Panasonic DMP-BD79GA Service Manual
  1. Manuals
  2. Brands
  3. Panasonic Manuals
  4. Blu-ray Player
  5. DMP-BD79GA
  6. Service manual
Panasonic DMP-BD79GA Service Manual

Panasonic DMP-BD79GA Service Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
DMP-BD79GA
Model No.
DMP-BD79GC
DMP-BD79GN
DMP-BD79GT
DMP-BD79GW
DMP-BD79PU
DMP-BD79PH
Colour
(K).......................Black Type
Panasonic Corporation © 2013.
Unauthorized copying and distribution is a violation
of law.
ORDER NO.CHM1303006CE
Blu-ray Disc Player

Advertisement

Table of Contents
loading

Related Manuals for Panasonic DMP-BD79GA

Summary of Contents for Panasonic DMP-BD79GA

  • Page 1 ORDER NO.CHM1303006CE Blu-ray Disc Player DMP-BD79GA Model No. DMP-BD79GC DMP-BD79GN DMP-BD79GT DMP-BD79GW DMP-BD79PU DMP-BD79PH Colour (K).......Black Type Panasonic Corporation © 2013. Unauthorized copying and distribution is a violation of law.

  • Page 4: Table Of Contents

    TABLE OF CONTENTS PAGE PAGE 1 Safety Precautions -----------------------------------------------5 1.1. General guidelines -----------------------------------------5 1.2. Caution for fuse replacement ---------------------------5 1.3. Caution for AC cord (Only for BD79GC) -------------7 2 Warning --------------------------------------------------------------8 2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatic Sensitive (ES) Devices ---------------8 2.2.

  • Page 5: Safety Precautions

    1 Safety Precautions 1.1. General guidelines 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
  • Page 6 1.2.1. Micro Fuse conducting check This unit uses the Micro Fuse. Check the Micro Fuse conducting using the Tester at the check points below.

  • Page 7: Caution For Ac Cord (Only For Bd79Gc)

    1.3. Caution for AC cord (Only for BD79GC)

  • Page 8: Warning

    2 Warning 2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatic Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec- trostatic Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semi- conductor "chip"...

  • Page 9: Precaution Of Laser Diode

    2.2. Precaution of Laser Diode...

  • Page 10: Service Caution Based On Legal Restrictions

    2.3. Service caution based on legal restrictions 2.3.1. General description about Lead Free Solder (PbF) The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this equipment in considering the globally environmental conservation. The normal solder is the alloy of tin (Sn) and lead (Pb).

  • Page 11: Service Navigation

    3 Service Navigation 3.1. Combination of Multiple Pressing on the Remote Control Press multi-buttons (in combination) on the remote control simultaneously for operations, such as initialization or service mode, etc. 3.2. The display position of TV Special modes display of this unit changes to TV display from the original FL display. 3.3.
  • Page 12 3.3.1. Disclosure mode (Combination of multiple pressing: [OK] [Blue] [Yellow]) Press and hold [OK] [Blue] [Yellow] on the remote control simultaneously for 5 sec., then "00RET" is displayed on TV display window. 3.3.2. Nondisclosure mode 1 (Combination of multiple pressing: [6] [7] [Yellow]) Press and hold [6] [7] [Yellow] on the remote control simultaneously for about 5 sec., then "50RET"...

  • Page 13: How To Update Firmware

    This unit has 2 updating method, one way to update via the internet, the other way to update using CD-R or USB device which is stored pre-downloaded firmware update file. 3.4.2.1. Updating firmware via the internet Occasionally, Panasonic may release updated firmware for this To update the firmware unit that may add or improve the way a feature operates. These Press [HOME] updates are available free of charge.
  • Page 14 3.4.2.2. Updating firmware using the USB device When updating firmware using USB device, perform following procedures. (When using CD-R instead of USB device, perform same procedures) 1. Download the latest firmware file of the unit The latest firmware required for version-up can be downloaded from "Support Information from NWBG/VDBG-PAVC" web-site in "TSN system".

