HUSTLER MDV Operator's Manual page 27

will be denied when engine damage results from such
use.
Ambient Temperature
Above 60°F (15°C)
Above 10°F (–12°C)
Below -10°F (–23°C)
5. Depress the brake pedal and rotate the ignition switch
key fully clockwise to engage the starting motor.
Release the key when the engine starts.
IMPORTANT: The engine starter should not be oper-
ated for periods longer than 10 seconds at a time. An
interval of at least two minutes should be allowed
between such cranking periods to protect the starter
from overheating and burn-out.
NOTE: All accessories can be used when the ignition
switch key is in the PRE-HEAT/RUN" position and the
engine is not running. Do not leave the key in this posi-
tion as the battery will be depleted. Rotate the key back
to the "OFF" position when done.
6. As soon as the engine begins to run, check to make
certain the oil pressure light and the alternator warn-
ing light are off. If not, stop engine immediately and
check for the cause.
Engine Warm Up
During engine warm up:
• Make sure the park brake is engaged.
• Make sure the gear select lever is in the
"NEUTRAL" position.
Allow the engine to idle a few minutes before applying a
load. This allows engine oil to circulate properly throughout
the engine.
IMPORTANT: This may prevent engine problems such as
seizure, parts breakage, and pre-mature wear.
Stopping the Engine
Use the following procedure to shut the engine off.
1. Throttle the engine back to low idle.
2. Place the gear select lever in the "NEUTRAL" position.
3. Engage the park brake lever to set the park brake.
4. Allow the engine to slow to low idle and then rotate the
ignition key counter-clockwise to the "OFF" position.
Remove the key from the switch before leaving the
vehicle.
Driving the Vehicle
1. Perform the Pre-Operation Check as outlined previ-
ously.
606653
Preheating time
Ordinary heat type
No need
One cycle
Two cycles
3-5
2. Adjust and fasten the seat belt.
3. Adjust the steering wheel for operator comfort, if nec-
essary.
4. Start the engine and allow it to warm up per the Start-
ing the Engine and Engine Warm Up sections.
5. Turn the head lights on, if necessary.
6. Push down on the brake pedal to engage the brakes.
7. Disengage the park brake.
8. Release the brake pedal and apply pressure to the
speed control pedal.
When driving in reverse remember to:
• Turn around, look down, and behind you before pro-
ceeding.
• Depress the speed control pedal gradually.
• To stop, when traveling in reverse, remove your foot
from the speed control pedal and gradually apply pres-
sure to the brake pedal. Do not engage the brake pedal
suddenly or with too much pressure.
IMPORTANT: The vehicle does not have engine braking.
When the throttle pedal is released and the engine speed
slows to idle, the vehicle's transmission disengages. Use the
brakes to control the vehicle's speed.
Steering the Vehicle
To allow for easier steering and control the Hustler
is equipped with power steering.
The power steering is active when the key is in the "PRE-
HEAT/RUN" position. The steering will function like a vehicle
without power steering when the ignition is turned off.
The power steering system makes steering control easier.
Exercise caution when traveling at high speeds.
When the vehicle is stationary avoid turning the steering
wheels as this will shorten tire life.
Stopping the Vehicle
To stop the vehicle:
1. Release pressure from the speed control pedal.
2. Apply gradual pressure to the brake pedal.
3. After the vehicle has come to a complete stop, move
the gear select lever to the "NEUTRAL" position, and
engage the park brake.
Parking the Vehicle
1. Stop the vehicle on a level surface. Avoid parking on a
slope. If parking on a slope is unavoidable, block or
chock the vehicle's wheels to prevent rolling.
2. Set the gear select lever in the "NEUTRAL" position.
3. Engage the park brake.
4. Lower attachment to the ground (if equipped).
5. Shut the engine off.
6. Remove the key from the ignition switch.
MDV™
®
REV A