Advertisement
Quick Links
Easy RGB(Y) Remote controller User Manual
1. Product introduction
Easy RGB(Y) remote controller is a wireless color control system that
consists a sender and a receiver or several receivers, as shown in Figure 1, 2:
By selecting switch status, you can set the system as RGB 3-channel
output, or RGBY 4-channel output. Using
you can get whatever color you want; you can choose any color from RGB(Y)
to adjust so as to
kinds of color changing modes, you can easily switch color changing modes
and adjust speed and brightness. "Function Pause" enables RGBY LED to stay
at your favorite color under the situation of color changing modes, which
operation is simple but functional.
Three working frequencies are available: 434MHZ，868MHZ or
915MHZ,which are suitable for
world .All products completely comply with European CE regulations and
American FCC regulations.
mix more than 100 million kinds of colors. With built-in 10
Europe, Americas and elsewhere in the
Easy RGB(Y) remote controller,
1
Advertisement
Related Manuals for Ledco Easy RGB(Y)
Summary of Contents for Ledco Easy RGB(Y)
- Page 1 Easy RGB(Y) Remote controller User Manual 1. Product introduction Easy RGB(Y) remote controller is a wireless color control system that consists a sender and a receiver or several receivers, as shown in Figure 1, 2: By selecting switch status, you can set the system as RGB 3-channel output, or RGBY 4-channel output.
- Page 2 Fig.1 Fig.2...
- Page 3 2. Performance parameters 2.1 Sender: (model:SR-2806) Working temepature:4.5V(3×1.5V 7 AAA battery) Working current：＜22mA Dormancy current：＜20μA Working frequency：434MHZ/868MHZ/915MHZ (optional) Transmit power ：≥5dBm 2.2 Receiver (model：SR-1003RC/SR-1012RC/SR-1022RC model) Input Voltage：12-36VDC Output Voltage：12-36VDC Input Current：4CH×3A max (SR-1003RC) 4CH×350mA (SR-1012RC) 4CH×700mA (SR-1022RC) Output power：4CH×(36-108W) max (SR-1003RC) 4CH×(4.2-12.6W) (SR-1012RC) 4CH×8.4-25.2W)
- Page 4 “G” button and indicator。 “B” button and indicator。 “Y” button and indicator。 Working status indicator, the sender is in dormant status when the indicator is off. The sender is under working when the indicator is flashing rapidly. If the indicator continues flashing at the frequency of 1 second, it indicates that the sender batteries low and needs to replace new batteries.
- Page 5 Touch wheel for selecting R/G/B colors. 3.2 Receiver (Model:-1003RC/SR-1012RC/SR-1022RC) J1---power input socket J2---RGB(Y) output socket J3—RGB/RGBY output switch, closed circuit is RGB 3 channel output, open circuit is RGBY 4 channel output. Receiver ID code learning Button Receiver ID code learning indicator and for receiving message 4.
- Page 6 4.2 Receiver learning ID Initial using easy RGB(Y) remote controller must learn the ID of the receiver, the purpose of learning ID code is to make a certain receiver which can correspond the sender. The method of Receiver learning ID is as follows: press the ID learning button on the sender, the ID learning indicator is on, then press...
- Page 7 pressing function button that we define it as MASTER receiver. The purpose of learning these two kinds of receivers is to ensure the receivers and color changing synchronously to avoid the color changing out of order. This point will be noted later. 4.3 Delete ID and ID re-learning If you need to delete the ID learned in the receiver, press ID learning button...
- Page 8 need press number 1 to 6 button first, then touch the color wheel 4.5 Change color by R, G, B, Y button In addition to change the color by touching color wheel , but you can also change the color through R,G, B, Y buttons .For example, you choose a color by touching color wheel and still want add a bit more brightness to red color, just...
- Page 9 By pressing of R ,G, B, Y button ,you can turn on/off the corresponding color. For example under a certain mode, turn off the red color, press for 2 seconds, then the red color will be turn off. If you want to turn on red again, press R for another 2 seconds, the red will be on again.The same operation for other colors.
- Page 10 number button , and choose receiver number, then press button again. For first press of button , receiver will change according to mode 1, one more time press of button , the receiver will be paused, it will stay at one color under mode 1 condition. Press button again, the color will change according to mode 2, press button one more time , it will be paused at one color under mode 2.
- Page 11 maximum is 100%. 4.8 Changing speed adjustment Under color changing mode, you can slow down the changing speed by pressing button , or speed up changing speed by pressing button , 16 speed levels in total are available. The maximum changing cycle is 4 seconds;...
- Page 12 forever . For example, 10 receivers are learned to be ID 1. , these 10 receivers will change according to one mode, in order to avoid chaos of working units after a long time, one of the receivers is needed to be set as Master ,the Master will launch synchronized signal when color is changing, thus ensure this group of receivers are in good order no matter how long the color is changing 5.5 Color changes of multiple-different ID receivers in the same mode...
- Page 13 Press button for 2 seconds to switch between Synchronous color move and Asynchronous color changing when multiple different receivers are in the same mode. Synchronous color changing means the starting point and ending point are at the same time, Asynchronous color changing means there is certain time delay of the starting point and ending point, the later receiver start or ending point is always later than the previous receiver.
- Page 14 press button or button to adjust its brightness. 5.5.2 Pressing number button can turn on/Off the corresponding single receiver, E.g. If you need to turn off receiver 1, press button more than 2 seconds, if you need turn it on again, please press button again for more than 2 seconds.
- Page 15 The sender 1. Receiver isn’t 1. To learn the receiver by cannot control learned to the the sender. the receiver sender。 2. When receiver is learned 2. The receiver isn’t to the sender, press learned to the number button first，then sender correctly。...
- Page 16 7.2 Don’t fall the sender from a high place or don’t squeeze it. 7.3 Please replace new batteries if there is a warning indicator of insufficient power, otherwise it would cause damage to the sender.. 7.4 Receiver is non-waterproof, not for outdoor use.
Need help?
Do you have a question about the Easy RGB(Y) and is the answer not in the manual?
Questions and answers