  • Page 15: Specifications

    4 Specifications USB Standard: USB2.0 High Speed Format: FAT12, FAT16, FAT32, NTFS, MP3, JPEG, MKV, MP4, MPEG2, WAV, FLAC,AAC,WMA,RMVB(BD79GT), Power supply: AC220V-240V, 50Hz (BD79GN) Xvid AC220V-240V, 50/60Hz (BD79GA/ Contents: GC/GW) JPEG: AC110V, 60Hz (BD79GT) CD-R/RW, BD-RE, DVD-R, USB device: AC110-240V,50/60Hz(BD79PU/PH) Pixcels: 34x34~8192x8192 Power consumption:...

  • Page 16: Location Of Controls And Components

    5 Location of Controls and Components...

  • Page 18: Operating Instructions

    6 Operating Instructions 6.1. Taking out the Disc from BD-Drive Unit when the Disc cannot be ejected by OPEN/CLOSE button 6.1.1. Forcible Disc Eject 1. Turn on the power, press and hold [OK], [B] and [Y] on the remote control at the same time for more than 5 seconds. "00RET"...

  • Page 19: Service Mode

    7 Service Mode 7.1. Special Mode Setting and Service mode 7.1.1. Self-Diagnosis Functions Self-Diagnosis Function provides information for errors to service personnel by “Self-Diagnosis Display” when any error has occurred. U** and F** are stored in memory and held. You can check latest error code by transmitting [0] [1] of Remote Controller in Service Mode. Automatic Display on FL will be cancelled when the power is turned off or AC input is turned off during self-diagnosis display is ON.
  • Page 20 Error Code Diagnosis contents Description Monitor Display Automatic TV display Initialization error When initialization error is detected after start- No display No display ing up main microprocessor, the power is turned off automatically. The event is saved in memory. Drive hardware error When drive unit error is detected, the event is No display No display...
  • Page 21 7.1.2. Special Modes Setting Item TV display Key operation Mode name Description Rating password The audiovisual level setting password is While the unit is on, press and initialized to Level 8. hold [OK], [B] and [Y] on the remote control at the same time for more than 5 seconds.
  • Page 22 Item TV display Key operation Mode name Description Demonstration Ejection of the disc is prohibited. *When lock the tray. While the unit is on, press and lock / unlock The lock setting is effective until unlocking the hold [OK], [B] and [Y] on the remote tray and not released by Main unit initializa- control at the same time for more tion of service mode.
  • Page 23 Item TV display Key operation Mode name Description Progressive initialization The progressive setting is initialized to inter- While the unit is on, press and lace. hold [OK], [B] and [Y] on the remote control at the same time for more than 5 seconds.
  • Page 24 7.1.3. Service Mode at a glance Information necessary for service can be displayed. Service mode setting: 1. Turn the power on. 2. Press the [5] [9] and [R] button simultaneously for five seconds, then [70RET] is displayed on TV. 3. Press the [ ] button to select until [80SRV] is displayed on TV.
  • Page 25 Item Key operation TV display Mode name Description (Remote controller key) Laser Used Time Check laser used time (hours) of drive. Press [4] [1] in service mode. Indication (****) is the used time display in hour. Laser used time of BD/DVD/ CD in Playback mode is counted.
  • Page 26 Item Key operation TV display Mode name Description (Remote controller key) BD Drive last error BD Drive error code display. 1. Error Number is displayed for 5 Press [4] [2] in service mode. seconds. 2. Time when the error has occurred is display for 5 seconds.
  • Page 27 Item Key operation TV display Mode name Description (Remote controller key) In case that the maker cannot be 6. Disc maker ID is displayed for 5 identified, display is blackout. seconds.
  • Page 28 7. Factor of drive error (hexadeci- mal) occurring is left displayed. 8. When the last error doesn't exist . PD Balance Measuring the PD balance. 1.Insert the Panasonic BD-VIDEO SL Disc(Ver 1.0/Ver 2.0) into the tray. (Incompatible with other media) 2.Press [4] [8].
  • Page 29 Item Key operation TV display Mode name Description (Remote controller key) CEC (L) Output The CEC terminal low output of HDMI. Press [5] [6] in service mode. Manufacturing Date Read out the manufacturing date of the unit. Press [6] [1] in service mode. YY: Year MM: Month DD: Date...
  • Page 30 Item Key operation TV display Mode name Description (Remote controller key) Delete the Error History Error History information stored on the unit is Press [9] [7] in service mode. deleted. Initialization of Error code Last Error Code information stored by timer is Press [9] [8] in service mode.

