Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Elite Manuals
  4. Massager
  5. Robo-Pad
  6. Assembly instructions manual

Elite Robo-Pad Assembly Instructions Manual

Hide thumbs Also See for Robo-Pad:

Advertisement

Quick Links

Download this manual See also: Operating Manual
Elite Robo-Pad Unboxing and Assembly Instructions
For questions, clarifications or assistance call 1-800-592-0548

Section 1. Chair unboxing

Tools required: knife, scissors or razor knife.
Your chair will arrive in two separate boxes. The larger box contains the chair as well as two smaller accessories
.
boxes contained within. The separate smaller box contains the arms of the chair
This is how your chair boxes should look upon delivery. If there is any damage, please call Elite
Massage Chairs.
Step 1) Cut plastic bands wrapped around box.

Advertisement

loading
Need help?

Need help?

Do you have a question about the Robo-Pad and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Elite Robo-Pad

Summary of Contents for Elite Robo-Pad

  • Page 1: Section 1. Chair Unboxing

    Your chair will arrive in two separate boxes. The larger box contains the chair as well as two smaller accessories boxes contained within. The separate smaller box contains the arms of the chair This is how your chair boxes should look upon delivery. If there is any damage, please call Elite Massage Chairs.
  • Page 2 Step 2) Lift lid off box and set aside – Lift from the handles on each end of the box. There is no need to cut the tape on the lid to remove it. Step 3) Remove all packaging from around chair See additional photos of chair packaging to be removed on following page...
  • Page 3 Step 4) Remove accessories boxes and plastic off of chair The chair is designed to be moved using the wheels on the rear of the chair. The easiest method for removing the chair from the lower box, is to simply roll it out. In order to do so, the chair back must be in the upright position.
  • Page 4 Step 6) Unpakage the remote. The remote is placed in the footrest when shipping, remove all packaging from the remote, or at least enough packaging to be able to access the front of the remote and the buttons Step 7) Raise the backrest. Do not press the power switch on the remote. Press and hold only the following button until the chair is in the full upright position:...
  • Page 5 Step 8) Cut tape on box edge. Cut tape on the front edge of the box. Lay the box edge flat in order to roll the chair out. As the front edge of the box is held upright with tape only, the box may be easily be used again if needed by re-applying packaging tape where cut.
  • Page 6 Step 10. (Alternate method for removal) If you are unable to plug in the chair, or if utilizing the wheels to roll the chair out of the lower box is impractical for any reason, you may lft the chair out of the box by the metal frame on each side.

  • Page 7: Section 2: Chair Assembly

    Section 2: Chair assembly Tools required: Philips screwdriver, #5 Allen wrench / Hex key (included with chair) Your chair arms will be located in a separate box from the chair and require installation. There are two accessories boxes (removed in section 1) located inside the large chair box which contain the controller stand and upper air bag / speaker assembly’s which also require installation.
  • Page 8 Locate the corresponding wires on the interior of the chair arm. Please note that there is one wire and one air pipe from the arm. One wire from the chair frame is not used on the right side only. Connect the white plug wire and air pipe Step 1B: Mount right arm to chair frame.
  • Page 9 Step 1C: Install the screws for the arm. Install the screws removed in step 1B. The silver hex key provided will be used to tighten the screws Rear screw location: Front screw location:...
  • Page 10 Step 2: Install left arm. Repeat the procedure for step one. Note that there are two additional plugs for the left arm, three total, as shown below. Connect the plugs and air pipe accordingly. The remainder of the procedure is the same as the right arm Step 3: Install right and left upper air bag / speaker assembly.
  • Page 11 Remove the plastic covering panel from the rear of the speaker assembly. Remove the one screw from the edge of the panel. You may have to gently pry the panel off of the assembly using a small flat head screwdriver. Step 3B: Mount the speaker / air bag assembly Once the panel is removed, note the location of the wire / air pipe hole in the assmebly.
  • Page 12 Locate the mounting location for the speaker / air bag assembly on the chair, remove the screws from this location Mount the air bag / speaker assembly by inserting the mounting posts into the large holes on the side of the chair.
  • Page 13 Connect the air pipe and wire. Insert screws previously removed from side of chair through holes shown below. Step 3C: Replace covering panel: Replace covering panel, install with screw previously removed. Step 3D: Install opposite side speaker / air bag assembly. The process is the same for each side. Step 4: Install remote stand.
  • Page 14 Install the controller stand onto the controller stand mount on the right arm, making sure to line up the indent on the bottom of each piece. Insert screws into each side of the controller stand For questions, clarifications or assistance call 1-800-592-0548...