Page 1
3 7 63 1515 0 For U.S.A. & Canada model Ver. 1 SERVICE MANUAL DVM-1815 MODEL DVD VIDEO AUTO CHANGER L 13942296513 注 意 サービスをおこなう前に、このサービスマニュアルを 必ずお読みください。本機は、火災、感電、けがなど に対する安全性を確保するために、さまざまな配慮を おこなっており、また法的には「電気用品安全法」に もとづき、所定の許可を得て製造されております。 従ってサービスをおこなう際は、これらの安全性が維 持されるよう、このサービスマニュアルに記載されて いる注意事項を必ずお守りください。 ● ● 本機の仕様は性能改良のため、予告なく変更すること For purposes of improvement, specifications and design are subject to change without notice.
DVM-1815 LASER BEAM SAFETY PRECAUTIONS 3 7 63 1515 0 This DVD player uses a pickup that emits a laser beam. Do not look directly at the laser beam coming from the pickup or allow it to strike against your skin.
DVM-1815 IMPORTANT SAFETY PRE- I. Also check areas surrounding repaired locations. 3 7 63 1515 0 CAUTIONS J. Be careful that foreign objects (screws, solder droplets, etc.) do not remain inside the set. Product Safety Notice K. Crimp type wire connector...
Page 6
DVM-1815 Safety Check after Servicing 3 7 63 1515 0 Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts, Chassis or Secondary Conductor and wires have been returned to their original posi- tions. Afterwards, do the following tests and confirm...
DVM-1815 STANDARD NOTES FOR SERVICING 3 7 63 1515 0 Circuit Board Indications How to Remove / Install Flat Pack-IC 1. Removal 1. The output pin of the 3 pin Regulator ICs is indi- cated as shown. With Hot-Air Flat Pack-IC Desoldering Machine:.
Page 8
DVM-1815 With Soldering Iron: (4) Bottom of the flat pack-IC is fixed with glue to the 3 7 63 1515 0 CBA; when removing entire flat pack-IC, first apply (1) Using desoldering braid, remove the solder from all soldering iron to center of the flat pack-IC and heat pins of the flat pack-IC.
Page 9
DVM-1815 Instructions for Handling 2. Installation 3 7 63 1515 0 Semi-conductors (1) Using desoldering braid, remove the solder from the foil of each pin of the flat pack-IC on the CBA Electrostatic breakdown of the semi-conductors may so you can install a replacement flat pack-IC more occur due to a potential difference caused by electro- easily.
DVM-1815 CABINET DISASSEMBLY INSTRUCTIONS 3 7 63 1515 0 1. Disassembly Flowchart REMOVAL REMOVE/*UNHOOK/ This flowchart indicates the disassembly steps to gain LOC. PART Fig. UNLOCK/RELEASE/ Note access to item(s) to be serviced. When reassembling, UNPLUG/DESOLDER follow the steps in reverse order. Bend, route, and [6] Function CBA D4 *2(L-3), CN2201 dress the cables as they were originally.
Page 11
DVM-1815 (1): Identification (location) No. of parts in the figures 3 7 63 1515 0 (2): Name of the part (S-2) (L-1) (3): Figure Number for reference (4): Identification of parts to be removed, unhooked, unlocked, released, unplugged, unclamped, or (L-1) desoldered.
Page 12
DVM-1815 3 7 63 1515 0 Drive Mecha Assembly CN5003 Short the three short lands by soldering CN5002 [9] Sensor CBA CN5005 (S-6) [8] Relay CN5001 (S-5) Fig. D6 (S-7) [10] Rear Panel (S-8) View for A (S-7) (S-8)
DVM-1815 TROUBLESHOOTING 3 7 63 1515 0 FLOW CHART NO.1 The power cannot be turned on. Is the fuse normal? See FLOW CHART No.2 <The fuse blows out.> Is normal state restored when once unplugged Check if there is any leak or shor-circuiting on the power cord is plugged again after several seconds? primary circuit component, and service it if defective.