  • Page 31: Service Fixture & Tools

    8 Service Fixture & Tools Part Number Description Compatibility RFKZ0216 Extension Cable (Digital P.C.B. - Power P.C.B./ 23 Pin) Same as BDT220 Series RFKZ03D01KS Lead Free Solder (0.3mm/100g Reel) Same as BDT220 Series RFKZ06D01KS Lead Free Solder (0.6mm/100g Reel) Same as BDT220 Series RFKZ10D01KS Lead Free Solder (1.0mm/100g Reel)) Same as BDT220 Series...

  • Page 32: Disassembly And Assembly Instructions

    9 Disassembly and Assembly Instructions 9.1. Unit 9.1.1. Disassembly Flow Chart The following chart is the procedure for disassembling the casing and inside parts for internal inspection when carrying out the servicing. To assemble the unit, reverse the steps shown in the chart below. 9.1.2.
  • Page 33 9.1.3. Top Case 3. Remove the tray top from the tray section. 1. Remove the 3 Screws (A). 2. Slide Top Case rearward and open the both ends at rear side of the Top Case a little and lift the Top Case in the direction of the arrows.

  • Page 34: Front Panel

    9.1.4.2. Front Panel 9.1.6. Rear Panel 1. Unlock 6 tabs (A)-(F) turn. Pull with the Front Panel in the 1. Remove the Screw (A) and Screw (B). direction of your side. 2. Unlock 2 locking Tabs (C) to remove the Rear Panel. 9.1.7.

  • Page 35: Bd Drive

    9.2. BD Drive Notes when attaching the tray: 1. Push Slide cam to the left side slightly, and make sure the tray band is between the two posts of Slide cam 9.2.1. Tray when attaching the tray. 1. Insert the Paper clips, etc. into the hole of the bottom side, and slide it to the direction of arrow until it can be.
  • Page 36 9.2.3. Slide Cam 4. Slide the Slid cam in the direction as shown, and then take the front post out of the slide cam track. 1. Perform the step “ Pulley Gear, Belt ”. 2. Remove the OPU FFC sheet from the mecha chassis. 3.
  • Page 37 9.2.4. Drive Gear and Loading Motor 1. Perform the step “ Slide Cam ”. 2. Remove the Drive Gear. 3. Loosen the hooks, and remove the Loading Motor Unit and the SW Ass'y.
  • Page 38 9.2.5. Grease...

  • Page 39: Disassembly From The Traverse Unit, Assembly Of The Optical Pick-Up Unit, And Precautions On Esd-Preventive

    9.3. Disassembly from the traverse 3. Remove the Mid base. unit, assembly of the optical pick-up unit, and precautions on ESD-preventive 9.3.1. Disassemly 1. Before removing the optical pick-up unit, please apply an ESD prevention bag(RPFC0114) to the OPU FFC, and weld the short-circuit solder.
  • Page 40 9.3.2. Assembly 4. Press down the handle A of the two springs, and remove the shaft with OPU. 1. Insert the shaft into the shaft hole of the base, install the OPU to the auxiliary shaft, and then attach the nut piece unit onto the screw stem.
  • Page 41 4. Insert FFC, and desolder the solder spot. a. Use the iron head with an angle as shown in Fig,remove the solder in the direction as shown. b. Set the temperature of iron below 350°C. c. When using the iron head,do not apply a force more than 1N to the pad.
  • Page 42 9.3.3. How to Clean the Lens of Optical Pick-UP...

  • Page 43: Adjustment Of Bd Drive

    9.4. Adjustment of BD Drive 9.4.1. Repair Flowchart...
  • Page 44 9.4.2. Adjustment 9.4.2.1. [Drive] Input Engineering Adjusted Value([7] [2]) 1. Input [7] [2] with the remote control's numeral keys in the service mode. The TV display "DQR__"(__is blank)at this time.Engineering Adjusted Value display is in the input state. 2. Input Engineering Adjusted Value with remote control: The TV is displaying the input numeric from the left.(Use "*"...

