DeWalt DS620 Instructions page 2

Prevention of False Alarms
The majority of alarms that occur are false. These situations
happen every day due to user error, incorrect installation or
improper maintenance of the system. False alarms will limit
the responsiveness to the system and become a general
inconvenience. As the number of false alarms increases,
authorities have become less apt to respond to alarm systems
due to this problem. Many of these situations can be avoided by
following some very simple practices.
• Ensure all users are properly trained on the operation of the system.
• Always Disarm the DS600 Mobilelock™ before entering
protected area.
• Lock all protected doors, windows or any other asset sensor
is attached to.
• Check that premises are cleared and assets secured before
Arming the system.
• Know how to cancel an alarm or turn off the system before activating.
• Test the system on a monthly basis to ensure proper functioning
• Check cellular signal, power supply, and that sensors are
secured on a daily basis.
Recommended Locations
Recommended for use in pull behind trailers, offices, homes
under construction, and climate controlled storage. Use for
monitoring a door, window or gap of up to 3/8" (9.5mm).
Additional normally closed sensor (N.C.) may be wired into the
terminal block on the board.
Installing & Changing Battery
The DS620 Door/Window Contact Sensor requires a non-
rechargeable CR-123 3.0 Volt Lithium battery.
CAUTION: POTENTIAL EQUIPMENT MALFUNCTION OR
FAILURE. Do not touch the electronic components inside the
device, except the reset button and battery.
TO INSTALL BATTERY
1. Open the housing of the sensor by squeezing both short
ends together until the front cover releases.
2. Install the battery using the polarity (+ and -) markings on
the battery and equipment. Do not use excessive force. If
the battery does not fit, ensure that it matches the polarity
markings (Fig. 1).
3. Press the Reset Button (C) on the device. After resetting the
sensor (see Device Registration), make sure Tamper Spring is
in place and replace cover.
TO CHANGE THE BATTERY
CAUTION: Never use a damaged or worn out battery.
1. Carefully remove the old, discharged battery. Dispose of the
battery according to local regulations.
2. Install new battery using the polarity (+ and -) markings on
the battery and equipment. Do not use excessive force. If
the battery does not fit, ensure that it matches the polarity
markings (Fig. 1).
3. Press the Reset Button (C) on the device. After resetting the
sensor, replace the cover.
Device Registration
1. To activate this sensor, it must first be assigned to your DS600
Mobilelock™ Device. Instructions for assigning your sensor
can be found within your online Mobilelock™ account.
NOTE: This sensor can be paired to only one DS600 Mobilelock™
device at a time.
1. Log into your online Mobilelock™ account.
2. Select the Mobilelock™ device you wish to pair this sensor to
and go to the Configure Units page.
3. Click the link titled "Manage Bluetooth
4. Click to "Enable" Bluetooth
5. After the Mobilelock™ device's Bluetooth
"Enabled", click "Add Sensor". After the battery is installed
in the sensor hold it close to the DS600 and click "Scan for
available sensors".
6. When the website shows the sensor click on it to confirm
your selection.
7. Then configure the sensor: Give it a name (ei: "Downstairs
Door").
8. Select any optional alerts desired and click "Save and Close".
9. Make sure the sensor is selected as "Enabled".
10. After registration, Arm the DS600 Mobilelock™ and test the
sensor.
FUNCTIONING TEST
Wait 9 minutes since last door open or door closed alarm
was detected then open and close the door again. Check to
see that the alarm was detected in the Event History for the
DS600 Mobilelock™ on the Configure Units page and also that
notification of the alarm was received as per the settings on the
Alarm Contacts page. You can re-Arm the DS600 after each
alert to eliminate the 9 minute mask period between alarms.
Mounting
• The DS620 comes with a mounting bracket that can be
installed using two #8 screws (not provided) or the mounting
tape provided.
• Refer to figures 3 and 4 above for placement recommendations
• Be sure that the sensor is secure so it will not be bumped or
otherwise moved.
Full One Year Warranty
The D WALT Mobilelock™ Portable Alarm System is warranted
e
for one year from date of purchase. We will repair, without charge,
any defects due to faulty materials or workmanship. For warranty
repair information, visit www.dewaltmobilelock.com or email us
at info@dewaltmobilelock.com. This warranty does not apply to
accessories or damage caused where repairs have been made
or attempted by others. This warranty gives you specific legal
rights and you may have other rights which vary in certain states
or provinces.
D WALT, GUARANTEED TOUGH, and the yellow and black
e
color scheme are trademarks of the D
used under license. Mobilelock™ is a trademark of Mobilelock
LLC. Manufactured by Mobilelock LLC: 550M Ritchie Hwy #279,
Severna Park, MD 21146.
" in the Sensors section.
®
.
®
is confirmed
®
WALT Industrial Tool Co.
e