Advertisement
Quick Links
Read through these instructions completely before commencing installation. Retain for future use.
1
Specifications
Cat No.
Supply voltage
Power rating
Protection class
IP rating
Draught stopper
Duct diameter
Engine size
Engine weight
Power cord length
Ceiling cut-out size (for inlet & outlet grilles)
Max airflow (m
/hr)
3
Duct length
No duct
1m per side (total 2m)
2.5m per side (total 5m)
2
Features
The inline fan is designed to extract steam and odours from a bathroom and expel it to the exterior through an eave outlet. It is also suitable for
extracting air from one room and expelling it to another room (heat distribution).
The fan engine is fitted into the ceiling, well away from the inlet. This inline feature allows the inlet grille to be mounted in wet areas (near the splash
zones of bathrooms) or even above the shower. And because the motor is in the ceiling cavity (away from the inlet grille), noise from the fan is minimal.
3
Please Read Carefully
1. This product shall be installed in accordance to AS/NZS 3000 Wiring Rules.
2. This product is meant for indoor use only.
3. Regulations concerning the discharge of air must be fulfilled. Local building codes may require venting to the outside.
4. Do not locate the inlet grille above a stove. This product is not to be used in conjunction with a kitchen range hood exhaust system.
5. The minimum length of duct between the fan engine and the inlet / outlet grilles is 200mm.
6. Cross Ventilation:
Ventilation products must have an adequate source of external air to ensure rated performance.
Inline Exhaust Fan Kit – 100mm & 150mm
EFIL100SQWE
30W
Ø100mm
290 x 200 x 210mm
1.9kg
Ø110mm
Low Speed (I)
High Speed (II)
200
255
100
125
90
115
Cat. No. EFIL100SQWE, EFIL150SQWE
Instruction Manual
EFIL150SQWE
230-240V a.c. 50Hz
Class II
IP44
Yes (PET Sheet)
Ø150mm
290 x 230 x 250mm
1m
Ø160mm
Low Speed (I)
450
310
270
60W
3.0kg
High Speed (II)
555
390
335
Advertisement
Related Manuals for HPM EFIL150SQWE
Summary of Contents for HPM EFIL150SQWE
-
Page 1: Specifications
Inline Exhaust Fan Kit – 100mm & 150mm Cat. No. EFIL100SQWE, EFIL150SQWE Instruction Manual Read through these instructions completely before commencing installation. Retain for future use. Specifications Cat No. EFIL100SQWE EFIL150SQWE Supply voltage 230-240V a.c. 50Hz Power rating Protection class... - Page 2 Steam and air will only be exhausted through the fan if there is sufficient flow of air through the room. Ensure adequate inlets exist through windows, vents or under the door. Airflow path from the inlet to the fan should ideally pass over the source of steam or air to be removed from the room. Restrictions on replacement air entering the room to be ventilated, or pressure-differentials between the room and outside air will significantly reduce the exhaust fan’s performance.
-
Page 3: Air Inlet
Fig. 5 describes how to mount the grille onto the ceiling/eave. Mounting holes Fig. 5 Body Step 1: Remove the louvre Step 2: Remove the mesh Step 3: Attach Body to ceiling/eave using the 4 mounting holes. Step 4: Replace the mesh and louvre Step 4: Clip on the other grille Fan Engine Fig. - Page 4 7. This product contains no serviceable parts and no attempt should be made to repair it. If the product is faulty it should be discarded. 8. If the supply cord is damaged, it must be replaced by HPM Legrand, its service agent or a similarly qualified person in order to avoid a hazard.