Summary of Contents for Odin CL-4 Connect
- Page 1 MANUAL ENGLISH ODIN CL-4 Connect Ordercode: D3915 Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands...
-
Page 2: Table Of Contents
ODIN CL-4 Connect Table of contents Warning ....................................2 Safety Instructions ................................. 2 Connection with the mains ............................4 Return Procedure ................................4 Claims ....................................4 Description of the device ..............................5 Overview ..................................5 Frontside ..................................6 Backside ..................................7 Installation ................................... -
Page 3: Warning
ODIN CL-4 Connect Warning Unpacking Instructions Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure that all parts are present, and have been received in good condition. Notify the dealer immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling. - Page 4 Please turn off the power, when changing the power cord or signal cable, or select the input mode • switch. Prevent distortion! Make sure that all components connected to the ODIN have sufficient power • ratings. Otherwise distortion will be generated because the components are operated at their limits.
-
Page 5: Connection With The Mains
ODIN CL-4 Connect Connection with the mains Connect the device to the mains with the power-plug. Always pay attention, that the right color cable is connected to the right place. International EU Cable UK Cable US Cable BROWN YELLOW/COPPER PHASE... -
Page 6: Description Of The Device
You can use it to build a local network, including Wi-Fi connection for communication between your PC and the ODIN Line Array System. There are 4 RJ45 ODIN data output ports for connecting up to 12 ODIN components per each output. -
Page 7: Frontside
ODIN CL-4 Connect Frontside Fig. 02 Antenna LED indicators (1-4) The LEDs will blink when uninterrupted data transfer takes place. LED LAN indicator Once a network has been established, the LED will light up. LED power indicator When the device is connected to the appropriate power supply, the LED will light up. -
Page 8: Backside
ODIN CL-4 Connect Backside Fig. 03 5V DC power connector IN RJ45 RC NET connectors (1-4) Connect your ODIN Line Array System. RJ45 LAN connector IN Connect to a router, in order to establish a network. Ordercode: D3915... -
Page 9: Installation
4 ODIN speakers per phase (16A). 05) In order to enable data signal reception, connect the CL-4 Connect to the first speaker’s RJ45 data input, using a UTP/CAT-5 cable. Connect the first speaker’s data link to the second speaker’s data input. -
Page 10: Set Up And Operation
Do not attempt to operate a 115V specification product on 230V power, or vice versa. Connecting the ODIN Wireless Access Point and Updating You can connect your PC to the CL-4 Connect via the wireless access point, by connecting it to the router. Follow the steps below. - Page 11 There will appear the page shown below. Click on “AP Interface Setting” on the left-hand side of the page. The IP address can be found at the bottom. 06) Once the connection has been established, go to the Odin Editor. The connection indicator should now light in green: 07) Click on the CL-4 UPDATE button to open the window below: 08) It is now possible to update the software.
-
Page 12: Connection Cables
ODIN CL-4 Connect Connection Cables Take care of your cables, always holding them by the connectors and avoiding knots and twists when coiling them: This gives the advantage of increasing their life and reliability. Periodically check your cables. A great number of problems (faulty contacts, ground hum, discharges, etc.) are caused entirely by using unsuitable or faulty cables. -
Page 13: Maintenance
ODIN CL-4 Connect Maintenance The ODIN CL-4 Connect requires almost no maintenance. However, you should keep the unit clean. Disconnect the mains power supply, and then wipe the cover with a damp cloth. Do not immerse in liquid. Do not use alcohol or solvents. -
Page 14: Notes
ODIN CL-4 Connect Notes Ordercode: D3915... - Page 15 ODIN CL-4 Connect Ordercode: D3915...
- Page 16 ©2016 ODIN...