Page 15
DVM-1815 3 7 63 1515 0 FLOW CHART NO.6 P-ON+9V (EV+9V) is not outputted. Check D1030, C1035, C1048, L1009 and Is 9V voltage supplied to the emitter of Q1002? the periphery circuit, and service it if defective. Check Q1016 and service it if defective.
Page 16
FLOW CHART NO.12 DVM-1815 The fluorescent display tube does not light up. 3 7 63 1515 0 Is 3.3V voltage supplied to Pin(6) and Check the P-ON+3.3V line and service it if defective. Pin(24) of IC2001? Is the voltage of approximately -24V to -28V Check the -FL (-28V) line and service it if defective.
Page 17
DVM-1815 3 7 63 1515 0 FLOW CHART NO.14 No operation is possible from the remote control unit. Operation is possible from the DVD, but no operation is possible from the remote control unit. Check P-ON+5V line and service it if defective.
Page 18
DVM-1815 3 7 63 1515 0 FLOW CHART NO.18 [No Disc] indicated. (When the focus servo is not functioning.) Replace the DVD Main CBA. No improvement can be found. Original DVD Main CBA is poor. Replace the DVD Mecha.
Page 19
DVM-1815 3 7 63 1515 0 Are the video signals outputted to each pin of IC6102? IC6102 4PIN Is 5V voltage supplied to Pin(16) of IC6102? IC6102 15PIN Pb/Cb IC6102 14PIN Pr/Cr Replace IC6102. Check P-ON+5V line and service it if defective.
Page 20
DVM-1815 3 7 63 1515 0 FLOW CHART NO.22 Audio is not outputted. Set the disc on the disc tray, and playback. Replace the DVD Main CBA or DVD Mecha. Are the analog audio signals outputted to each pin...
Page 21
DVM-1815 3 7 63 1515 0 FLOW CHART NO.23 Rotary tray does not function. Is the normal control voltage inputted to pins Check the switches (SW2206 - 2208, 2210 - 2212) (39, 40, 41) of IC3001? For each terminal voltage, and their periphery, and service it if defective.
DVM-1815 3 7 6 3 1 5 1 5 0 BLOCK DIAGRAMS System Control/Servo Block Diagram FOCUS SERVO SIGNAL TRACKING SERVO SIGNAL SLED SERVO SIGNAL SPINDLE SERVO SIGNAL IC3001 +3.3V SWITCH CBA CHANGER CBA (CH MICROPROCESSOR) SW3102 TRAY CLOSE...
Page 23
DVM-1815 3 7 6 3 1 5 1 5 0 Digital Signal Process Block Diagram DATA(VIDEO) SIGNAL DATA(AUDIO) SIGNAL DATA(VIDEO/AUDIO) SIGNAL VIDEO SIGNAL FOCUS SERVO SIGNAL TRACKING SERVO SIGNAL IC102 (SDRAM) IC101 (MICRO CONTROLLER) CN202 SDRAM ADDRESS(0-10) SDRAM ADDRESS(0-10)
Page 24
DVM-1815 3 7 6 3 1 5 1 5 0 Video / Audio Block Diagram DATA(AUDIO) SIGNAL AUDIO SIGNAL VIDEO SIGNAL JK1401 S-VIDEO OUT IC1402 (VIDEO DRIVER) W F 1 W F 2 DRIVER IC6102 (OUTPUT SELECT) W F 3...
Page 25
DVM-1815 3 7 6 3 1 5 1 5 0 Progressive Block Diagram DATA(VIDEO) SIGNAL VIDEO SIGNAL IC1801 (DE-INTERLACER) IC1803 (PROGRESSIVE ENCODER) CN1801 TEST PATT.GENE. FORMATTER DE-INTERLACER FORMATTER /DELAY /GAMMA CORRECTOR DIGITAL SIGNAL PROCESS BLOCK DIAGRAM CN202 4:2:2 4:2:2...
