Subscribe to Our Youtube Channel
Related Manuals for Avocent UMG-2000
Summary of Contents for Avocent UMG-2000
- Page 1 Unified Office Gateway UMG-2000 / UMG-2100 / UMG-2200 Version: 1.1 Quick Installation Guide...
-
Page 2: Table Of Contents
1. Package Contents ..................3 2. Overview ....................4 3. Hardware Installation ................... 6 3.1 Unpack the UMG-2000 / UMG-2100 / UMG-2200 ........6 3.2 Choosing a Setup Location..............6 3.3 Preparing for Setup ................7 3.4 Precautions ..................7 3.5 Installation Consideration ............... -
Page 3: Package Contents
1. Package Contents UMG-2000 / UMG-2100 /UMG-2200 Unit x 1 AC Power Cord x 1 CD x 1 Quick Installation Guide x 1 Ear Brackets x 2 Desk Brackets x 2 Brackets Fixing Screws x 12 Plug Screws x 4... -
Page 4: Overview
2. Overview Front Panel Power On PWR LED Power Off Connect to Internet Internet LED Disconnect to Internet PBX function turn on PBX LED PBX function turn off Wireless function turn on WLAN LED Wireless function turn off E-mail function turn on E-mail LED E-mail function turn off Firewall/Security function turn on... - Page 5 Press the button to pop out the SATA carrier Rear Panel Cooling Fans System cooling fans on rear panel UMG-2000 : 4 x RJ-11 (4 x FXO) Voice (P1) UMG-2100 : 1-Port T1/E1 PRI UMG-2200 : 8 x RJ-11 (8 x FXO) 1 x 802.11b/g/n Wireless Access Point, 2 x Antenna...
-
Page 6: Hardware Installation
Leave approximately 40cm (16inche) of clearance in front of the UMG-2000 / UMG-2100 / UMG-2200 to ensure the disk carriers can be unplugged. Leave approximately 30cm (12 inch) of clearance in the back of the UMG-2000 / UMG-2100 / UMG-2200 to allow for sufficient airflow and ease in servicing. -
Page 7: Preparing For Setup
Review the electrical and general safety precautions. Install the heaviest server components on the bottom of the rack first, and then work up if you want to mount the UMG-2000 / UMG-2100 / UMG-2200 to a rack. Use a power supply regulating uninterruptible (UPS) to protect the server from failure. -
Page 8: The Desktop Brackets Installation
It is strongly recommended to securely fasten the mounting rack to the floor or wall to eliminate any possibility of tipping over the rack. This is especially important if you decide to install several UMG-2000 / UMG-2100 / UMG-2200 chassis in the top of the rack. -
Page 9: The Hard Disk Installation
Mount the server into the rack. Lock the server to the rack by mounting the ear brackets to the rack. 3.8 The Hard Disk Installation The SATA subsystem supports four hot-swappable hard drives. The SATA drives are inserted to the SATA backplane that provides power and bus termination. 1. - Page 10 Locate the storage subassembly. Press the disk carrier switch to unlock the carrier. Unplug the disk carrier by pulling the carrier handler. Mount the disk into the carrier and load the fixing screws. Press the disk carrier switch to insert the carrier to the disk slot. Close the disk carrier lock/switch to lock the carrier.
-
Page 11: Physical Connection
4. Physical Connection 4.1 WAN Connection Locate the WAN port on the rear panel. Connect the WAN port with the Ethernet cable. 4.2 LAN Port Connection There are 26 Ethernet ports on the rear panel. The port 1 to 24 are 10/100 Mbps Ethernet ports and the port 25 and port 26 are 10/100/1000 Ethernet ports. -
Page 12: Pstn Fxo Port Connection
4.3 PSTN FXO Port Connection Locate the voice port of the PSTN adapter on the rear panel. The Analog PSTN port may vary from 4 / 8 FXO ports. Connect one or more telephone cables to one of the selected FXO port. 4.4 ISDN T1/E1 Port Connection Locate the digital voice port of the T1/E1 adapter on the rear panel. -
Page 13: Quick Setup Wizard
5.1 First Time Login Now that the network connection between your PC and UMG-2000 / UMG-2100 / UMG-2200 has been established, you must login in order to access PLANET View. Launch a web browser (for example: IE, Firefox etc.) and type the UMG-2000 / UMG-2100 / UMG-2200 IP address in the address bar. -
Page 14: Welcome To Quick Start
“Faster Recovery UMG to UMG” which will be explained in the user’s manual. The quick start includes five steps which will lead administrator to setup the UMG-2000 / UMG-2100 / UMG-2200. Check the first radio box and then click the button “Start” to continue. - Page 15 Step 2: Activating UMG-2000 / UMG-2100 / UMG-2200 services The UMG-2000 / UMG-2100 / UMG-2200 allow the administrator to activate the service on demand. By default, all services are inactive. The administrator can activate the service in this page by checking the radio box of the corresponding service.
- Page 16 AUTO DETECT ISP TYPE By clicking the button “Detect”, you can make the UMG-2000 / UMG-2100 / UMG-2200 to recognize the ISP type automatically. It may take a while to detect your ISP type. Please wait. The ISP type will be detected and the result will be presented as follows. If “Network Cable Disconnected”...
- Page 17 MANUAL SETUP INTERNET CONFIURATION: STATIC If your ISP type is “Static”, choose it as your ISP type and setup the configuration. Item Description IP Address Specify the static IP address. Subnet Mask Address Specify the subnet mask address. Default Gateway Address Specify the IP address of the default gateway.
- Page 18 MANUAL SETUP INTERNET CONFIURATION: PPPOE If your ISP type is “PPPoE”, choose it as your ISP type and setup the configuration. Item Description Login Name Specify the login username to the PPPoE server. Password Specify the login password to the PPPoE server. Confirm Password Retype the password.
- Page 19 Item Description PPTP Server Specify the PPTP server IP address. Login Name Specify the username to login to the PPTP server. Specify the corresponding password to login to the PPTP Password server. Confirm Password Retype the password. Static IP Address Specify whether you have a static WAN IP address.
-
Page 20: Further Information
Step 5: Creating the Network Storage This page allows the administrator to quickly setup the storage. Specify the Redundant Array of Independent Disks (RAID) level and then click the button “Next” to go to step 6. Step 6: Confirmation Please recheck your input data to ensure the accurate. Click the button “Back” to make changes.
Need help?
Do you have a question about the UMG-2000 and is the answer not in the manual?
Questions and answers