VSS 15 is allowed. Please read this instructions before you switch on the VSS 15 for the first time, to get in touch with particular features of your new product. If you have questions about this product please contact the K.M.E. support.
With a powerful bass base and very compact dimensions as well as the lightweight of 26 kg the VSS 15 is also the core and control center within the self-powered PA-systems SD 3, SD 4 and SD 5.
5x20 mm), Attention: use only the correct mains voltage 230 V AC (conforming to standard IEC 60320-C14). 3. Power switch, Attention: please turn down all volume controls before switching on the VSS 15 to avoid an undesirable sound reproduction. Connections 4.
- there is a malfunction, you must power cycle the VSS 15 3. The LCD display is used as operation mode display of the VSS 15. The arrows in the LCD display show the directions to navigate through the submenus (see navigation structure). All software parameters must be set on the unit itself.
General view about presets Currently the VSS 15 includes eight factory presets and four useful adjusted user presets. When switching on for the first time preset 1 “VERSIO SD 3” is loaded (a factory preset). You can load factory presets and change it can be made you will find it on page 16 in this manual.
Page 7
2x VSS 15 + 2x VB 15 + 2x VL 12: 2x VSS 15 + 2x VL 8 + two independently out A = each with a top unit / out B = each adjustable analogue XLR-inputs (full-range) with a bass, analogue or digital audio signal as well as two speaker outputs (Speakon NL 4): respectively to input A ;...
Page 8
1x VSS 15 + 2x VL 8 2x VSS 15 + 2x VL 12 you can set-up your audio inputs & you can set-up your audio inputs & speaker outputs speaker outputs...
Page 9
Bass management system for smaller surround systems (5.1). The VSS 15 for the center channel and LFE-channel (low frequency enhancement) is used with this preset. You can connect an additional bass VB 15 on the speaker output B. The VSS 15 for the L/LS and R/RS are used with the presets no. 9.
“audio-channel” of the digital signal on the input of VSS 15, e.g. for the digital controlling of SD 4 and SD 5 (for the left and right side). Password (see page 18)
• er Presets [appears only from preset no. 9 to 12] Names Pres Name [enter preset name, max. 12 digits] Out A Name [enter name of output A, max. 6 digits Out B Name [enter name of output A, max. 6 digits] Bass uting [routing of the input channels]...
Page 15
Out A (see adjustable parameter bass) Out B (see adjustable parameter bass) Level Control Mode [adjustment resp. co ntrol of output level] independent elative, B inde pendent relative In level control mode you define the pre-settings (dependence) of the single potentiometers (volu e m controls) in relation to the outpu t level of the different channels (Bass / Out A / Out B).
(e.g. select SD 5)! After power on the VSS 15 for the very first time the left graphic appears on the LCD display. You have to press the marked arrow key of the navigation pad two times to select preset 3 „VERSIO SD5“...
witching input of channel A between analog / digital / digital X you want to control your PA system with a digital signal you have to switch the input of channel A to „digital“resp. “digital X” (see page 13). In the programmed initial state all inputs are switched to „analogue“.
VSS 15 with or without a password. To lock the VSS 15 with a password (max. 8 dig its) you have to enter it first. This password can be changed every time. Note! Keep in mind resp. note down the entered password because if you want to „unlock“...
(if entered before) you can press the OK button for two times and the VSS 15 is playing in the current adjustment of the volume controls or you press the OK button only once and turn the volume control(s) to...
VSS 15 Speaker: Components 15“ Neody mium Frequency range 40 Hz – 160 Hz (fx), depending on preset SPL nominal 101 dB SPL maximal 128 dB Electronic: Amplifiers three full digital amplifiers with high efficiency, about 90 % Power output RMS...
Schemes of connection VERSIO SD 3 (use preset no . 1) speaker speaker output output (top unit) (top unit) channel A channel B audio input audio input channel A channel B scheme of the power-output connection of SD 3: from speaker outputs “Out A and Out B” into the top units VERSIO SD 4 (use preset no.
Page 23
1. Set-up power supply.* 2. Plug the XLR-cables (audio signal channel A+B) in the VSS 15. 3. When switching o the system please mind that all volume potentiometers are turned fully anti-clockwise / left stop (to avoid an unwanted sound reproduction) and that all connected components are switched on and muted previously because the VSS 15 could start in the „lock...
Deutsch Entsorgung von Altgeräten 1. Wenn dieses Symbol eines durchgestrichenen Abfalleimers auf einem Produkt angebracht ist, unterliegt dieses Produkt der europäischen Richtlinie 2002/96/EC. Klingenthaler 2. Alle Elektronik-Altgeräte müssen getrennt vom Hausmüll über dafür Musikelektronik GmbH staatlich vorgesehene Stellen entsorgt werden. Auerbacher Straße 268 08248 Klingenthal Germany 3.
Need help?
Do you have a question about the VSS 15 and is the answer not in the manual?
Questions and answers