  • Page 45: Measurements And Adjustments

    10 Measurements and Adjustments 10.1. Service Positions NOTE: For description of the disassembling procedure, see the section 9. 10.1.1. Checking and Repairing of Power P.C.B.
  • Page 46 10.1.2. Checking and Repairing of BD Drive and Digital P.C.B.

  • Page 47: Caution For Replacing Parts

    The Panasonic RAM disc should be recognized. Perform playback for one minute using the RAM disc. No abnormality should be seen in the picture, sound or operation. *Panasonic DVD-RAM disc should be used when recording and playback. Perform playback for one minute using the BD-Video disc.

  • Page 48: Block Diagram

    JK59001 TRACKING COIL OPTICAL DISC CONTROLLER/ AV DECODER/ MOTOR DRIVE ETHER NET PHYSIVAL LAYER PORT SYSTEM CONTROLLER TRAVERSE TRAVERSE MOTOR SPINDLE IC51078 MOTOR NAND FLASH LOADING ROM/1GB MOTOR X56501 IC52001/IC52201 P1104 SDRAM/1GB USB PORT REMOTE SENSOR DMP-BD79GA/GC/GN/GT/GW/PU/PH OVERALL BLOCK DIAGRAM...

  • Page 49: Power Supply Block Diagram

    POWER TRANSFORMER AC SOCKET P1001 F1001 SURGE SUPPRESSOR RECTIFIER AND SURGE ABSOBER IC1021 (SWITCHING IC) D1022 D1110 PW_X_SW12.2V P1102 P58001 22,23 FB/OLF DIGITAL P.C.B. D1111 PW_X_SW5.1V P1102 P58001 17,18,19 Q1022 (FEED BACK) IC1103 (ERROR VOLTAGE DET.) COLD DMP-BD79GA/GC/GN/GT/GW/PU/PH POWER BLOCK DIAGRAM...

  • Page 50: Digital P.c.b. Regulator Block Diagram

    IC55001- 9 18 PW_DR5V IC55003- 33 34 IC58300 (REG.1.5V) FROM P1102 P58001 PW_SW1.5V POWER P.C.B. 22,23 IC52001- VDD,VDDQ P_ON_H IC52201- VDD,VDDQ FROM MTK IC55004 IC51001- Y6 SECTION (REG.9.5V) A9P5V IC55003- 24 VOUT 1 PW_DR12V IC55003- 3 DMP-BD79GA/GC/GN/GT/GW/PU/PH DIGITAL P.C.B. REGULATOR BLOCK DIAGRAM...

  • Page 51: Digital (Back End Section) Block Diagram

    (PHYSICAL LAYER TRAVERSE) TXVP_0 TXVN_0 TXVP_1 JK56301 HDMI JACK 9 RX- TXVN_1 CH2_P CH2_M L56301 CH1_P CH1_M CH0_P CH0_M L56302 CLK_P CLK+ CLK_M CLK- CEC A19 Q56301 HDMISCK HDMISCL HDMISD HDMISDA HTPLG HOTPLG DMP-BD79GA/GC/GN/GT/GW/PU/PH DIGITAL BLOCK DIAGRAM (BACK END SECTION)

  • Page 52: Digital (Front End Section) Block Diagram

    STEPPING MOTOR DRIVE STEPPING SLED END MOTOR detection ENDDET PUMP1 SLD_ENA G_TRVB+ SLED2+ pre- power G_TRVB- driver SLED2- P55004 MCOM SIOV BEMF detector FEFG FEFG XSLEEP SPM Logic PUMP1 DAC PWM pre- power SPINDLE MOTOR DRIVE driver DMP-BD79GA/GC/GN/GT/GW/PU/PH SERVO BLOCK DIAGRAM...

  • Page 53: Wiring Connection Diagram

    POWER_LED POWER_LED REMOCON REMOCON PW_STANBY_3R3V PW_STANBY_3R3V POWER_KEY POWER_KEY BD DRIVE PW_X_SW5R1V PW_X_SW5R1V DIGITAL P.C.B. PW_X_SW5R1V PW_X_SW5R1V PW_X_SW5R1V PW_X_SW5R1V PW_X_SW12R2V PW_X_SW12R2V PW_X_SW12R2V PW_X_SW12R2V P55003 P55004 POWER P.C.B. P55005 LDM+ LDM+ LDM- LDM- OPENSW OPENSW CLOSESW CLOSESW DMP-BD79GA/GC/GN/GT/GW/PU/PH INTERCONNECTION SCHEMATIC DIAGRAM...

