Christie digital systems projector user's manual 38-viv211-01 (56 pages)
Summary of Contents for Christie LX400
Page 1
LX400 U S E R M A N U A L - T E C H N I C A L G U I D E 020-000167-02...
Page 3
NOTICE for European Union members 《 ENGLISH 》 This is a Class A product in European Union. WARNING : This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. 《...
Page 4
《 PORTUGUÊS 》 NOTIFICAÇÃO para sócios de União europeus Trata-se de um produto Classe A, em União européia. AVISO : Trata-se de um produto Classe A. Num ambiente doméstico, este produto pode provocar interferências rádio, podendo ser necessário tomar medidas adequadas. 《...
• The image may not be displayed correctly when the input sync signal is a composite sync or a sync on G. • The HDMI input does not support the signals marked with *. LX400 User Manual - Technical Guide 020-000167-02 Rev. 1 (08-2009)
Color signal 0.286Vp-p (NTSC, burst), 75Ω terminator Color signal 0.300Vp-p (PAL/SECAM, burst) 75Ω terminator Brightness signal, 1.0Vp-p, 75Ω terminator Ground Ground VIDEO RCA jack • System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43 • 1.0±0.1Vp-p, 75Ω terminator LX400 User Manual - Technical Guide 020-000167-02 Rev. 1 (08-2009)
Page 9
• About the details of RS-232C communication, please refer to the following page. Signal Signal Signal 1 (No connection) 4 (No connection) 7 RTS 2 RD 5 Ground 8 CTS 3 TD 6 (No connection) 9 (No connection) LX400 User Manual - Technical Guide 020-000167-02 Rev. 1 (08-2009)
Page 10
AUDIO IN 4 CONTROL USB B type jack Signal 1 +5V 2 - Data 3 + Data 4 Ground RJ-45 jack Signal Signal Signal 1 TX+ 2 TX- 3 RX+ 6 RX- LX400 User Manual - Technical Guide 020-000167-02 Rev. 1 (08-2009)
Action (byte_0 - 1) Action Classification Content Change setting to desired value. Read projector internal setup value. INCREMENT Increment setup value by 1. DECREMENT Decrement setup value by 1. EXECUTE Run a command. LX400 User Manual - Technical Guide 020-000167-02 Rev. 1 (08-2009)
Page 12
• Provide an interval of at least 40ms between the response code and any other code. • The projector outputs test data when the power supply is switched ON, and when the lamp is lit. Ignore this data. • Commands are not accepted during warm-up. LX400 User Manual - Technical Guide 020-000167-02 Rev. 1 (08-2009)
Enter the desired authentication password. Password This setting will be the same for [Network Network Control Control Port1 (Port: 23)] and [Network Re-enter Control Port2 (Port: 9715)]. Authentication Default setting is blank. Password LX400 User Manual - Technical Guide 020-000167-02 Rev. 1 (08-2009)
Page 14
Header + Command data (‘04H’ + ‘00H’ + type (2 bytes) + ‘00H’ + ‘00H’) (2) The projector increases the setting value on the above setting code. (3) The projector returns the response code ‘06H’ to the PC. LX400 User Manual - Technical Guide 020-000167-02 Rev. 1 (08-2009)
Page 15
This is the value to make zero on the addition of the lower 8 bits from the header to the checksum. 6. Connection ID Random value from 0 to 255 (This value is attached to the reply data). LX400 User Manual - Technical Guide 020-000167-02 Rev. 1 (08-2009)
Page 16
Otherwise, an authentication error will be returned. NOTE • As for the transmission of the second or subsequent commands, the authentication data can be omitted when the same connection. LX400 User Manual - Technical Guide 020-000167-02 Rev. 1 (08-2009)