Related Manuals for Solibro SL2
Summary of Contents for Solibro SL2
- Page 1 InstallatIon and operatIon manual Solibro Solar Modules SL2 and SL2-F of the Generation 2.1 and 2.2...
-
Page 2: Table Of Contents
The data sheets and customer information current at the point in time at which the relevant module was manufactured apply for the carrying out of installation, mounting or maintenance work on the solar modules. InstallatIon and oPERatIon ManUal FoR sl2 solaR ModUlEs oF tHE GEnERatIon G2.1 and G2.2... -
Page 3: Introduction
List of approved clamps and mounting systems C ountry-specificregulations,forexample,planningandbuild- ƒ ing laws, operational safety, hazardous goods and environ- Packaging and transport information mental protection. installation instructions for Slide-in ƒ Plant-specificregulationsandrequirements. InstallatIon and oPERatIon ManUal FoR sl2 solaR ModUlEs oF tHE GEnERatIon G2.1 and G2.2... -
Page 4: Planning
Frame (SL2-F only) –0 –0 ± 0.5 ± 0.5 ± 0.5 1190 –1 Fig. 2: Module label SL2 & SL2-F –0 –0 ± 0.5 ± 0.5 InstallatIon and oPERatIon ManUal FoR sl2 solaR ModUlEs oF tHE GEnERatIon G2.1 and G2.2... -
Page 5: Requirements
Ensure that no mechanical stresses (e.g. due to vibrations, ¼ rotations or expansions) are generated on the module. note! Ensurethatthesubstructureisongroundpotential(R≤10Ω). For further notes, see chapter 3 ¼ InstallatIon and oPERatIon ManUal FoR sl2 solaR ModUlEs oF tHE GEnERatIon G2.1 and G2.2... - Page 6 The modules must be po- sitionedstrainlessandfloat-mounted.Thescrewbetween theglass/glassmoduleandtheclampshouldbetightened with the recommended torque of 8 to 10 nm. See applicable documents “List of approved clamps and ¼ mounting systems” InstallatIon and oPERatIon ManUal FoR sl2 solaR ModUlEs oF tHE GEnERatIon G2.1 and G2.2...
- Page 7 All measurements in mm. „ clamp Glass (module top side) ‚ clamp depth Glass (module bottom side) ƒ † Module frame Active surface Frame tape InstallatIon and oPERatIon ManUal FoR sl2 solaR ModUlEs oF tHE GEnERatIon G2.1 and G2.2...
-
Page 8: Mounting Variants
PermissiblecontactareasforSlide-Inandinsertionprofilesystems WhenfixingtheSlide-Inandinsertionprofilesystems,thepermissiblecontactareasmustbeobserved.Self-cleaningoftheframed modulesisensurediftheyareinclinedatanangleof≥25°. Inthecaseofinsertionprofilesystems,themodule’sowndeadweightholdsitinposition.Itisvitalthatyoutakeintoaccountthe dynamic wind loading here, to ensure that the modules cannot not slide out or slip. clamping area Substructure InstallatIon and oPERatIon ManUal FoR sl2 solaR ModUlEs oF tHE GEnERatIon G2.1 and G2.2... - Page 9 2,400 clamping area Substructure The listed mounting variants are valid for point mounting and linear mounting. * TestLoad=γ x Design Load γ ≥1.5(observeregionalrequirements) InstallatIon and oPERatIon ManUal FoR sl2 solaR ModUlEs oF tHE GEnERatIon G2.1 and G2.2...
-
Page 10: Electrical Layout
You can find more information about functional grounding in chapter 5.1. InstallatIon and oPERatIon ManUal FoR sl2 solaR ModUlEs oF tHE GEnERatIon G2.1 and G2.2... -
Page 11: Installation
Follow the packaging instructions Leave the modules in the original packaging ƒ right up until installation Store the modules securely in dry rooms. The ƒ packaging is not weatherproof! InstallatIon and oPERatIon ManUal FoR sl2 solaR ModUlEs oF tHE GEnERatIon G2.1 and G2.2... - Page 12 Do not drop the modules. ¼ never stand on the modules. ¼ Do not apply mechanical stress to the modules. ¼ Do not drop objects on the modules. InstallatIon and oPERatIon ManUal FoR sl2 solaR ModUlEs oF tHE GEnERatIon G2.1 and G2.2...
-
Page 13: Preparation For Installation
¼ Do not carry out the installation alone. only install modules and components which ¼ are free from damage. ¼ Do not add any holes. InstallatIon and oPERatIon ManUal FoR sl2 solaR ModUlEs oF tHE GEnERatIon G2.1 and G2.2... -
Page 14: Module Installation
Please note the requirements on the clamping system out- lined in chapter 2. Tighten the clamps for framed modules with a torque of 18 nm. ¼ InstallatIon and oPERatIon ManUal FoR sl2 solaR ModUlEs oF tHE GEnERatIon G2.1 and G2.2... -
Page 15: Electrical Connection
Work on the inverter and on the cables may only be carried ¼ outbyaqualifiedelectrician. danger! danger due to electric shock! ƒ insulate exposed cable ends. ¼ ¼ only connect cables with plugs. InstallatIon and oPERatIon ManUal FoR sl2 solaR ModUlEs oF tHE GEnERatIon G2.1 and G2.2... -
Page 16: Safety During Electrical Installation Work
¼ connectors can only be disconnected using an RH-01 tool from Renhe SWITCH click InstallatIon and oPERatIon ManUal FoR sl2 solaR ModUlEs oF tHE GEnERatIon G2.1 and G2.2... -
Page 17: After The Installation
Ensure that the substructure is on ground Protect the cabling from dirt and wet. ¼ ¼ potential:(Groundresistance≤10Ω) InstallatIon and oPERatIon ManUal FoR sl2 solaR ModUlEs oF tHE GEnERatIon G2.1 and G2.2... -
Page 18: Grounding
SL2-F (framed) ground-mounted systems/ max. 2 A max. 2 A utility rooftop systems max. 300 mA max. 1 A *The valid regulations for personal protection remain unaffected. InstallatIon and oPERatIon ManUal FoR sl2 solaR ModUlEs oF tHE GEnERatIon G2.1 and G2.2... -
Page 19: Potential Equalization Of Frame
Stainless self-tapping screw ‚ Stainless washer (cable lug) ƒ Stainless serrated lock washer „ Module frame Grounding point InstallatIon and oPERatIon ManUal FoR sl2 solaR ModUlEs oF tHE GEnERatIon G2.1 and G2.2... -
Page 20: Cleaning And Maintenance
10 °c and 30 °c, e.g. in the early morning or late evening. Don’tcleandamagedmodules.Thiscancauseanelectricshock. Remove soiling from the substructure (leaves, ¼ bird nests etc.). InstallatIon and oPERatIon ManUal FoR sl2 solaR ModUlEs oF tHE GEnERatIon G2.1 and G2.2... -
Page 21: Additional Information
14 AWG (min. 2.5 mm²). I nordertofulfiltherequirementsinaccordancewiththeCa- ƒ nadianStandardULC/ORD-C1703-1,theinstallationmustbe carried out in accordance with cSA-c22.1, Safety standard for electrical installations, canadian Electrical code, Part 1. InstallatIon and oPERatIon ManUal FoR sl2 solaR ModUlEs oF tHE GEnERatIon G2.1 and G2.2... - Page 22 SOLIBRO GMBH OT Thalheim, Sonnenallee 32–36 EMAIL service@solibro-solar.com www.solibro-solar.com 06766 Bitterfeld-Wolfen, Germany...
Need help?
Do you have a question about the SL2 and is the answer not in the manual?
Questions and answers