  • Page 54: Appendix Information Of Schematic Diagram

    13 Appendix Information of Schematic Diagram 13.1. Waveform Chart NOTE: Circuit waveform described herein shall be regarded as reference information when probing defect point, because it may differ from an actual measuring value due to difference of Measuring instrument and its measuring condition and product itself. 13.1.1.
  • Page 55 Model No. : DMP-BD79GA/BD79GC/BD79GN/BD79GT/BD79GW/BD79PU/BD79PH SCHEMATIC DIAGRAM NOTICE...
  • Page 56 Model No. : DMP-BD79GA/BD79GC/BD79GN/BD79GT/BD79GW/BD79PU/BD79PH PART LIST NOTICE...
  • Page 57 Model No. : DMP-BD79GA/BD79GC/BD79GN/BD79GT/BD79GW/BD79PU/BD79PH ABBREVIATION...
  • Page 58 Model No. : DMP-BD79GA/BD79GC/BD79GN/BD79GT/BD79GW/BD79PU/BD79PH POWER SECTION(POWER P.C.B.)
  • Page 59 Model No. : DMP-BD79GA/BD79GC/BD79GN/BD79GT/BD79GW/BD79PU/BD79PH LED SECTION(POWER P.C.B.)
  • Page 60 Model No. : DMP-BD79GA/BD79GC/BD79GN/BD79GT/BD79GW/BD79PU/BD79PH AUDIO DAC SECTION(DIGITAL P.C.B.)
  • Page 61 Model No. : DMP-BD79GA/BD79GC/BD79GN/BD79GT/BD79GW/BD79PU/BD79PH AV SECTION(DIGITAL P.C.B.)
  • Page 62 Model No. : DMP-BD79GA/BD79GC/BD79GN/BD79GT/BD79GW/BD79PU/BD79PH DIGITAL NET SECTION(DIGITAL P.C.B.)
  • Page 63 Model No. : DMP-BD79GA/BD79GC/BD79GN/BD79GT/BD79GW/BD79PU/BD79PH DDR SECTION(DIGITAL P.C.B.)
  • Page 64 Model No. : DMP-BD79GA/BD79GC/BD79GN/BD79GT/BD79GW/BD79PU/BD79PH MTK SECTION(DIGITAL P.C.B.)
  • Page 65 Model No. : DMP-BD79GA/BD79GC/BD79GN/BD79GT/BD79GW/BD79PU/BD79PH FE SA SECTION(DIGITAL P.C.B.)
  • Page 66 Model No. : DMP-BD79GA/BD79GC/BD79GN/BD79GT/BD79GW/BD79PU/BD79PH POWER P.C.B.(COMPONENT SIDE)
  • Page 67 Model No. : DMP-BD79GA/BD79GC/BD79GN/BD79GT/BD79GW/BD79PU/BD79PH POWER P.C.B.(FOIL SIDE)
  • Page 68 Model No. : DMP-BD79GA/BD79GC/BD79GN/BD79GT/BD79GW/BD79PU/BD79PH DIGITAL P.C.B.(COMPONENT SIDE)
  • Page 69 Model No. : DMP-BD79GA/BD79GC/BD79GN/BD79GT/BD79GW/BD79PU/BD79PH DIGITAL P.C.B.(FOIL SIDE)
  • Page 70 Model No. : DMP-BD79GA/BD79GC/BD79GN/BD79GT/BD79GW/BD79PU/BD79PH Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks ■ VEP71298V POWER P.C.B. (RTL) E.S.D. BD79GA ■ VEP71298P POWER P.C.B. (RTL) E.S.D. BD79GC/GN/GW ■ VEP71298K POWER P.C.B. (RTL) E.S.D. BD79GT ■ VEP71298H POWER P.C.B.
  • Page 71 Model No. : DMP-BD79GA/BD79GC/BD79GN/BD79GT/BD79GW/BD79PU/BD79PH Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks R1113 D0GB103JA065 1/10W 1K R1115 ERJ3RBD822V 1/16W 8.2K R1116 D0GB222JA065 1/10W 2.2K R1119 ERJ3RBD103V 1/16W 10K R1121 ERJ3RBD102V 1/16W 1K R1123 D0GD682JA052 1/8W 6.8K...
