Related Manuals for Weidmuller WAS5 PRO RTD
Summary of Contents for Weidmuller WAS5 PRO RTD
- Page 1 Beipackinformation Operating Instructions Notice d’utilisation Analogsignaltrenner WAVE ANALOG PRO RTD aus der WAVESERIES RT Nr. 406042...
- Page 2 Analogue Signal Isolators WAVESERIES WAVE ANALOGUE PRO RTD MODEL Order Number Screw terminal connection WAS5 PRO RTD 8560700000 Tension clamp connection WAZ5 PRO RTD 8560710000 Please read these instructions before using the product and retain for future information.
- Page 3 General instructions Warning! The analogue signal isolators of the WAVE series ANALOGUE PRO may only be installed by qualified personnel. Be sure not to connect the unit to power supply before appropriate installation. Do not select ranges during operation, because live parts are exposed during this process.
- Page 4 Configuration 3.1 Equipment A screwdriver with a width of 2.5 mm is required to adjust the unit and to connect the wires to the terminals. 3.2 Opening the unit Disconnect the plugs. Disengage the top part of the housing by carefully pressing the latches on both sides (1).
- Page 5 Selecting the inputs Input PT100 2-wire PT100 3-wire PT100 4-wire 2-wire NI100 2-wire NI100 3-wire NI100 4-wire Potentiometer Selecting the minimum input value Poti 0 Ω 0º C 10 Ω –10º C 20 Ω –20º C 25 Ω –25º C 30 Ω...
- Page 6 Poti 100 Ω –100º C 150 Ω –150 °C 200 Ω –200 °C Special range Activating the manual fine adjustment manual calibration 1 = on 0 = off...
- Page 7 Selecting the measuring range Poti 20 Ω 25 Ω 30 Ω 35 Ω 40 Ω 45 Ω 50 Ω 100K 55 Ω 110K 60 Ω 120K 62,5 Ω 125K 62,5% 65 Ω 130K 70 Ω 140K 75 Ω 150K 80 Ω 160K 85 Ω...
- Page 8 Poti 275 Ω 550K – 300 Ω 600K – 325 Ω 650 K – 350 Ω 700K – 375 Ω 750K – 400 Ω 800K – 425 Ω 850K – 450 Ω 900K – Selecting the output Output 0…10 V 0…20 mA 4…20 mA 1 = on...
- Page 9 Selecting the step response time Step response slow fast 1 = on 0 = off 3.4 Terminal assignment of the sensors Terminal assignment for 2-, 3-, 4-wires and potentiometers. 4-wires 3-wires 2-wires Potentiometer Sensor + Sensor - Sensor - Sensor -...
-
Page 10: Power Supply
2 Ei n gang + £ 500 mV / £ 5 mA 3 Input RTD – We dm ü l le r WAS5 PRO RTD 3 Ei n gang + > 500 mV 4 Input Sensor + 4 Ei n gang -... - Page 11 Dimensions 92,4 Cross-connections for power supply 24 Vdc...
- Page 12 Accessories (cross-connection) Designation Cat. No. ZQV 2,5 N/2 yellow 169380 ZQV 2,5 N/2 red 171790 ZQV 2,5 N/2 blue 171799 ZQV 2,5 N/2 black 171808 Connection markers Designation Cat. No. WS 10/5 Multicard for plotter marking 163501 WS 10/5 Neutral 106086 Notes on CE marking The WAS5/WAZ5 RTD analog signal isolators are marked CE in accordan-...
- Page 13 Weidmüller Interface GmbH & Co. Postfach 30 30 D-32720 Detmold Tel. (0 52 31) 14-0 Fax (0 52 31) 14-20 83...