Page 26
DVM-1815 3 7 6 3 1 5 1 5 0 Power Supply Block Diagram CAUTION ! CAUTION Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit. FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,...
DVM-1815 SCHEMATIC DIAGRAMS / CBA’S AND TEST POINTS 3 7 63 1515 0 Standard Notes WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replace- ment components rated for higher voltage, wattage, etc.
Page 28
DVM-1815 LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING 3 7 63 1515 0 PAGES: 1. CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE. ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQES D'INCELE N'UTILISER QUE DES FUSIBLE DE MÊME TYPE.
Page 29
DVM-1815 3 7 6 3 1 5 1 5 0 DVD Main 1/3 Schematic Diagram 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 http://www.xiaoyu163.com...
Page 30
DVM-1815 3 7 6 3 1 5 1 5 0 DVD Main 2/3 Schematic Diagram 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 http://www.xiaoyu163.com...
Page 31
DVM-1815 3 7 6 3 1 5 1 5 0 IC101 VOLTAGE CHART PIN.NO PLAY STOP PIN.NO PLAY STOP PIN.NO PLAY STOP PIN.NO PLAY STOP PIN.NO PLAY STOP PIN.NO PLAY STOP PIN.NO PLAY STOP PIN.NO PLAY STOP ----- -----...
Page 32
DVM-1815 3 7 6 3 1 5 1 5 0 DVD Main 3/3 Schematic Diagram 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 E8620SCD3 1-8-9 1-8-10 http://www.xiaoyu163.com...
Page 33
DVM-1815 3 7 6 3 1 5 1 5 0 AV 1/2 Schematic Diagram CAUTION CAUTION ! NOTE : FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit.
Page 34
DVM-1815 3 7 6 3 1 5 1 5 0 AV 2/2 Schematic Diagram 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 http://www.xiaoyu163.com...
Page 35
DVM-1815 3 7 6 3 1 5 1 5 0 Changer 1/2, Function, Power Switch & Switch Schematic Diagram 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 http://www.xiaoyu163.com...
DVM-1815 3 7 63 1515 0 FIRMWARE RENEWAL MODE 1.Turn the power on and remove the disc on the tray. Appearance State 2.To put the DVD player into version up mode, press [9], [8], [7], [6], and [SEARCH MODE] buttons on Reading...
Page 43
DVM-1815 3 7 63 1515 0 model: ****** Ver: **** Region: ** TEST 3: EEPROM CLEAR EEPROM CLEAR: OK RETURN: ----- EXIT: POWER Fig. h 10.To finish this mode, press [POWER] button. L 13942296513 u163 http://www.xiaoyu163.com...
DVM-1815 LEAD IDENTIFICATIONS 3 7 63 1515 0 2SK3374 KTC3198 (Y) 2SC2785 (H) KTC3205 (Y) KTC3199 (GR) 2SA966(Y) KRA110M KRC110M-AT BA1L3Z-T BN1L3Z (P) 2SA1015-Y (TPE2) KTA1266 (Y) KTA1267 (Y) DTC114ESA TP S D G E C B E C B...
DVM-1815 EXPLODED VIEWS 3 7 63 1515 0 Cabinet View 1 2L021 2L021 See Electrical Parts List for parts with this mark. 2L021 2L021 Some Ref. Numbers are not in sequence. 2L021 2L021 Relay CBA 2B12 2L061 2B21 2B22...
DVM-1815 3 7 63 1515 0 PARTS LIST PRODUCT SAFETY NOTE: Products marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper ser- vicing.
Page 49
DVM-1815 3 7 63 1515 0 Ref. No. Description Funai Parts No. DENON Parts.No W3006 22P FFC AV TO MAIN WX1E8620-022 9H26000433 W3007 9P FFC CONTROL TO MAIN WX1E8620-009 9H26000434 W3008 16P FFC AV TO CONTROL WX1E8620-116 9H26000435 PACKING & ACCESSORIES...