  • Page 72 Model No. : DMP-BD79GA/BD79GC/BD79GN/BD79GT/BD79GW/BD79PU/BD79PH Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks C52025 F1G1A1040006 10V 0.1U C52026 F1G1A1040006 10V 0.1U C52030 F1J0J2260004 6.3V 22U C52031 F1G1A1040006 10V 0.1U C52032 F1G1A1040006 10V 0.1U C52033 F1G1A1040006 10V 0.1U C52034 F1G1A1040006 10V 0.1U...
  • Page 73 Model No. : DMP-BD79GA/BD79GC/BD79GN/BD79GT/BD79GW/BD79PU/BD79PH Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks C55066 F1G1E1040001 25V 0.1U C55067 F1G1A1040006 10V 0.1U C55068 F1G1A1040006 10V 0.1U C55076 F1G1C104A077 16V 0.1U C55077 F1G1C104A077 16V 0.1U C55079 F1G1A1040006 10V 0.1U C55080 F1H0J2250008 6.3V 2.2U...
  • Page 74 Model No. : DMP-BD79GA/BD79GC/BD79GN/BD79GT/BD79GW/BD79PU/BD79PH Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks C59002 F1G1A1040006 10V 0.1U IC51001 RFKB76325KT 1 E.S.D. ADJ BD79GA IC51001 RFKB76325KCT 1 E.S.D. ADJ BD79GC IC51001 RFKB76325GT 1 E.S.D. ADJ BD79GN IC51001 RFKB76325KTT 1 E.S.D.
  • Page 75 Model No. : DMP-BD79GA/BD79GC/BD79GN/BD79GT/BD79GW/BD79PU/BD79PH Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks R51006 D0GA103JA023 1/16W 10K R51025 D0GA472JA023 1/16W 4.7K R51027 D0GA472JA023 1/16W 4.7K R51028 D0GA472JA023 1/16W 4.7K R51032 D0GAR00J0005 1/16W 0 R51036 D0GA103JA023 1/16W 10K...
  • Page 76 Model No. : DMP-BD79GA/BD79GC/BD79GN/BD79GT/BD79GW/BD79PU/BD79PH Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks R59001 D0GA750JA023 1/16W 75 R59002 D0GA750JA023 1/16W 75 R59003 D0GA750JA023 1/16W 75 R59004 D0GA750JA023 1/16W 75 R59302 D0GA103JA023 1/16W 10K R59311 D0GA103JA023 1/16W 10K...
  • Page 77 Model No. : DMP-BD79GA/BD79GC/BD79GN/BD79GT/BD79GW/BD79PU/BD79PH Exploded View...
  • Page 78 Model No. : DMP-BD79GA/BD79GC/BD79GN/BD79GT/BD79GW/BD79PU/BD79PH Mechanism View...
  • Page 79 Model No. : DMP-BD79GA/BD79GC/BD79GN/BD79GT/BD79GW/BD79PU/BD79PH Packing View...
  • Page 80 Model No. : DMP-BD79GA/BD79GC/BD79GN/BD79GT/BD79GW/BD79PU/BD79PH Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks ■ CASING VXY2171T BD DRIVE 1 ADJ VEP71298V POWER P.C.B. 1 (RTL) E.S.D. BD79GA VEP71298P POWER P.C.B. 1 (RTL) E.S.D. BD79GC/GN/GW VEP71298K POWER P.C.B.
  • Page 81 Model No. : DMP-BD79GA/BD79GC/BD79GN/BD79GT/BD79GW/BD79PU/BD79PH Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks 119-1 L6KAYYYH0010 STEPPING MOTOR 119-2 VMS8126 SHAFT 119-3 VMB4682 SHAFT SPRING 119-4 VMB4682 SHAFT SPRING 119-5 XTN2+4FFJ STEPPING MOTOR SCREW 119-6 XTN2+4FFJ STEPPING MOTOR SCREW...

This manual is also suitable for:

Dmp-bd79gcDmp-bd79gtDmp-bd79gwDmp-bd79puDmp-bd79phDmp-bd79gn

Table of Contents