7
CRB
- COMBINATION
ROUTER BASE MK
INSTRUCTION MANUAL
Please read these instructions before use.
v.IX
COMBINATION ROUTER BASE
(CRB7)
Thank you for purchasing the MPOWER
Combination Router Base (CRB7) we hope you
enjoy using it.
The CRB7 should give lasting performance if
used in accordance with these instructions.
The following symbols are used throughout
these instructions.
3
SAFETY
Please read and understand the safety points at
the end of these instructions as well as the
power tool instructions before use.
Users must be competent in safe routing
practices before using this product.
PLEASE KEEP THESE INSTRUCTIONS IN A
SAFE PLACE.
INTENDED USE
This accessory is a retro fit, quick change,
multi-functional router base for use with routers
that:
+DV URXWHU EDVH URG GULOOLQJV DFFHSWLQJ WZR
5/16" (7mm) rods.
+DV URXWHU EDVH URG KROH KHLJKW EHWZHHQ
+DV URXWHU EDVH URG KROH FHQWUH VSDFLQJ
between:
The CRB7 Combination Router Base is
intended to:
,QFUHDVH WKH overall versatility of the router.
,PSUove the quality of finish of every routing
pass.
Reduce the possibility of error.
,QFUHDVH VWDELOLty during routing.
,QFUHDVH WKH OHvel of precision achieved.
6ave set up time between tasks.
6ave space on storing hand made jigs.
Denotes risk of personal injury, loss
of life or damage to the tool in case
of non-observance of the
instructions.
Refer to the instruction manual
provided with your power tool.
Min. height 15/64" (6mm)
Max. height 1.19/64" (33mm)
Min. centres 1.11/32" (34mm)
Max. centres 6.7/8" (174 mm).
FEATURES
$GMXVWDEOH 'DGRTrenching with a
Clamp Guide.
$GMXVWDEOH 0RUWLVLQJ IRU PDWHULDO ´
(50mm) to 5/16" (125mm).
$GMXVWDEOH $QWLWLOW VXSSRUW
$GMXVWDEOH False Panel Groove Copier.
2IIVHW %DVHSODWH
6PDOO &LUFOH Router Compass
*Radius 3/4" (19mm) - 8.13/16"(224mm).
/DUJH &LUFOH Router Compass
*Radius 7" (180mm) - 25" (635mm).
*Measured from outside edge of hole and
using a 1/4" (6mm) cutter.
Note: All dimensions shown are based on a T5
router being used with a 1/4" (6.3mm) router
cutter.
ITEMS REQUIRED
Router with a suitable rod size and
centres.
Router cutter.
&ODPSV
[ ´ PP $) RSHQ HQGHG VSDQQHU
´ PP $) RSHQ HQGHG VSDQQHr.
+DQG Tools.
CONTENTS
Page No.
3. Items enclosed & Description of parts
4. Setting Up
Fitting the CRB to your router
Guide rod selection
Loosen the lock nuts
,QLWLDO $OLJQPHQW
5. Safe cutter alignment
Guide rod adjustment
Crank plate adjustment
6. Fitting the router
Setting the fixed rod
7. Fitting the index rule
Lock Bars
The micro adjuster
8. Operation
Adjustable dadoing with clamp guide
Adjustable offset mortising
Material width 2 - 4.7/8"
9. Material width 4.7/8 - 8.5/8"
Anti-tilt support
10. Adjustable false panel groove copier
Offset baseplate
11. Cutting small circles
Pivot pin storage
Min. Radius 3/4" (19mm)
Max. Radius 4.15/16" (125mm)
Max. Radius 8.13/16" (224mm)
12. Cutting large circles
13. CRB7 Accessories
Maintenance
Environmental protection
Guarantee
14. Safety points
15. Other MPOWER products
2
Need help?
Do you have a question about the CRB7 and is the answer not in the manual?
Questions and answers