Table of Contents
Advertisement
Programme Options
Use the directional buttons to highlight a programme and press
OK button to display Event Options menu. The following
options are available.
Select Channel: Using this option, you can switch to the
selected channel.
Record / Delete Rec. Timer: Select the Record option
and press the OK button. If the programme is going to be
broadcasted at a future time, it will be added to Timers list to
be recorded. If the selected programme is being broadcasted
at the moment, recording will start immediately.
To cancel an already set recording, highlight that programme
and press the OK button and select the option Delete Rec.
Timer. The recording will be cancelled.
Set Timer on Event / Delete Timer on Event: After you have
selected a programme in the EPG menu, press the OK button.
Select Set Timer on Event option and press the OK button. You
can set a timer for future programmes. To cancel an already set
timer, highlight that programme and press the OK button. Then
select Delete Timer on Event option. The timer will be cancelled.
Notes: You cannot switch to any other channel while there is an active
recording or timer on the current channel.
It is not possible to set timer or record timer for two or more individual
events at the same time interval.
Teletext Services
Press the Text button to enter. Press again to activate mix
mode, which allows you to see the teletext page and the TV
broadcast at the same time. Press once more to exit. If available,
sections in the teletext pages will become colour-coded and
can be selected by pressing the coloured buttons. Follow the
instructions displayed on the screen.
Digital Teletext
Press the Text button to view digital teletext information.
Operate it with the coloured buttons, cursor buttons and the
OK button. The operation method may differ depending on the
contents of the digital teletext. Follow the instructions displayed
on the digital teletext screen. When the Text button is pressed
again, the TV returns to television broadcast.
Software Upgrade
Your TV is capable of finding and updating the firmware
automatically via the broadcast signal or via Internet.
Software upgrade search via user interface
On the main menu select Settings and then More. Navigate
to Software upgrade and press the OK button. In Upgrade
options menu select Scan for upgrade and press OK button
to check for a new software upgrade.
If a new upgrade is found, it starts to download the
upgrade. After the download is completed confirm the
question asking about rebooting the TV by pressing the
OK to continue with the reboot operation.
3 AM search and upgrade mode
Your TV will search for new upgrades at 3:00 o'clock if
Automatic scanning option in the Upgrade options menu is
set to Enabled and if the TV is connected to an aerial signal
or to Internet. If a new software is found and downloaded
successfully, it will be installed at the next power on.
Note: Do not unplug the power cord while led is blinking during the
reboot process. If the TV fails to come on after the upgrade, unplug,
wait for two minutes then plug it back in.
Troubleshooting & Tips
Tv will not turn on
Make sure the power cord is plugged in securely to wall outlet.
Check if batteries are exhausted. Press the Power button on
the TV.
Poor picture
• Check if you have selected the correct TV system.
• Low signal level can cause picture distortion. Please check
antenna access.
• Check if you have entered the correct channel frequency if
you have done manual tuning.
• The picture quality may degrade when two devices are
connected to the TV at the same time. In such a case,
disconnect one of the devices.
No picture
• This means your TV is not receiving any transmission. Make
sure the correct source has been selected.
• Is the antenna connected properly?
• Is the antenna cable damaged?
• Are suitable plugs used to connect the antenna?
• If you are in doubt, consult your dealer.
No sound
• Check if the TV is muted. Press the Mute button or increase
the volume to check.
• Sound may be coming from only one speaker. Check the
balance settings from Sound menu.
Remote control - no operation
• The batteries may be exhausted. Replace the batteries.
Input sources - can not be selected
• If you cannot select an input source, it is possible that no
device is connected. If not;
• Check the AV cables and connections if you have tried to
connect a device.
• Check the AV cables and connections if you are trying to switch
to the input source dedicated to the connected device.
Recording unavailable
To record a programme, you should first connect a USB disk
to your TV while the TV is switched off. You should then switch
on the TV to enable recording feature. If you cannot record,
try switching off the TV and then re-inserting the USB device.
USB is too slow
If a "USB disk writing speed too slow to record" message is
displayed on the screen while starting a recording, try restarting
the recording. If you still get the same error, it is possible that
your USB disk does not meet the speed requirements. Try
connecting another USB disk.
English - 15 -
Advertisement
Table of Contents
Troubleshooting
