A 10% reduction in overall production may occur. 4.3. -
Page 19: Operation
ICE TECH SS / SP Technical Service Manual 5. OPERATION 5.1. Preliminary check a) Is machine levelled? b) Are voltage and frequency of mains supply the same as indicated on rating plate? c) Is drainage system working properly? d) Is air circulation and room temperature adequate? (Air-cooled models) AMBIENT TEMPERATURE WATER TEMPERATURE MAXIMUM... -
Page 20: Adjustments
ICE TECH SS / SP Technical Service Manual 8) At the cycle’s end, there should be frost formed on the compressor inlet tube except for the last 50 mm. IMPORTANT! Advise the final user on maintenance procedures which are not included in warranty, as well as those breakdowns caused by neglect of proper maintenance procedures. -
Page 21: Maintenance And Cleaning Instructions
ICE TECH SS / SP Technical Service Manual gearbox malfunction. Pressure values higher than 16 Kg/cm2 may shorten compressor life and diminish ice production. Pressure can be regulated by rotating screw on Pressure Control Valve (clockwise to increase pressure). One full turn is aquivalent to about 1.5 Bar. Safety pressostat This safety device trips when pressure is too high. -
Page 22: Maintenance And Cleaning Procedures
ICE TECH SS / SP Technical Service Manual MAINTENANCE TABLE: PROCEDURE MONTHLY QUARTERLY HALF YEARLY BIENNIAL DURATION YEARLY Air condenser 30 minutes cleaning Water condenser 90 minutes cleaning Inyectors cleaning 30 minutes Fabrication head 30 minutes filter cleaning Water circuit 45 minutes cleaning Sanitary cleaning... - Page 23 ICE TECH SS / SP Technical Service Manual 4) Prepare a solution of 50% phosphoric acid in distilled water. 5) Distribute solution through condenser. (Solution is more effective at 35°-40°C). WARNING! DO NOT USE HYDROCHLORIC ACID Air Condenser 1) Disconnect machine. 2) Close water faucet.
- Page 24 ICE TECH SS / SP Technical Service Manual 16) Allow machine to make ice for at least 15 minutes. WARNING:** Discard ice produced during cleaning procedure. 17) Disconnect unit, place cover and check for water leaks. 18) Change joint in water plug if necessary. 19) Replace filters if necessary.
-
Page 25: Special Advise Concerning R-404 Refrigerant
ICE TECH SS / SP Technical Service Manual These round wire gasket filters placed on either end of the water hose to mains, often become blocked in the first few days of use, especially when the plumbing installation is new. Clean them under a jet of water. -
Page 26: Troubleshooting
ICE TECH SS / SP Technical Service Manual 9. TROUBLESHOOTING PROBLEM POSSIBLE CAUSES SOLUTION 1) None of the electrics work. A) The machine is not plugged in. A) Plug the machine. B) The line fuse has blown. B) Replace fuse. C) The current line is wrongly connected C) Check connections. - Page 27 ICE TECH SS / SP Technical Service Manual PROBLEM POSSIBLE CAUSES SOLUTION B) Low water pressure. B) Increase water pressure if possible. (This can often be done by removing flowmeter on faucet). C) Faulty fan or pressostat. C) Check fan and re-adjust pressostat or replace.
- Page 28 ICE TECH SS / SP Technical Service Manual 10) Ice cubes are empty, rough edges A) Insufficient water in water pan; A) Correct a major water leak. and very white. unprimed pump. B) Obstructed spray nozzles. B) Clean. C) Curtain does not close fully. C) Adjust the curtain, clean scale (lime) on curtain metal axis.